Fermax LYNX VIVO Instruction Manual

ENGLISH
LYNX Monitors
USER & INSTALLER'S MANUAL

Page 2
LYNX Monitor
User and installer’s manual for LYNX MONITORS
This manual includes basic instructions for the installation, programming and commissioning of LYNX
monitors.
Code 970013I V11_16
This technical document has been edited by FERMAX ELECTRÓNICAfor informational purposes, and the
company reserves the right to modify any of the technical specifications of the products referred to herein
at any time without prior notice. These changes shall be reflected in later editions of the same document.

Page 3
LYNX Monitor
INDEX
1. INTRODUCTION.......................................................................................................................6
1.1 FUNCTION DESCRIPTION: LED NAVIGATION BUTTONS AND ICONS.......................................6
Function description .......................................................................................................................................8
Buttons............................................................................................................................................................8
Icons................................................................................................................................................................8
2 SCREEN DESIGN. START MENU .........................................................................................10
2.1 STRUCTURE AND ARRANGEMENT OF FUNCTIONS .................................................................12
3 DESCRIPTION OF FUNCTIONS AVAILABLE ON MONITOR................................................15
3.1 GENERAL SETTINGS....................................................................................................................15
3.1.1 CALL SETTINGS ...................................................................................................................................15
3.1.2 BACKGROUND SETTINGS...................................................................................................................16
3.1.3 LANGUAGE SETTINGS ........................................................................................................................16
3.1.4 PICTURE SETTINGS.............................................................................................................................16
3.1.5 INTERNATIONAL SETTINGS................................................................................................................17
3.1.6 PRIVACY SETTINGS (USER) ...............................................................................................................17
3.1.6.1 PIN required...............................................................................................................................17
a) User settings..........................................................................................................................17
b) Reading messages................................................................................................................18
3.1.6.2 Change PIN................................................................................................................................19
a) User PIN................................................................................................................................19
b) Alarm PIN...............................................................................................................................19
3.1.7 HOME-TO-HOME CALL SETTINGS......................................................................................................20
3.1.8 “Push to Talk” AUDIO mode...................................................................................................................20
3.1.9 INSTALLER SETTINGS.........................................................................................................................21
3.1.9.1 MONITOR SETTINGS...............................................................................................................21
a) Standard Lynx Mode / c) Static IP Mode...............................................................................22
b) DHCP Mode...........................................................................................................................22
3.1.9.2 DELETE ALL SETTINGS (Reset) .............................................................................................22
3.1.9.3 LIFT SETTINGS CONTROL......................................................................................................23
3.1.9.4 OPTIONAL FUNCTIONS...........................................................................................................23
3.1.9.5 ALARM SETTINGS...................................................................................................................24
3.1.9.6 HOME AUTOMATION SETTINGS.............................................................................................25
3.1.9.7 INSTALLER PRIVACY SETTINGS ............................................................................................26
a) User PIN................................................................................................................................26
b) Alarm PIN...............................................................................................................................27
c) Installer PIN ...........................................................................................................................27
3.1.9.8 SD CARD MENU .......................................................................................................................27
3.1.9.9 MOBILITY SETTINGS ...............................................................................................................28
3.1.9.10 RELAY CONTROL...................................................................................................................28
3.1.9.11 DOORBELL SETTINGS...........................................................................................................29
3.1.9.12 IP CAMERA CONFIGURATION...............................................................................................30
a) Add camera .........................................................................................................................30
b) Edit camera .........................................................................................................................30
a) - b) Test camera...................................................................................................................31
c) Delete camera/s...................................................................................................................31
3.2 DEFAULT FUNCTIONS + OPTIONAL FUNCTIONS ENABLED.....................................................32
3.2.1 DO NOT DISTURB MODE....................................................................................................................32
3.2.2 CAMERAACTIVATED...........................................................................................................................33
3.2.3 CALL PROPERTY MANAGEMENT UNIT (PMU).................................................................................33
3.2.4 RECEIVE MESSAGES.........................................................................................................................34
3.2.5 ALARM MODE ......................................................................................................................................35
Sabotage detection system (alarms).....................................................................................................38
3.2.6 AUTOMATION.......................................................................................................................................38

Page 4
LYNX Monitor
3.2.7 AUDIO NOTES......................................................................................................................................38
a) Record audio note.............................................................................................................................39
b) Play back audio note.........................................................................................................................39
3.2.8 CALL HISTORY.....................................................................................................................................40
a) Calls made........................................................................................................................................40
b) Calls received ...................................................................................................................................40
c) Missed calls.......................................................................................................................................41
3.2.9 INTERNAL CALLS................................................................................................................................41
3.2.10 EXTERNAL CALLS.............................................................................................................................42
3.2.11 IP CAMERAS ......................................................................................................................................42
3.2.12 IMAGE VISUALISATION.....................................................................................................................43
3.2.13 LIFT CONTROL...................................................................................................................................43
3.2.14 DOORMATIC.......................................................................................................................................44
3.2.15 SEND MESSAGES.............................................................................................................................44
3.2.16 TIMER.................................................................................................................................................45
3.2.17 SCREEN CLEANING..........................................................................................................................45
3.2.18 CONTACT LIST - FRIENDSHIP REQUEST .......................................................................................46
3.2.19 MOBILITY............................................................................................................................................48
a) Link mobile device..........................................................................................................................49
b) List of mobile devices .....................................................................................................................49
3.2.20 RELAY CONTROL .............................................................................................................................50
3.2.21 F1 .......................................................................................................................................................50
3.2.22 INDUCTION LOOP .............................................................................................................................50
4 CONFIGURING THE MONITOR FROM THE WEB SERVER.................................................51
5 CALLS......................................................................................................................................52
5.1 RECEIVING CALLS.........................................................................................................................52
5.2 MAKE CALLS..................................................................................................................................54
a) Call/connection outdoor panel ...................................................................................................................54
b) IP Camera connection................................................................................................................................54
c) Call the Property Management Unit - PMU (concierge).............................................................................54
d) Intercommunication: Calls between monitors............................................................................................55
d) Panic calls (SOS button)............................................................................................................................55
6 INSTALLATION - MONITOR MEASUREMENTS....................................................................57
6.1 SMILE MONITOR............................................................................................................................57
FLUSH-MOUNT Installation...........................................................................................................................57
SURFACE-MOUNT Installation......................................................................................................................57
DIMENSIONS (Flush / Surface).....................................................................................................................58
6.2 VIVO+ MONITOR............................................................................................................................58
DIMENSIONS.................................................................................................................................................58
7 CONNECTORS - TECHNICAL SPECIFICATIONS.................................................................59
7.1 SMILE MONITOR............................................................................................................................59
a) Connectors..................................................................................................................................59
b) Technical Specifications..............................................................................................................60
7.2 VIVO/VIVO+ MONITOR...................................................................................................................61
a) Connectors..................................................................................................................................61
b) Technical Specifications..............................................................................................................62

Page 5
LYNX Monitor
CONGRATULATIONS ON BUYING A QUALITY PRODUCT!
Fermax Electrónica develops and manufactures premium equipment that meets the highest design and
technology standards.
Lynx monitors are technological devices designed to maximise communication, safety and comfort in the
home.
All of the monitor’s available functions are described in this manual. These functions may be enabled or
disabled as you wish, according to your installation requirements.

Page 6
LYNX Monitor
SOS
1. INTRODUCTION
LYNX Monitors are internet protocol-based monitors. These monitors are part of the LYNX system: data,
audio and TCP / IP-based multi-channel video. They communicate with a panel based in an IP video door
entry system (the LYNXAudio and Video module) and a PC-based Guard Unit (the Property Management
Unit, PMU).
This is a technological device designed to maximise communication, safety and comfort in the home.
Lynxmonitors are hands-free(bydefault), with duplexaudio, colour video withtouch screens andadditional
function buttons for the most common functions. There is the option of a “Push to Talk” audio mode.
On the touch screen, the options will be displayed via graphic icons. Navigation may be performed via the
icons, and selections made by pressing on the screen.
Setting the monitor to standby will turn off the screen.
The monitors are installed on walls via their corresponding connectors.
Monitors:
- VIVO Monitor: 7” touch screen - VIVO LYNX Connector Ref. 1605.
- VIVO+ Monitor: 10” touch screen - VIVO LYNX Connector Ref. 1605.
- Lynx SMILE Monitor: 7” touch screen - SMILE LYNX Connector Ref. 1655.
DO NOT DISTURB MODE
Door open
Message alert Out Sleep Home
Alarm modes configuration
Panic button MENU button Touch screen
Icon-button display on VIVO / VIVO MONITORS
1.1 FUNCTION DESCRIPTION: LED NAVIGATION BUTTONSAND ICONS
Onceswitchedon,themonitorwillstartup and display the FERMAX logo, firmwareversion, MAC address
and IP address. The boot-up process finishes in 60 seconds and the monitor enters in stand-by mode.
Fermax Monitor VIVO Firmware F_V03.00.007
MAC=00:04:9FEA:D3.
IP=10.0.0.1

Page 7
LYNX Monitor
The firmware version is also displayed on the
Installation Settings screen.
Icon-button display on SMILE MONITORS
DO NOT DISTURB MODE
Message alert
Outside Sleep Home
Alarm modes
configuration Audio Activation and
Hang-Up Button
MENU button
Touch screen
DoorOpeningButton
Panic button (SOS)
The screen may be deactivated by pressing the power off icon; otherwise this occurs automatically after
30 seconds of inactivity.
To access some of the screen’s basic functions, touch the screen or press the MENU button, which will
activate and allow you to select the icon corresponding to the desired function.
Different LED icons can be displayed via the monitor or illuminated push buttons (depending on the
function),toindicate additional activated statesandfunctions.The icon isonlyvisible when the LED ison.
Fermax SMILE Firmware version F _V03.00.007_SMILE
MAC=28:04:E0:FF:71:52.
IP=10.0.0.1
Important note:
- On the SMILE monitor, the time setting may be lost after a power failure. The SMILE monitor will consult the
outdoor panel for the time when starting, therefore it is important to configure the date and time correctly on all
panels. Incorrect time synchronisation of system monitors can lead to unexpected problems.

Page 8
LYNX Monitor
Buttons MENU button
When the touch screen is idle, pressing MENU will turn the screen on.
When the touch screen is on, pressing MENU will turn the screen to idle.
Whenthe user is navigatingasub-menu, pressing MENUcausesthe monitor toreturn
to the main home screen.
Note:
- When the touch screen is idle, pressing this will also turn the screen on.
Function description
SOS
Panic button. See section: 5. CALLS (Panic calls - SOS Button).
Should there be a Property Management Unit (concierge), a panic call may be made
by pressing the SOS button for 3 seconds.
Thepanic call isa special call madeto whichever PMUis configured toreceive alarms
and is responsible for receiving these types of calls.
Notes (SMILE monitor):
- This button flashes in the following instances:
• When the monitor has no network connection (two flashes per second).
• When a panic call is activated and a PMU is set up to receive alarms (one flash every two
seconds).
- In all other instances, it will remain switched off
Do not disturb mode
This function deactivates the monitor’s call sound.
Note:
- If you do not wish to hear the “beep” on receiving a message, this sound must be disabled.
See section: 3.1.1 Call Settings
Audio Activation and Hang-Up Button
When you receive a call (You have 30 seconds to answer before the device returns
to idle. During this time, the blue LED audio button will flash to let you know that the
call is waiting to be answered), press this button to talk to the visitor. The outdoor-
indoor audio channel is opened (the blue LED on the audio button lights up steadily
to indicate that you are in conversation with the outdoor panel and everything you say
will be heard on it), and the device is in hands-free mode.
Press to end the communication (the blue audio button LED will turn off again).
Communication will end automatically after 90 seconds, or whenever the button is
pressed.
Note:
-Audio pick-up and hang-upoperations can also be performedfrom the monitor touch screen,
see section: 5. CALLS.
Door Opening Button
When you are in communication (video / audio & video) with the Outdoor Panel,
pushing this button will activate the door release.
Note:
- Door opening operations can also be performed from the monitor touch screen, see section:
5. CALLS.
Icons Description

Page 9
LYNX Monitor
Message alert
When a new message is received, the message icon on the monitor lights up and a
"beep" is heard (this sound is optional and can be disabled).
If this message icon is lit, this indicates either a message, audio note, or missed
call. Text appears at the bottom of the screen telling the user what the notification
corresponds to.
Note:
- If you do not wish to hear the “beep” on receiving a message, this sound must be disabled.
See section: 3.1.1 Call Settings
Door open
When the door is opened from the monitor, the ‘door open’ LED will light up. If this
iconremains switched oncontinuously, thisindicates that thedoor has beenleft open.
Note:
- This LED icon does not exist on the SMILE monitor.
Current Alarm Status: Out (red icon).
This is the maximum level of security regarding the arming of alarms.
Zone arming depends on the configuration set up by the installer.
Current Alarm Status: Sleep (blue icon).
Intermediate level of security with regarding the arming of the alarms.
Night-time zone arming depends on the configuration set up by the installer.
Current Alarm Status: Home (green icon).
Thisisthe minimum security level,inwhich only technical alarms, suchasgas, smoke,
water, etc., are usually armed.
Notes:
-Changing toa higher-securityalarmstatus doesnot requirea PIN code to validate the action.
Changing to a lower status requires confirmation.
- For further details see section: 3.2.5 Alarm mode
- In the SMILE model, the alarm function is only available on EXTRA Smile Lynx Monitors.

Page 10
LYNX Monitor
The number of icons on the touch screen may vary depending on the features enabled in each
specific installation. The icons are displayed with a maximum number of 8 per screen.
This screen shows the available factory default icons.
On the screen there is a question mark which, when selected, will open a screen showing the icon and
explaining what it does.
To activate icons other than those available by
default, you must enter Optional Functions.
This may be done by selecting General Settings
and accessing the screen where the Installation
Settings option is located.
Press Installer Settings, enter the installer PIN
code (which is 4444 by default), press OK and
access the screen where the Optional Functions
option is located.
Press a function in order to enable it. This same
operation is used to disable a function, simply by
pressing.
Functions
enabled by
default
2 SCREEN DESIGN. START MENU
QR code on SMILE monitor

Page 11
LYNX Monitor
These are all the functions available on the monitor. When these functions are enabled, the screens will
be as shown. The installer must select the icons that they wish to activate, according to the requirements
of the installation. The descriptions and functions of these icons will be expanded upon in the various
chapters of the manual.
Press to return to the previous screen
Press to
enable
Note:
- As the screen shows a maximum of 8 icons when all functions have been added, new screens can be viewed
by sliding horizontally onto the display upon making a quick swipe to the right or left or by pressing the arrows
at the bottom of the screen.
Note:
- You can return to the start menu by pressing the intuitive icons that appear on the monitor, (such as arrows or
icons corresponding to the screen you are on), pressing the MENU button or simply waiting 30 seconds, after
which time the monitor will return to idle mode (Screen off).
Note:
- The position of the icons on the menu are organised
by their priority and availability.

Page 12
LYNX Monitor
Icons can be dragged in order to personalize the configuration of the start menu with the user’s most
frequently used functions, in any desired order.
2.1 STRUCTURE AND ARRANGEMENT OF FUNCTIONS
Do not disturb mode (3.2.1)
Call Property Management Unit (PMU) (3.2.3)
Camera Activated (3.2.2)
Receive messages (3.2.4)
Alarm mode (3.2.5)
Home Automation (3.2.6)
Audio Notes (3.2.7)
Call history (3.2.8)
Internal calls (3.2.9)
External calls (3.2.10)
IP cameras (3.2.11)
Default functions + Optional functions enabled

Page 13
LYNX Monitor
General Settings (3.1)
Ring settings (3.1.1)
Image visualisation (3.2.12)
Lift control (3.2.13)
Doormatic mode (3.2.14)
Send Message (3.2.15)
Timer (3.2.16)
Screen cleaning (3.2.17)
Contact list - Friendship request (3.2.18)
Mobility (3.2.19)
Relay control (3.2.20)
Background settings (3.1.2)
Language settings (3.1.3)
Picture settings (3.1.4)
International settings (date/time) (3.1.5)
User privacy settings (3.1.6)
Home-to-home call settings (3.1.7)
“Push to Talk”AUDIO mode (3.1.8)
F1 (3.2.21)
Induction loop (3.2.22)

Page 14
LYNX Monitor
Installer menu (3.1.9)
General Settings (3.1)
Monitor settings (3.1.9.1)
Delete all settings (reset) (3.1.9.2)
Lift control settings (3.1.9.3)
Optional functions(3.1.9.4)
Alarm settings (3.1.9.5)
Home Automation settings (3.1.9.6)
SD card menu (3.1.9.8)
Mobility settings (3.1.9.9)
Installer privacy settings (3.1.9.7)
Relay control (3.1.9.10)
Doorbell settings (3.1.9.11)
IP camera configuration (3.1.9.12)
VERY IMPORTANT Note:
- The Monitor has an integrated web server, allowing for configuration changes. See chapter 4. Configuring the
monitor from the web server

Page 15
LYNX Monitor
3 DESCRIPTION OF FUNCTIONS AVAILABLE ON MONITOR
You must first set the monitor’s language, date/time and address settings in order to configure / program
the remaining functions.
3.1 GENERAL SETTINGS
This function enables the configuration of various monitor settings. When you press the General
Settings icon, you will be taken to a screen containing various icons that control these settings.
These settings can also be configured and personalised by the user.
Note:
- Access to the General Settings menu can be restricted by a PIN code if desired. Access is unrestricted
by default. See chapter 3.1.6 Privacy settings (User).
3.1.1 General Settings. RING SETTINGS
The ring settings function allows you to:
- Select a ringtone and volume for each type of call:
• Calls from outdoor panels.
• Calls from private panels (single line call panel).
• Call from the Property Management Unit Guard.
• Call from the Property Management Unit Administrator.
• Home to home calls (property to property).
• In-Home calls (monitors within the same property).
•Door Bell
• Timer (alarm). (See option3.2.16 Timer).
- Select continuous ringtone:
• If this option is selected, the ringtone is played for 30 seconds.
• If this option is not selected, the ringtone is played only once.
- Select if you wish to hear a sound upon the arrival of:
• Received messages. New message alert.
•Openingofthedoorbyafamilymember.Family access alert. Viathe access control integrated
intothe system, the doorcan be opened bymeans of an identifierassociated with agivenuser.
This option can be selected to make the monitor to emit a sound when the door is opened
(this sound is hard-wired).
• Silent panic alarm via secondary external SOS button. (See option: 5. CALLS / Panic Call
(SOS button) / Silent Panic Alarm).

Page 16
LYNX Monitor
3.1.2 General Settings. BACKGROUND SETTINGS
The background settings function allows you to:
- Select the background colour and brightness of the screen.
- Select the audio level of the screen. Change the click volume.
3.1.3 General Settings. LANGUAGE SETTINGS
The language settings function allows you to select the desired language for the monitor. The
monitor’s factory default language is English.
3.1.4 General Settings. PICTURE SETTINGS
Thepicture settings functionallowsyoutoautomatically capture imagesfromeachcall.By factory
default, the monitor is set to capture images when a call has been missed: Missed calls only.
The automatic image setting options are:
- Always.
- Only Missed calls (factory default setting).
- Never.
Function enabled by default
Warning:
- Check the legal requirements for data protection and privacy as applicable to your territory, with regard
to taking and storing images of public highways.

Page 17
LYNX Monitor
3.1.5 General Settings. REGIONAL SETTINGS
The regional settings function allows you to not only change / update the date and time, but
also adapt to the appropriate local date format.
3.1.6 General Settings. PRIVACY SETTINGS (USER)
The privacy settings function allows you to lock some features of the monitor via a PIN code
(password), for want of privacy or for other reasons.
The monitor can be configured to request a PIN code to:
- Access the user configuration menu and / or
- Access messages in the inbox
Fromthisscreen,youcan also change the codes that areprogrammedintothemonitorby default:
- User PIN (default is: 1234)
- Alarm PIN (default is: 0000)
Press Installer Settings, enter the installer PIN code (which is 1234 by default), press OK and
access the screen where the Privacy Settings option is located. Press a function in order to
enable it. This same operation is used to disable a function, simply by pressing.
3.1.6.1 PIN required
a) User settings
If in Privacy Settings, PIN required is
selected:In User Settings, after pressing
General Settings, enter the installer PIN
code, which is 1234 by default (assuming
it has not been changed), press OK
and access the screen where the icons
corresponding to the various monitor
settings are located.

Page 18
LYNX Monitor
b) Messages Reading
If in Privacy Settings, PIN required is
selected: In Messages Reading, press
the Receive Messages icon which will
automatically open the PIN code request
screen.
SOS
Proceed with the messages as explained in: 3.2.4
Receive messages

Page 19
LYNX Monitor
3.1.6.2 Change PIN
a) User PIN
To change the user PIN. The default user
PIN is: 1234.
b) Alarm PIN
To change the Alarm PIN. The default
Alarm PIN is: 0000.

Page 20
LYNX Monitor
3.1.7 General Settings. HOME-TO-HOME CALL SETTINGS
Thehome-to-home settings function opensa screen that allowsyouto fill in themonitorlabels:
Tenant name: Identifies the house (i.e., the García family, name Marta Jover ...).
Note:
- All monitors belonging to the same property must have the same Name, Block and Unit.
Monitor tag: Describes its location (i.e. dining room, kitchen, living room...). Each monitor has
a different label. Since up to 8 monitors can be installed per property, the extension numbers
areas are as follows: 0...7.
This screen also displays the options to:
- Allow all incoming calls
- Only allow calls from friends See chapter: 3.2.18 Contact list - Friendship request.
For more general information on this option, see chapters3.2.9 Internal calls and 3.2.10 External
calls
Calls can be made from one monitor to another. There are 2 types of calls:
- Internal: when you make a call from your monitor to any other monitor in the same property.
- External: when you make a call between properties, i.e. to any monitor on the same circuit.
3.1.8 General Settings. “Push to Talk” AUDIO MODE
The “Push to Talk” audio mode lets you enable or disable this audio mode. This audio mode
works by pressing the corresponding button to speak, and releasing it to listen. See chapter: 5.
CALLS.
enabled
disabled