Fenix ECOSUN E 700 IKP User manual

MOUNTING INSTRUCTIONS
N150/R03 (24.09.13)
ECOSUN LOW-TEMPERATURE RADIANT HEATING PANELS
IKP, IN, IN-2
Type Dimensions
mm
Voltage
V
Input
W
Safety
classification
Degree of
protection
Application areas and heating
categories
E 700 IKP
592x1192x30
(40) 230 I
IP 54
E 700 IN IP 65
E 700 IN-2 IP 65 Areas 1,2 (SNV 1,2)
II 2G Ex e II T3
700
Use:
Especially for heating in industrial and agricultural applications.
Description:
Low-temperature radiant panels are assembled from a two-part case (FeZn 0.6mm) sealed against
the outside environment with sealant (IN, IN-2); all seams and openings are puttied (IKP). The heating
element is a resistive conductor. The front and sides of the panel are given a special surface treatment
based on dispersion acrylic paint and silica sand. The back side of the panel is not painted.
Power cords:
E 700 IKP: rubber cord H05 RR-F 3G1
E 700 IN: silicon cord V05SS-F 3G x 0.75
E 700 IN-2: silicon cord V05SS-F 3G x 1 with a protective sleeve
Bushings:
E 700 IKP: F0705SR-5R1
E 700 IN: plastic V-TEC PG 9
E 700 IN-2: metal AGRO AG
Dimensions of the mounting frame:
Installation:
Panels are installed beneath the ceilings, hung with chains or ropes. When using a mounting frame, they
are attached directly to the ceiling. If the ceiling is made of a fl ammable material, it is necessary to mount
the panels at least 5 cm from the fl ammable surface. Flammable objects must be at least 10 cm from the
front and sides.

Product type: Date: Stamp, signature:
Product number (label on the back): _ _ _ _ - _ _ _ _ - _ _ _ _ - _ _ _ _ - _ _ _ _
Fenix Trading s.r.o.
Slezská 2, 790 01 Jeseník
tel.: [phone], fax: [phone]
e-mail: [email protected] , http://www.fenixgroup.cz
Assembly using the mounting frame:
Important Reminders:
• Electric connection and first commissioning can by performed by worker with adequate qualification.
• The temperature of the space (temperature of the surrounding air) where the radiant panel is placed must not exceed 30°C.
• The supply cord must be properly equipped for disconnecting from the power network, with the distance of the break contacts at least
3.5 mm at all poles. If the device‘s supply cord is damaged, it must be replaced by the manufacturer or by a service technician.
E700IN and E700IN2 panels cannot be repaired.
• When connecting the panel to fi xed wiring using the supply cable, it is necessary to observe the color designation for the live wires.
In connecting the E700IN-2, it‘s supply must include a residual current protection device having a trip current of ≤30mA.
• In mounting the installation frame, use countersunk screws.
• We recommend that gloves be worn while handling the panel so that the surface of the radiant panel is not soiled.
• Cleaning is possible with water and detergent using a soft brush.
• The mounting frame is not part of the panel.
• It is possible to renew the paint with a base of DISKOR V2076 and a two-layer top coat of BALAKRYL V2045.
• This appliance is not intended for use by persons (including children) whose lack of physical, sensory or mental ability or lack of
experience and knowledge prevents them from safely using the appliance, unless they are supervised or have received instructions
regarding the use of the appliance from a person who is responsible for their safety. Children should be supervised in order to prevent
them from playing with the appliance.
Terms of the warranty:
The product is covered by warranty for 24 months from the purchase date. The warranty does not cover problems incurred during
transportation, improper storage or unprofessional installation.