Fhiaba Integrated 599 Series User manual

33
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Index
Important Instructions
Important safety instructions
Children safety
Technical requirements
Appliance features and installation requirements
Installation niche features: Integrated
Installation niche features: Classic
Installation niche features: StandPlus
Installation niche features: X-Pro
Installation niche features: Country
Installation niche features: Brilliance-Integrated
Installation niche features: Brilliance-Classic
Preparing to install
Transport to installation site and unpacking
Electrical and Water connection
Levelling
Panels mounting
Decorative door and Bottom-Drawer panels layout
Decorative panels layout for Fridge with one Bottom-Drawer (1T/0T)
Decorative panels layout for Fridge Brilliance
Decorative panels layout for Fridge with two Bottom-Drawers (0H)
Decorative panels layout for Fridge with Glass door and one Bottom-Drawer (1T/0T)
Decorative panels layout for Fridge with Glass door Brilliance
Decorative panels layout for Fridge with Glass door and two Bottom-Drawers (0H)
Decorative panels layout for Fridge Column (0F)
Decorative panels layout for Fridge column with glass door (0F)
Panels Dimensions One Bottom - Drawer (1T/0T models)
Panels Dimensions Two Bottom - Drawers (0H models)
Panels Dimensions Column model (0F models)
Mounting the handles
Mounting panels to the door and the drawer
Installation
Built-in installation of single appliance
Built-in installation of two or more appliances
Free-standing installation two or more appliances
Completing the installation
Anti-tipping safety assembly
Mounting the handles on stainless front
Ventilation
Post installation control
Start Up

34
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Symbols used in the Guide
Important safely instruction
Children safety
If this appliance is replacing an existing appliance which
must be removed or disposed of, make sure that it does
not become a dangerous trap for children by cutting its
power supply cable and rendering it impossible to close
the door.
Use the same caution at the end of the lifespan of the
new appliance.
Note
Tips for the correct use of the
appliance
Warning
directions to prevent injury
Important
Directions to avoid appliance
damage
IMPORTANT
Dimensions in parentheses are in inches.
Weights in parentheses are in pounds.
Temperatures in parentheses are in Fahrenheit degrees.

35
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Appliance features and installation requirements
599 Series w: 599 mm (23 5/8”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”)
749 Series w: 749 mm (29 1/2”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”)
899 Series w: 899 mm (35 3/8”)/ h: 2050 mm (80 3/4”)/ d: 610 mm (24”)
599 Series w: 599 mm (23 5/8”)/ h: 2050 mm (80 3/4”))/ d: 635 mm (25”)
749 Series w: 749 mm (29 1/2”)/ h: 2050 mm (80 3/4”))/ d: 635 mm (25”)
899 Series w: 899 mm (35 3/8”)/ h: 2050 mm (80 3/4”))/ d: 635 mm (25”)
599 Series w: 599 mm (23 5/8”)/ h: 2120 mm (83 1/2”)/ d: 629 mm (24 3/4”)
749 Series w: 749 mm (29 1/2”)/ h: 2120 mm (83 1/2”)/ d: 629 mm (24 3/4”)
899 Series w: 899 mm (35 3/8”)/ h: 2120 mm (83 1/2”)/ d: 629 mm (24 3/4”)
599 Series w: 599 mm (23 5/8”)/ h: 2120 mm (84”)/ d: 635 mm (25”)
749 Series w: 749 mm (29 1/2”)/ h: 2120 mm (84”)/ d: 635 mm (25”)
899 Series w: 899 mm (35 3/8”)/ h: 2120 mm (84”)/ d: 635 mm (25”)
599 Series w: 599 mm (23 5/8”)/ h: 2050 mm (80 3/4”)/ d: 575 mm (22 5/8”)
749 Series w: 749 mm (29 1/2”)/ h: 2050 mm (80 3/4”)/ d: 575 mm (22 5/8”)
899 Series w: 899 mm (35 3/8”)/ h: 2050 mm (80 3/4”)/ d: 575 mm (22 5/8”)
599 Series w: 599 mm (23 5/8”)/ h: 2050 mm (80 3/4”))/ d: 600 mm (23 3/4”)
749 Series w: 749 mm (29 1/2”)/ h: 2050 mm (80 3/4”))/ d: 600 mm (23 3/4”)
899 Series w: 899 mm (35 3/8”)/ h: 2050 mm (80 3/4”))/ d: 600 mm (23 3/4”)
599 Series w: 650 mm (25 5/8”) / h: 2210 mm (87”)/ d: 800 mm (31 1/2”)
749 Series w: 800 mm (31 1/2”)/ h: 2210 mm (87”)/ d: 800 mm (31 1/2”)
899 Series w: 950 mm (37 3/8”) / h: 2210 mm (87”)/ d: 800 mm (31 1/2”)
599 Series w: 650 mm (25 5/8”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
749 Series w: 800 mm (31 1/2”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
899 Series w: 950 mm (37 3/8”) / h: 2260 mm (89”) / d: 800 mm (31 1/2”)
599 Series up to 230 kg (507 lb)
749 Series up to 275 kg (606 lb)
899 Series up to 295 kg (650 lb)
Europe Version: AC 220-240V 50 Hz / North America Version: 110V 60Hz
Europe Version: Schuko 16 A plug / North America Version: 15 A
from 0.05 MPa to 0.5 MPa (0.5 Bar - 5 Bar)
3/4” female attachment
Customized panels mounting Kit
Anti-tipping Kit (B04000200)
Lateral connecting kit (KCLIT/KCLIH)
4 mm (1/8”) allen wrench
Phillips head screwdriver
wood and percussion drill
2.5 mm (1/8”) bit for wood
8 mm (3/8”) bit for walls
17 mm (3/4”) wrench
Appliance dimensions
Integrated
Appliance dimensions
Classic
Appliance dimensions
StandPlus
Appliance dimensions
X-Pro / Country
Appliance dimensions
Brilliance-Integrated
Appliance dimensions
Brilliance-Classic
Appliance dimensions
Integrated / Classic
Appliance dimensions
StandPlus / X-Pro / Country
Weight with packaging
Voltage
Power supply cable
Potable water supply pressure
Water supply tube
Provided installation accessories
Additional equipment necessary

36
992 (39”)
S899: 1470 (57 7⁄8”)
S749: 1320 (52”) S599: 1170 (46”)
560 (22”)
610 (24”)
S899: 899 (35 3⁄8”)
S749: 749 (29 ½”)
S599: 599 (23 5⁄8”)
10 (3⁄8”)
105°
S899: 160 (6 3⁄8”)
S749: 125 (5”)
S599: 90 (3 ½”)
610 (24”)
560 (22”)
1293 (50 7⁄8” )
474 (18 5⁄8”)
231 (9
1⁄8”
) +
25 (1”)
500 (19 ¾”)
248 (9
¾”
)
+ 25 (1”) 20 (¾”)15 (5⁄8”)
721 (28 3⁄8”) +25 (1”)
2050 (80 ¾”) +25 (1”)
1T/0T
610 (24”)
560 (22”)
1808 (71 ¼” )
231 (9
1⁄8”
) +
25 (1”)
500 (19 ¾”)
233 (9
¼”
)
+ 25 (1”) 15 (5⁄8”)
2050 (80 ¾”) +25 (1”)
0F
2050 (80 ¾”) +25 (1”)
846 (33 ¼”) +25 (1”)
0H
610 (24”)
560 (22”)
500 (19 ¾”)
231 (9
1⁄8”
) +
25 (1”)
248 (9
¾”
)
+ 25 (1”) 15 (5⁄8”)
20 (¾”)10 (3⁄8”) 1168(46”)
330 (13”)
259 (10
¼”
)
min 2064 (81 ¼”)
A A
E W E W
140 (5 ½”) 140 (5 ½”)
100 (4”) 100 (4”)
899 900 (35½”)
599 600 (23¾”)
749 750 (295⁄8”)
A
E
W
2064 mm (81 1/4”)
S899: 900 mm (35 1/2”)
S749: 750 mm (29 5/8”)
S599: 600 mm (23 3/4”)
S899: 1470 mm (57 7/8”)
S749: 1320 mm (52”)
S599: 1170 mm (46”)
105°
S899: 899 mm (35 3/8”)
S749: 749 mm (29 1/2”)
S599: 599 mm (23 5/8”)
2050 mm (80 3/4”) + 25 mm (1”)
610 mm (24”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation niche features: Integrated Series
area to be left clear for the anti-tipping brackets
area to be left clear for the power supply cable
and water supply hose
Minimum Niche Height
Minimum Niche Width
Door Swing Clearance
Important: A 90° door opening is sufcient to allow
opening and full extraction of the inner drawers, even
if the appliance is installed directly adjacent to a wall.
Should an opening at 105° be desired, then the ap-
pliance should be positioned at the distance from the
wall described in gure.
area to be left clear for the anti-tipping brackets
area to be left clear for the power supply cable
and water supply hose
Minimum Niche Height
Minimum Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door (without panel)

37
A
E
W
2064 mm (81 1/4”)
KS899: 900 mm (35 1/2”)
KS749: 750 mm (29 5/8”)
KS599: 600 mm (23 3/4”)
KS899: 1470 mm (57 7/8”)
KS749: 1320 mm (52”)
KS599: 1170 mm (46”)
105°
KS899: 899 mm (35 3/8”)
KS749: 749 mm (29 1/2”)
KS599: 599 mm (23 5/8”)
2050 mm (80 3/4”) + 25 mm (1”)
635 mm (25”)
min 2064 (81 ¼”)
A A
EW E W
140 (5 ½”) 140 (5 ½”)
100 (4”) 100 (4”)
KS899: 900 (35 ½”)
KS599: 600 (23 ¾”)
KS749: 750 (29 5⁄8”)
635 (25”)
560 (22”)
1T/0T
693 (27 ¼”)
2050 (80 ¾”) +25 (1”)
1308 (51 ½”)587 (23 1⁄8”)146 (5 ¾”) + 25(1”) 9 ( 3⁄8”)
732 (28 7⁄8”)+25 (1”)
635 (25”)
560 (22”)
0F
693 (27 ¼”)
2050 (80 ¾”) +25 (1”)
1904 (75”)
146 (5
¾”) + 25(1”)
0H
635 (25”)
560 (22”)
693 (27 ¼”)
146 (5 ¾”) + 25(1”)
2050 (80 ¾”) +25 (1”)
857 (33 ¾”) +25 (1”)
1185 (46 5⁄8”)
342 (13 ½”)362 (14 ¼”)
9 ( 3⁄8”)6 ( ¼”)
KS899: 1470 (57 7⁄8”)
KS749: 1320 (52”) KS599: 1170 (46”)
560 (22”)
635 (25”)
KS899: 899 (35 3⁄8”)
KS749: 749 (29 ½”)
KS599: 599 (23 5⁄8”)
10 (3⁄8”)
105°
75 (3”)
58 (2 ¼”)
KS899: 230 (9”)
KS749: 195 (7 ¾”)
KS599: 160 (6 ¼”)
1016 (40”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Installation niche features: Classic Series
Important: A 90° door opening is sufcient to allow
opening and full extraction of the inner drawers, even
if the appliance is installed directly adjacent to a wall.
Should an opening at 105° be desired, then the ap-
pliance should be positioned at the distance from the
wall described in gure.
area to be left clear for the anti-tipping brackets
area to be left clear for the power supply cable
and water supply hose
Minimum Niche Height
Minimum Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door

38
A
E
W
2134 mm (84”)
MS899: 900 mm (35 1/2”)
MS749: 750 mm (29 5/8”)
MS599: 600 mm (23 3/4”)
MS899: 1470 mm (57 7/8”)
MS749: 1320 mm (52”)
MS599: 1170 mm (46”)
105°
MS899: 899 mm (35 3/8”)
MS749: 749 mm (29 1/2”)
MS599: 599 mm (23 5/8”)
2120 mm (83 1/2”) + 25 mm (1”)
629 mm (24 3/4”)
min 10
(3⁄8”)
min 50 (2”)
A A
E W E W
140 (5 ½”) 140 (5 ½”)
100 (4”) 100 (4”)
min 2134 (84”)
MS899: 900 (35 ½”)
MS599: 600 (23 ¾”)
MS749: 750 (29 5⁄8”)
560 (22”)
2120 (83 ½”) +25 (1”)
613 (24 1⁄8”)+25 (1”)
629 (24 ¾”)
615 (24 ¼”)
629 (24 ¾”)
615 (24 ¼”)
1T/0T
2120 (83 ½”) +25 (1”)
0H
666 (26 ¼”)
485 (19 1⁄8”)1296 (50”)
195 (7 5⁄8”)
8 (3⁄8”)8 (3⁄8”)
128 (5)
+ 25 (1”
)
128 (5)
+ 25 (1”)
195 (7 5⁄8”)
8 (3⁄8”)8 (3⁄8”)
560 (22”)
666 (26 ¼”)
1170 (46”)
343 (13 ½”)
262 (10 ¼”)
6 ( ¼”)
749 (29 ½”) + 25 (1”)
1010 (39 ¾”)
560 (22”)
MS899: 899 (35 3⁄8”)
MS749: 749 (29 ½”)
MS599: 599 (23 5⁄8”)
10 (
3⁄8
”)
105°
629 (24 ¾”)
37 (1 ½”)
69 (2 ¾”)
MS899: 1470 (57 7⁄8”)
MS749: 1320 (52”
)
MS599: 1170 (46”
)
MS899: 230 (9”)
MS749: 195 (7 ¾”)
MS599: 160 (6 ¼”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation niche features: StandPlus Series
Important: A 90° door opening is sufcient to allow
opening and full extraction of the inner drawers, even
if the appliance is installed directly adjacent to a wall.
Should an opening at 105° be desired, then the ap-
pliance should be positioned at the distance from the
wall described in gure.
area to be left clear for the anti-tipping brackets
area to be left clear for the power supply cable
and water supply hose
Minimum Niche Height
Minimum Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door
Important: If the units are to be installed inside a ni-
che or within an enclosed structure, it is necessary to
design a ventilation shaft at the back of the niche to
assure proper ventilation at the back of the unit.

39
min 10 (3⁄8”)
min 50 (2”)
A
E
W
2134 mm (84”)
XS899: 900 mm (35 1/2”)
XS749: 750 mm (29 5/8”)
XS599: 600 mm (23 3/4”)
XS899: 1470 mm (57 7/8”)
XS749: 1320 mm (52”)
XS599: 1170 mm (46”)
105°
XS899: 899 mm (35 3/8”)
XS749: 749 mm (29 1/2”)
XS599: 599 mm (23 5/8”)
2120 mm (83 1/2”) + 25 mm (1”)
635 mm (25 ”)
A A
E W E W
140 (5 ½”) 140 (5 ½”)
100 (4”) 100 (4”)
min 2134 (84”)
XS899: 900 (35 ½”)
XS599: 600 (23 ¾”)
XS749: 750 (29 5⁄8”)
560 (22”)
2120 (83 ½”) +25 (1”)
613 (24 1⁄8”)+25 (1”)
2120 (83 ½”) +25 (1”)
635 (25”)
693 (27 ¼”)
516 (20 3⁄8”)1296 (50”)
195 (7 5⁄8”)
8 (3⁄8”)8 (3⁄8”)
195 (7 5⁄8”)
8 (3⁄8”)8 (3⁄8”)
749 (29 ½”) + 25 (1”
)
1170 (46”)
343 (13 ½”)
293
(11 ½”)
6 ( ¼”)
1T/0T
0H
97 (3 7⁄8”)
+ 25 (1”)
97 (3 7⁄8”)
+ 25 (1”)
1016 (40”)
XS899: 1470 (57 7⁄8”)
XS749: 1320 (52”) XS599: 1170 (46”)
560 (22”)
75 (3”)
XS899: 899 (35 5⁄8”)
XS749: 749 (29 ½”)
XS599: 599 (23 5⁄8”)
10 (3⁄8”)58 (2 ¼”)
105°
635 (25”)
XS899: 230 (9”)
XS749: 195 (7 ¾”)
XS599: 160 (6 ¼”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Installation niche features: X-Pro Series
Important: A 90° door opening is sufcient to allow
opening and full extraction of the inner drawers, even
if the appliance is installed directly adjacent to a wall.
Should an opening at 105° be desired, then the ap-
pliance should be positioned at the distance from the
wall described in gure.
area to be left clear for the anti-tipping brackets
area to be left clear for the power supply cable
and water supply hose
Minimum Niche Height
Minimum Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door
Important: If the units are to be installed inside a ni-
che or within an enclosed structure, it is necessary to
design a ventilation shaft at the back of the niche to
assure proper ventilation at the back of the unit.

40
min 10 (3⁄8”)
min 50 (2”)
A
E
W
2134 mm (84”)
AS899: 900 mm (35 1/2”)
AS749: 750 mm (29 5/8”)
AS599: 600 mm (23 3/4”)
AS899: 1470 mm (57 7/8”)
AS749: 1320 mm (52”)
AS599: 1170 mm (46”)
105°
AS899: 887 mm (35")
AS749: 737 mm (29")
AS599: 587 mm (23 1/8")
2120 mm (83 1/2”) + 25 mm (1”)
635 mm (25 ”)
A A
E W E W
140 (5 ½”) 140 (5 ½”)
100 (4”) 100 (4”)
min 2134 (84”)
AS899: 900 (35 ½”)
AS599: 600 (23 ¾”)
AS749: 750 (29 5⁄8”)
560 (22”)
2120 (83 ½”) +25 (1”)
613 (24 1⁄8”)+25 (1”)
635 (25”)
695 (27 ¼”)
485 (19 1⁄8”)1296 (50”)
195 (7 5⁄8”)
8 (3⁄8”)8 (3⁄8”)
1T/0T
128 (5)
+ 25 (1”)
1016 (40”)
AS899: 1470 (57 7⁄8”)
AS749: 1320 (52”) AS599: 1170 (46”)
560 (22”)
75 (3”)
AS899: 887 (35”)
AS749: 737 (29”)
AS599: 587 (23 1⁄8”)
10 (3⁄8”)60 (2 ¼”)
105°
635 (25”)
AS899: 230 (9”)
AS749: 195 (7 ¾”)
AS599: 160 (6 ¼”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation niche features: Country Series
Important: A 90° door opening is sufcient to allow
opening and full extraction of the inner drawers, even
if the appliance is installed directly adjacent to a wall.
Should an opening at 105° be desired, then the ap-
pliance should be positioned at the distance from the
wall described in gure.
area to be left clear for the anti-tipping brackets
area to be left clear for the power supply cable
and water supply hose
Minimum Niche Height
Minimum Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door

41
A A
E W E W
140 (5 ½”) 140 (5 ½”)
100 (4”) 100 (4”)
min 2064 (81 ¼”)
BI899: 900 (35 ½”)
BI599: 600 (23 ¾”)
BI749: 750 (29 5⁄8”)
575 (22 5⁄8”)
525 (20 5⁄8”)
1293 (50 7⁄8” )
474 (18 5⁄8”)
231 (9
1⁄8”
) +
25 (1”)
465 (18 3⁄8”)
248 (9
¾”
)
+ 25 (1”) 20 (¾”)15 (5⁄8”)
721 (28 3⁄8”) +25 (1”)
2050 (80 ¾”) +25 (1”)
0T
947 (37 ¼”)
BI899: 1435 (56 ½”)
BI749: 1285 (50 5⁄8”)
BI599: 1135 (44 ¾”)
525 (20 5⁄8”)
575 (22 5⁄8”)
BI899: 899 (35 3⁄8”)
BI749: 749 (29 ½”)
BI599: 599 (23 5⁄8”)
10 (
3⁄8
”)
105°
BI899: 160 (6 3⁄8”)
BI749: 125 (5”)
BI599: 90 (3 ½”)
A
E
W
2064 mm (81 1/4”)
BI899: 900 mm (35 1/2”)
BI749: 750 mm (29 5/8”)
BI599: 600 mm (23 3/4”)
BI899: 1435 mm (56 1/2” in)
BI749: 1285 mm (50 5/8” in)
BI599: 1135 mm (44 3/4” in)
105°
BI899: 899 mm (35 3/8”)
BI749: 749 mm (29 1/2”)
BI599: 599 mm (23 5/8”)
2050 mm (80 3/4”) + 25 mm (1”)
575 mm (22 5/8” in)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Installation niche features: Brilliance-Integrated Series
Important: A 90° door opening is sufcient to allow
opening and full extraction of the inner drawers, even
if the appliance is installed directly adjacent to a wall.
Should an opening at 105° be desired, then the ap-
pliance should be positioned at the distance from the
wall described in gure.
area to be left clear for the anti-tipping brackets
area to be left clear for the power supply cable
and water supply hose
Minimum Niche Height
Minimum Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door (without panel)

42
A
E
W
2064 mm (81 1/4”)
BKI899: 900 mm (35 1/2”)
BKI749: 750 mm (29 5/8”)
BKI599: 600 mm (23 3/4”)
BKI899: 1435 mm (56 1/2” in)
BKI749: 1285 mm (50 5/8” in)
BKI599: 1135 mm (44 3/4” in)
105°
BKI899: 899 mm (35 3/8”)
BKI749: 749 mm (29 1/2”)
BKI599: 599 mm (23 5/8”)
2050 mm (80 3/4”) + 25 mm (1”)
600 mm (23 3/4” in)
A A
E W E W
140 (5 ½”) 140 (5 ½”)
100 (4”) 100 (4”)
min 2064 (81
¼”)
BKI899: 900 (35 ½”)
BKI599: 600 (23 ¾”)
BKI749: 750 (29 5⁄8”)
600 (23 ¾”)
525 (20 5⁄8”)
0T
693 (27 ¼”)
2050 (80 ¾”) +25 (1”)
1308 (51 ½”)587 (23 1⁄8”)
146 (5
¾”) + 25(1”) 9 ( 3⁄8”)
732 (28 7⁄8”)+25 (1”)
BKI899: 1435 (56 ½”)
BKI749: 1285 (50
5⁄8”)
BKI599: 1135 (44
¾”)
525 (20 5⁄8”)
600 (23 ¾”)
BKI899: 899 (35 3⁄8”)
BKI749: 749 (29 ½”)
BKI599: 599 (23 5⁄8”)
10 (3⁄8”)
105°
75 (3”)
58 (2 ¼”)
BKI899: 230 (9”)
BKI749: 195 (7 ¾”)
BKI599: 160 (6 ¼”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation niche features: Brilliance-Classic Series
Important: A 90° door opening is sufcient to allow
opening and full extraction of the inner drawers, even
if the appliance is installed directly adjacent to a wall.
Should an opening at 105° be desired, then the ap-
pliance should be positioned at the distance from the
wall described in gure.
area to be left clear for the anti-tipping brackets
area to be left clear for the power supply cable
and water supply hose
Minimum Niche Height
Minimum Niche Width
Door Swing Clearance
Door Opening Angle
Width
Height
Depth with door

EW
E W
EW
E W
43
1
4
1
2
3
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
The appliance is very heavy.
Take maximum care during handling to avoid injury.
The appliance should always be transported in an erect
position.
Avoid at all costs leaning it on its front side.
Preparing the installation
Transport to installation site and unpacking
Since this is a large and heavy appliance, before trans-
porting the appliance, check the access to the location
where it will be installed (door size, manoeuvring space in
stairwells, etc.).
The appliance is attached to the base of the packaging
(pallet) through four bolts which can be removed using a
17 mm (3/4”) wrench.
It is recommended to use a manual transporting device to
move the appliance to the installation site, and only at this
point to remove the base of the packaging.
The appliance should always be transported in an erect
position.
If this is not possible, transport the appliance laying on its
rear side.
Once at the installation site, the appliance, which is
equipped with four wheels, can be taken off the pallet and
positioned in the installation area.
Operate as follows:
Take off the four bolts 1securing the appliance to the
pallet by means of a 17 mm (3/4”) open spanner.
Remove the xing brackets 3and 4.
To remove the front xing bracket 3, unscrew
for one or two turns the rear wheel adjusting bolt 2
by means of a 13 mm (1/2”) box spanner, avoiding
too much strenght while thightening the nut, which
could damage the leveling feet adjusting system.
From the back of the unit and by means of a suitable,
high duty hand trolley, take off the appliance and place
it on the oor.
Be very careful to avoid any damage to oors. Delicate oors
should be protected with plywood, hard cardboard or similar
material panels.
Electrical and Water connection
A Schuko 16 A socket with an efcient grounding should
be made available for the electrical mains connection, as
well as an omnipolar
switch which can easily be reached when the appliance
is installed.
To connect to the water supply system (for appliances
equipped with ice makers) a tap with a male 3/4” connec-
tion should be provided, which must also be easily acces-
sible once the appliance is installed.
The appliance is provided with a water supply hose and
seal kit which is suitable for high water pressure and com-
plies the Food Regulations.
The water lter cartridge, which is provided with the appli-
ance, should be installed according to the accompanying
instructions.
Use only the new hose and the new gaskets which are sup-
plied with the appliance. Discard any hose and gasket
which may have already been installed.
Electrical cord length: 2,0 mt (78 3/4”)
Water connection line length: 2,5 mt (98 3/8”)
Do not use extension cords or adapters.
Once the appliance has been connected to the water system,
turn the Ice Maker off (touch the button on control panel to
switch it off) before the main water is shut off.
The appliance should be connected only to a drinkable
water supply system.
The Built-in Fhiaba lter cannot make it safe to drink any
water which is not suitable for human consumption.

2
1
2
1
44
E
W
E
W
1
2
1
2
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Energy: Alternatives and Home Automation
If energy is supplied through an alternative energy power
source (solar, geothermal, etc..) or if home automation
systems are installed, it is necessary to install the Alterna-
tive Energy Kit to integrate the unit into the power grid.
Electrical and water supply behind the unit
Integrated and Classic Series
Integrated and Classic Series
StandPlus, X-Pro and
Country Series
StandPlus, X-Pro and Country Series
Water connection
Electrical connection
Operate as follows:
Unwind the electric cable and connect it directly to the
wall socket.
Make sure the appliance is in the Stand-by condition and
that all lights are off; should it be not so press the Unit but-
ton to switch it off.
Fit one end of the water hose onto the connector at the
appliance’s back 1.
Fit the other end of the hose to the water tap, use the
gaskets provided in the Owner’s Kit 2.
Back of appliance
Operate as follows:
Unwind the electric cable and connect it directly to the
wall socket.
Make sure the appliance is in the Stand-by condition and
that all ights are off; should it be not so press the Unit button
to switch it off.
Connect the water line to the threaded connection at the
base of the unit, as in gure 1.
Fit the other end of the hose to the water tap, use the gas-
kets provided in the Owner’s Kit 2.
Back of appliance
Front of appliance
Water connection
Electrical connection
Adjust the appliance level by means of the front levelling
feet and the rear adjustable wheels.
Operate as follows:
After removing the bottom plinth or grille (it is kept in
position by magnets), adjust the height of the levelling feet
1by means of a 17 mm (3/4”) open spanner.
Then adjust the height of the rear wheels by turning the
front adjusting bolts 2clockwise or anticlockwise as it may
be required.
Remount the bottom plinth or grille.
Levelling

45
1
2
3
7
8
4
56
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Decorative door and bottom-
drawer panels layout
The dimensions of the panels are indicated in the table
and drawings on next pages.
Nevertheless, according to the requirements for aligning
with other kitchen structures, the door panel can be high-
er than the upper edge of the refrigerator door, and the
drawer panel can be lower than the edge of the drawer.
The panels must be mounted using special braces which
attach to adjustable devices provided on the door and
drawer and with brackets that anchor and adjust the
panel’s vertical direction.
Braces, brackets and fixing screws are provided with the
appliance and must be applied to the panel as indicat-
ed.
Operate as follows:
To prepare the panels to be mounted on the appliance,
follow these steps, working on the back of the panel.
Door Panel
Trace, a line dividing the panel width in half 1.
Starting form the Bottom edge of the panel, mark the
positioning of the brackets 2.
Following the corresponding table, mark the external
and then the internal hole 3.
Position the brackets on each set of marks to make sure
they are aligned 4, then drill holes through the panel
(pay close attention to the panel’s thickness) 5.
Screw the brackets in place 6.
Drawer Panel
When preparing the Drawer Panel, follow the same in-
structions as per the door panel, but make sure measure-
ments are taken starting from the top edge 7. The sup-
port bracket faces the opposite way 8(note imgs 4 and
8).
Integrated Series

46
D E
D E
A
B C
F G
13 (½”)
13 (½”)
34 (1 3⁄8”)
34 (1 3⁄8”)
1285 (505⁄8”)
1163 (45 ¾”)
660 (26”)
157 (6 ¼”)
min 1320 (52”)
max 635 (25”
)
507,5 (20”)
382 (15 1⁄8”)
100 (4”)
A897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”)
355,5 (14”)
355,5 (14”)
279 (11”)
279 (11”)
205 (8 1⁄8”)
205 (8 1⁄8”)261 (10 ¼”)
261 (10 ¼”)
187 (7 3⁄8”)
187 (7 3⁄8”)
111 (4 3⁄8”)
111 (4 3⁄8”)
418 (16 ½”)
418 (16 ½”)
343 (13 ½”)
343 (13 ½”)
276,5 (10 7⁄8”)
276,5 (10 7⁄8”)386 (15 ¼”)
386 (15 ¼”)
311 (12 ¼”)
311 (12 ¼”)
236,5 (9 3⁄8”)
236,5 (9 3⁄8”)
B
C
D
E
354,5 (14”) 354,5 (14”) 279,5 (11”) 279,5 (11”) 203,5(8”)
597 (23 ½”)
203,5(8”)F / G
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Decorative panels layout for Fridge with one Bottom-Drawer (1T/0T)
Series 899
Hinge Left Hinge Left Hinge Left
Hinge Right Hinge Right Hinge Right
Series 749 Series 599
Holes positions

47
A897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”)
417 (16 3⁄8”)
417 (16 3⁄8”)
342 (13 ½”)
342 (13 ½”)
276,5 (10 7⁄8”)
276,5 (10 7⁄8”)417 (16 3⁄8”)
417 (16 3⁄8”)
342 (13 ½”)
342 (13 ½”)
268 (11 ¼”)
268 (11 ¼”)
354,5 (14”) 279,5(11”) 203,5 (8”)354,5 (14”) 279,5(11”) 203,5 (8”)
B
C
D
597 (23 ½”)
A
BB
A
BB
C C
13 (½”)
34 (1 3⁄8”)
6,5 (¼”)6,5 (¼”)
34 (1 3⁄8”)
1273 (501⁄8”)
1163 (45 ¾”)
660 (26”)
157 (6 ¼”)
min 1390 (54 ¾”)
max 635 (25”
)
507.5 (20”)
382 (15 1⁄8”)
100 (4”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Decorative panels layout for Fridge Brilliance
Series 899
Hinge Left Hinge Left Hinge Left
Hinge Right Hinge Right Hinge Right
Series 749 Series 599
Holes positions

48
D E
A
BC
F G
D E
13 (½”)
13 (½”)
34 (1 3⁄8”)
min 1195 (47”)
1160 (45 5⁄8”)
1044 (41 1⁄8”)
600 (23 5⁄8”)
268 (10 ½”)
292,5 (11 ½”)
183 (7 ¼”)
73 (2 7⁄8”)66 (2 5⁄8”)157 (6 ¼”)
337 (13
¼”
)
max 415 (16
3⁄8”)
A897 (35 ¼”) 897 (35 ¼”) 747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”)
355,5 (14”)
355,5 (14”)
279 (11”)
279 (11”)
205 (8 1⁄8”)
205 (8 1⁄8”)261 (10 ¼”)
261 (10 ¼”)
187 (7 3⁄8”)
187 (7 3⁄8”)
111 (4 3⁄8”)
111 (4 3⁄8”)
418 (16 ½”)
418 (16 ½”)
343 (13 ½”)
343 (13 ½”)
276,5 (10 7⁄8”)
276,5 (10 7⁄8”)386 (15 ¼”)
386 (15 ¼”)
311 (12 ¼”)
311 (12 ¼”)
236,5 (9 3⁄8”)
236,5 (9 3⁄8”)
B
C
D
E
354,5 (14”) 354,5 (14”) 279,5 (11”) 279,5 (11”) 203,5(8”)
597 (23 ½”)
203,5(8”)F / G
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Decorative panels layout for Fridge with two Bottom-Drawers (0H)
Holes positions
Series 899
Hinge Left Hinge Left Hinge Left
Hinge Right Hinge Right Hinge Right
Series 749 Series 599

49
H I
D E
A
F G
1286 (50 5⁄8”)
6,5 (¼”)
6,5 (¼”)
1152,5 (45 3⁄8”)
650,5 (13 5⁄8”)
148,5 (5 7⁄8”)
13 (½”)
34 (1 3⁄8”)
34 (1 3⁄8”)
min 1320 (52”)
max 635 (25”
)
507,5 (20”)
382 (15 1⁄8”)
100 (4”)
899:627 (24 5⁄8”)
749:477 (18 ¾”)
599: 327 (12 7⁄8”)
1075 (42 3⁄8”)
min 130 (5 1⁄8”
)
115 (4 ½”)
135 (5
3⁄8”)135 (5 3⁄8”
)
A
H
I
F / G
897 (35 ¼”) 897 (35 ¼”)747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”)
354,5 (14”) 354,5 (14”) 279,5 (11”) 279,5 (11”) 203,5(8”) 203,5(8”)
412 (16 ¼”)
412 (16 ¼”)
337 (13 ¼”)
337 (13 ¼”)
270,5 (10 5⁄8”)
270,5 (10 5⁄8”)380 (15”)
380 (15”)
305 (12”)
305 (12”)
230,5 (9 1⁄8”)
230,5 (9 1⁄8”)
418 (16 ½”)
418 (16 ½”)
343 (13 ½”)
343 (13 ½”)
276,5 (10 7⁄8”)
276,5 (10 7⁄8”)386 (15 ¼”)
386 (15 ¼”)
311 (12 ¼”)
311 (12 ¼”)
236,5 (9 3⁄8”)
236,5 (9 3⁄8”)
D
E
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Decorative panels layout for Fridge with glass door and one Bottom-Drawer (1T/0T)
Holes positionsDoor window dimensions
Series 899
Hinge Left Hinge Left Hinge Left
Hinge Right Hinge Right Hinge Right
Series 749 Series 599

50
B C
B B
A
D D
1273 (50 1⁄8”)
6,5 (¼”)
6,5 (¼”)
1152,5 (45 3⁄8”)
650,5 (13 5⁄8”)
148,5 (5 7⁄8”)
13 (½”)
34 (1 3⁄8”)
34 (1 3⁄8”)
min 1320 (52”)
max 635 (25”)
507,5 (20”)
382 (15 1⁄8”)
100 (4”)
599: 327 (12 7⁄8”)
1075 (42 3⁄8”)
min 130 (5 1⁄8”
)
115 (4 ½”)
135 (5
3⁄8”)135 (5 3⁄8”
)
A
D
597 (23 ½”) 597 (23 ½”)
203,5(8”) 203,5(8”)
276,5 (10 7⁄8”)
276,5 (10 7⁄8”)268 (10 ½”)
268 (10 ½”)
B
C
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Decorative panels layout for Fridge with glass door Brilliance
Holes positionsDoor window dimensions
Series 599
Hinge Left Hinge Right

51
950 (37 3⁄8”)
899:627 (24 ¾”)
749:477 (18 ¾”)
599: 327 (12 7⁄8”)
115 (4 ½”)
135 (5
3⁄8”)135 (5 3⁄8”)
min 130 (5 1⁄8”)
A
H
I
F / G
897 (35 ¼”) 897 (35 ¼”)747 (29 3⁄8”) 747 (29 3⁄8”) 597 (23 ½”) 597 (23 ½”)
354,5 (14”) 354,5 (14”) 279,5 (11”) 279,5 (11”) 203,5(8”) 203,5(8”)
412 (16 ¼”)
412 (16 ¼”)
337 (13 ¼”)
337 (13 ¼”)
270,5 (10 5⁄8”)
270,5 (10 5⁄8”)380 (15”)
380 (15”)
305 (12”)
305 (12”)
230,5 (9 1⁄8”)
230,5 (9 1⁄8”)
418 (16 ½”)
418 (16 ½”)
343 (13 ½”)
343 (13 ½”)
276,5 (10 7⁄8”)
276,5 (10 7⁄8”)386 (15 ¼”)
386 (15 ¼”)
311 (12 ¼”)
311 (12 ¼”)
236,5 (9 3⁄8”)
236,5 (9 3⁄8”)
D
E
FG
D E
6,5 (¼”)
6,5 (¼”)
H I
A
1161 (45 ¾”)
1026,7 (40 3⁄8”)
588 (23 1⁄8”)
149,5 (5 7⁄8”)
13 (½”)
34 (1 3⁄8”)
min 1195 (47”)
268 (10 ½”)
292,5 (11 ½”)
183 (7 ¼”)
73 (2 7⁄8”)66 (2 5⁄8”)
337 (13 ¼”)
m 415 (16
3⁄8”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Installation Guide
EN
Decorative panels layout for Fridge with glass door and two Bottom-Drawers (0H)
Holes positionsDoor window dimensions
Hinge Left Hinge Left
Hinge Right Hinge Right

52
1
A897 (35 ¼”)
418 (16 ½”)
418 (16 ½”)
747 (29 3⁄8”)
343 (13 ½”)
343 (13 ½”)
597 (23 ½”) 597 (23 ½”)
276,5 (10 7⁄8”)
276,5 (10 7⁄8”)268 (10 ½”)
268 (10 ½”)
B
C
13 (½”)
min 1863 (73 3⁄8”)
95 (3 ¾”)
1201,5 (47 3⁄8”)
620,5 (24 ½”)
1727 (68”)
47 (1 7⁄8”)
B C
A
34 (1 3⁄8”)34 (1 3⁄8”)
www.fhiaba.com · [email protected] · Tel [phone] · Fax [phone]
Decorative panels layout for Fridge Column (0F)
Holes positions
Series 899
Hinge Left Hinge Right
Series 749 Series 599