Fermax FERMVISION User guide


1



















 
Toactivatemoduletypein
Code8880+Okayinthe
monitorsettings
2WIRESYSTEM
FVQ‐1050CCTV

IPCCTVINTERFACE
FVQ‐1050CCTV
INSTALLERMANUAL
OnlycompatiblewithFermvision8MPcameras
Withlatestfirmware


2

Contents
MonitorDescription......................................................................................................................................................3
Step1–AddaUsertotheNVR....................................................................................................................................4
Step2–WiretheSystem..............................................................................................................................................7
Step3‐MonitorConfigurations...................................................................................................................................9
Appendix:AddausertoyourexistingNVRusingMobileDevice...............................................................................11




3

MonitorDescription

NO Name Description
1 RJ45 NetworkConnection
2 USBConnector USBMouse
3 HDMI HDMIOutput
4 PowerConnector 12VDCInput
–
DoNotUse
5 DIPSwitches Disabled
6 MicroSDCard Disabled
7 ToggleSwitch Settoleftposition
8 BusConnection BUS1&BUS2
–
Systemconnectionbus
ConnectedonDoorStationBUS
9 Button Disabled
10 ResetButton ResetButton–Holdfor3Secondstodefaultallsettings
11 LED1–Green On–Standby
Flashquickly–Startinguporresetting
FlashSlowly–PreviewingIPCamera
12 LED2–RED On–Standby
FlashSlowly–ConfiguringIPCamera


Mustbesettoleftposition.


4

Step 1 –AddaUsertotheNVR
IfyoudonothaveamonitorconnectedtotheNVRpleaseusetheAppendixtoaddauserusingyourmobiledevice.
LogintothemenuontheNVR
1. ClickSystem

2. ClickonUser



5
3. ClickAdd

4. Enterthefollowingdetails
Username:fermvision
Password:fermvision123Q@

Un‐tickallbasic
permissions.


6

5. ClickOKandmakesurethenewuserisnowadded.





7
PLUGANDPLAY
PORTS NetworkPort
P16
P8
P1 P9
REARFERMVISIONNVR
Alwaysplugintothelastplugandplayport
Example
Port4ona4Channel
Port8on8Channel
Port16on16Channel
AlwayswireondoorstationBUS
BUS(IM) BUS(DS)
PC 6
10 A GP0
DoNotConnect12VDCPower
ToDoorStationBUS
ToMonitorBUS
Toactivatemoduletypein
Code8880+Okayinthe
monitorsettings
Step 2–WiretheSystem

Thedeviceispre‐programmedforFermvisionNVR’susingtheplugandplaymethod.ThismeansallFermvision
cameraspluggedintoaFermvisionplugandplayportsoftheNVR.TheFVQ‐1050CCTVmodulewillalsobeplugged
intothelastportontheFermvisionplugandplayports.

























8

WithMultipleDoorStations 
PLUGANDPLAY
PORTS NetworkPort
P16
P8
P 1
P9
REARFERMVISIONNVR
Alwaysplugintothelastplugandplayport
Example
Port4ona4Channel
Port8on8Channel
Port16on16Channel
B US( I M) BUS ( DS)
PC6
10 A GP0
DoNotConnect12VDCPower
ToMonitorBUS
Toactivatemoduletypein
Code8880+Okayinthe
monitorsettings
DBC-4S
A B C D

BUS
FRONTDOORSTATION#1
BUS
FRONTDOORSTATION#2
6012 D
Keypad Code
1234 #, 11#, 1#, *.
Keypad Code
1234 #, 11#, 2 #, *.
NetworkCable


9
Step3‐Monitor Configurations

ToenabletheFVQ‐1050CCTVmoduleonthemonitorfollowthebelowsteps

Touchthe buttontoaccesstheSettingsmenu.





TypeinCode–8880+OK




10
OntheMainScreenbypressing youwillnowseeanewIcon



Clickonthecamerayouwouldliketosee.






11
Appendix:AddausertoyourexistingNVRusingMobileDevice

1OpentheFermvisionViewerapp onyoursmartphonewhileonthesamenetwork

2ClickontheMenubutton

3ClickonDevices


12


4ClickAddDevice

5ClickonAutoSearchinLAN


13

6FindthedevicethatsaysNVRandwritedowntheIPaddressexample192.168.1.106



14
7OpenupChromeonyourMobiledevice.TypeintheIPaddressthatyoufoundonstep6.Ascreenbelowshould
appear.

8Loginusingyourusernameandpasswordprovidedtoyoufromyourinstaller.
9ClickonSetup




15
10Clickonuserontheleftmenu

11ClickonUser






16
12ClickonAdd


13Enterthefollowingdetails
Username:fermvision
Password:fermvision123Q@



Un‐tickallbasic
permissions.


17
14Savethenewuser

15CheckyouhaveanewUser

