Fhiaba Integrated Series User manual

USER MANUAL

1
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Index
Important directions for safety and the environment
For your safety
Caring for the environment
Installation
Installation
Connection to the electrical power supply
Connection to the water system
Before starting
Know your appliance
Main features
Main components
Electronic Control
Main control panel and Fresco control
Appliance switching on and off
Switching on and off
How to adjust the temperature for different requirements
Ice Maker activation
Information and malfunction messages on the display
Settings and Special Functions
Customization and language settings
Special functions activated through the Fhiaba Access Menu
Basic settings of the Fhiaba Access Menu
Internal Layout
Internal Layout (positioning, adjustment, removal)
Activation and use of the Ice Maker
Activation and use of the Ice Maker
Water Filter
Lighting
Lighting
Food Conservation
General directions
How to maintain good food quality
Recommendations for conserving fresh food
Recommendations for conserving frozen food
Recommended times for food conservation
Care and Cleaning
Care and Cleaning
Condenser cleaning
Internal cleaning
Troubleshooting Guide
Troubleshooting Guide
Malfunction messages appearing on the display
Before calling for service
Before calling for service
Fhiaba Access Menu Map
Functions
Setting
Page
1
1.1
1.2
2
2.1
2.2
2.3
3
3.1
3.2
3.3
3.4
3.5
4
4.1
4.2
4.3
4.4
5
5.1
5.2
5.3
6
6.1
7
7.1
7.2
8
8.1
9
9.1
9.2
9.3
9.4
10
11
11.1
11.2
11.3
12
12.1
12.2
13
13.1
14
14.1
14.2
2
3
4
8
10
15
17
18
19
22
23
24
26
27

2
1
1.1
1.2
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Pay special attention to correct disposal procedure for all the packag-
ing materials.
The appliance must not be disposed of with urban waste. Contact lo-
cal waste disposal centers for on how to dispose of recyclable waste.
Prior to disposal, cut the power supply cord and make it impossible
to close the door.
During disposal, avoid damage to the refrigeration circuit.
The appliance does not contain hazardous substances for the atmos-
pheric ozone layer, neither in the refrigeration circuit nor in the insulation.
Notes
Recommendations for correct
use of the appliance
For your safety
Caring for the environment
Important
Directions for avoiding
appliance damage
Warning
Indications for avoiding injury
to people
If this appliance is replacing an existing appliance which must be re-
moved or disposed of, make sure that it does not become a dangerous
trap for children by cutting its power supply cable and rendering it impos-
sible to close the door. Use the same caution at the end of the lifespan
of the new appliance.
This appliance is designed to refrigerate beverages and foods and is
destined for domestic use.
The appliance must be installed by following the instructions in the In-
stallation Guide, particular care should be taken not to obstruct the vent
openings of the appliance and of the built-in units.
The appliance features a concentrated lighting system with LED lamps.
Do not stear into these lamps when they are on to avoid possible eyesight
damage. This warning is also contained on the label attached to the in-
side of the refrigerator door.
When the freezer is functioning do not touch the inner surfaces in stain-
less steel with wet or damp hands, since skin may stick to the very cold
surfaces.
Do not use any type of electrical equipment inside of the food conser-
vation compartments.
When positioning the shelves, do not place fingers in the shelf slide
guides.
Do not position containers of flammable liquids near the appliance.
Completely switch off the appliance and unplug the power supply
cable during cleaning operations. If the plug is not easily reached, it is a
good idea to disconnect the omnipolar switch that controls the socket
that the appliance is connected to.
The packaging parts can be dangerous for children: do not allow chil-
dren to play with the plastic bags, plastic film or Styrofoam.
Any repairs must be performed by a qualified Fhiaba Service technician.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or lack of experience and knowledge un-
less they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
Important directions for safety and the environment

3
2
2.1
2.2
2.3
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Make sure that installation is performed correctly, adhering to all direc-
tions in the specific installation manual provided with the appliance.
Installation
Connection to the electrical power supply
The appliance is equipped with a Schuko type 16A plug and must be
connected to the electrical power supply through a corresponding
Schuko socket.
Do not use extension cords and/or multiple adapters for the power
supply connection.
The models provided with Ice Maker require a connection to the do-
mestic water supply system. This can be executed through the pro-
vided water hose with 3/4” threading.
The system pressure must be between 0.05 MPa and 0.5 MPa (between
0.5 Bar and 5 Bar).
Differents pressures can cause malfunctions or leaks in the water sys-
tem. The appliance should be supplied only with drinkable water.
Do not use extension cords and/or multiple
adapters for the power supply connection.
The appliance should be supplied only with
drinkable water.
Make sure that installation is performed cor-
rectly, according to all of the directions in
the specific installation manual provided
with the appliance.
Connection to the water system
Installation

4
3
3.1
3.2
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Before starting
Know your appliance
Congratulations for having purchased your new Fhiaba:
from now on you can use our innovative conservation sys-
tem, which will allow you to keep all of your food in the
best way possible.
This manual will answer most of your questions about the
product’s features. Should you require further information,
please check our website
www.fhiaba.com
or write us an e-mail at
[email protected].
Before calling, write down the model type and serial
number which are available on the warranty certificate
and on the rating plate located on the bottom left-hand
corner of the appliance, behind the bottom drawer and
any messages which may have appeared on the display.
Exclusive design by Giugiaro
The Fhiaba TriMode refrigeration system and the efficient
separation of internal compartments ensures maximum
freshness and offers excellent conservation of foods in the
three compartments: refrigerator, Fresco and freezer
It is also possible, should there be a need, to further in-
crease the flexibility of the appliance by making the freezer
compartment operate as a refrigerator or as a Fresco com-
partment
The Fresco compartment has a low temperature and con-
trolled humidity, providing excellent conservation in maxi-
mum safety conditions for fresh foods
Electronic control guarantees constant temperature and
humidity levels set by the user
An interactive menu (Fhiaba Access) allows customized
management of appliance functions and the visualization
of functioning messages
Main features
Power save features to reduce consumption during vaca-
tion periods
Ample drawers with Soft self-closing systems in the Fresco area
Ice Maker for automatic ice production in the desired size
Easily replaceable water filter located inside the refrigerator
Patented sliding shelf system, with shelves that can be po-
sitioned at any level inside of the refrigerator without having
to be removed
Stainless steel surface both inside and outside, with fine alu-
minum trim
Patented hinge system that permits automatic door closing
External drawers with to self-closing system
Localized lighting with LEDs
Anti-tipping system by means of wall mounting brackets

5
3
3.3
1
1
1
8
9
9
9
9
10
10
10
10
11
11
11
11
12
12
12
12
13
13
13
13
14
14
14
14
15
15
15
15
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
6
6
6
6
7
7
7
8
8
7
8
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Before starting
Main components
Single drawer model
1Stainless steel structure with
aluminum trim
2Control panel with Fhiaba
Access
3Water Filter
4Patented shelf positioning
system
5Control panel, Fresco area
6Fresco compartment with
controlled humidity
or “Low Temp”
7Automatic icemaker
8Double refrigeration system
9Temperature display
10 Sound signals
11 Vacation function
12 Spacious door shelves
13 Innovative lighting
14 Automatic door and
drawer closure
15 Frezer compartment that
can be transformed into
a refrigerator or Fresco
compartment
(TriMode function)
Integrated Series
StandPlus Series
Professional Series
Classic Series

6
3
3.3
16
7
7
7
8
8
8
9
9
9
10
10
10
11
11
11
12
12
12
2
2
2
1
3
3
3
4
4
4
5
5
5
6
6
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Before starting
Two drawer model
1Stainless steel structure with
aluminum trim
2Control panel with Fhiaba
Access
3Water Filter
4Patented shelf positioning
system
5Automatic icemaker
6Double refrigeration system
7Temperature display
8Sound signals
9Vacation function
10 Spacious door shelves
11 Innovative lighting
12 Automatic door and
drawer closure
Main components
Integrated Series
StandPlus Series
Professional Series

7
3
3.3
3.3
Componenti principali
Componenti principali
3.5
3.4
1234 5 67 9 108
1Unit
2Fridge
3Fhiaba
Access
4Up/down
Fridge
5Display
6
Up/Down
Freezer
(TriMode)
7Enter
8Ice maker
9Alarm
10 Water Filter
11 12 13
11 Display
13 Fresco
12 Up/Down
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Before starting
The innovative electronic control system designed by Fhiaba maintains constant temperature on the three compartments
and visualizes it on the control panel display. It also allows user interaction making it possible to personalize settings of the
varios functions and to receive sound and/or visual messages if any malfunction should occur in the appliance.
Main control panel and Fresco control
Electronic Control
Allows complete switching on and off of the appliance
(press for three seconds).
Allows switching on and off of only the refrigerator compartment
(press for three seconds).
Allows access to the appliance function menu
It shows the temperature of the refrigerator and freezer compartments,
the date and time, Fhiaba Access functions and visual messages.
By selecting Up/Down the preset temperature can be changed accord-
ing to the selected function mode (freezer, refrigerator, Fresco).
Confirms activation or deactivation of the selections made in the Fhiaba
Access Menu.
Allows activating or deactivating the automatic ice production.
Blinks to signal possible malfunctioning, also in combination with a sound
signal which can be deactivated by pressing the button.
Shows the status of the water filter cartridge capacity.
Using the Up and Down buttons, it is possible to change the set tempera-
ture of the refrigerator and scroll through the interactive menu.
Shows the temperature of the Fresco compartment.
Allows switching on and off of only the Fresco compartment (press
for three seconds).
Using the Up and Down buttons, it is possible to change the
temperature set for the Fresco compartment.

8
4
4.1
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Appliance switching on and off
If at the first startup the Standby message does not
appear, but another message appears, it means
that the appliance has already started the cooling
process. If this is the case, deactivate any possible
sound signal by pressing the Alarm button ,
close the door and wait until the set temperature is
reached.
During the first startup, it will not be possible to use the
Fhiaba Access Menu to modify the factory settings
until the preset temperature has been reached.
Each time the appliance is switched on it goes
trough a self-diagnosis procedure lasting three min-
utes before completely starting up.
If only the refrigerator compartment or the Fresco
compartment is switched off, the specific fan will
continue to operate to prevent the formation
of unpleasant odors and mold.
Before switching off the appliance for a long period
of time, remove all of the items inside and leave the
doors and drawers open to prevent the formation of
unpleasant odors and mold.
When the appliance is connected to the electrical power supply but has
not yet been switched on, the display shows the message
(safety message to warn that the appliance is connected to the mains,
and all the panel buttons are off.
To switch on all the appliance compartments, press the Unit button for
three seconds.
First startup
When the appliance is first switched on the TriMode compartment is set to
the “freezer” mode. After switching on it remains always on and can be
switched off only by switching off the complete appliance.
Press Unit for three seconds.
During periods of long absence it is recommended to switch off the refrig-
erator by pressing the Unit button for three seconds and disconnecting
the electrical plug or the omnipolar switch controlling the socket.
Completely empty the refrigerator, clean and dry it and leave the doors
and drawers partially open to prevent unpleasant odors.
Switching off the Refrigerator and Fresco
compartments
Restarting
Switching off for long periods
Switching on and off
Use the same buttons to restart.
The freezer compartment always stays on and cannot be switched off
except by completely switching off the appliance by pressing the Unit
button for three seconds.

9
4
4.3
4.4
4.2
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
An integrated control system provides information through lighted signals
or text messages visualized on the display.
The information signal is always visualized with a fixed text message, while
a malfunction signal is visualized with blinking text. The sound signal that
accompanies some malfunction signals can be deactivated by pressing
the Alarm button on the main control panel.
The list of malfunction signals is located at the back of this manual.
Appliance switching on and off
Each model has been carefully tested before leaving the factory and is
adjusted in such a way to ensure high performance and low consump-
tion. Usually, it is not necessary to modify the settings.
Nevertheless, according to special needs, it is possible to modify the set
temperatures as follows:
Refrigeration Compartment
Fresco Compartment
Freezer Compartment
(TriMode)
From +2°C to +8°C (from 35.6°F to 46.4°F), the recommended preset tem-
perature is +5°C (41°F).
To adjust the temperature use the Up/Down buttons . Upon touching
these buttons the newly set temperature will appear in the display. To
modify this temperature, use the buttons until reaching the desired tem-
perature.
From -2°C to +2°C (from 28.4°F to 35.6°F), the recommended preset tem-
perature is 0°C (32°F).
To adjust the temperature use the Up/Down buttons . Upon touching
these buttons the newly set temperature will appear in the display. To
modify this temperature, use the buttons until reaching the desired tem-
perature.
From -15°C to -22°C (from 5°F to -7.6°F), the recommended temperature
is preset at -18° (0°F).
To adjust the temperature use the Up/Down buttons . Upon touching
these buttons the newly set temperature will appear in the display. To
modify this temperature, use the buttons until reaching the desired tem-
perature.
In case the compartment is used as refrigerator or Fresco compartment
(TriMode function) the recommended and preset temperatures will cor-
respond to those indicated for the respective compartments.
The temperature shown can vary slightly in respect
to the set temperature following frequent openings
of the doors or insertion of room temperature foods
or large quantities of foods.
6 to 12 hours are necessary to reach the selected
temperature.
Ice Maker Activation
That Ice Maker button located on the main control panel permits ac-
tivation of the automatic icemaker. The button is lighted when the ice-
maker is functioning.
A prewash of the hydraulic circuit should be performed before activating
the Ice Maker for the first time. To do this touch at the same time buttons
Enter and Ice Maker .
After a few minutes the Ice Maker can be activated.
Information and malfunction messages on the display
How to adjust the temperature for different requirements
Do not activate the Ice Maker unless the appliance
is connected to the water mains.

10
5
5.1
5.2
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Settings and Special Functions
It is possible to customized the functions of your Fhiaba to adapt it to
diverse usage needs, resetting the main parameters (Settings) or acti-
vating special functions (Functions).
Functions are visualized on the main display by pressing the Fhiaba
Access button .
The Up/Down buttons permit scrolling the available functions, which
can be selected by pressing the Enter button . The display visualizes
the current functioning status.
Using the Up/Down buttons , it is also possible to scroll through the se-
lected function, activating or deactivating by pressing the Enter but-
ton . Once the function is confirmed, the display will automatically
visualize the main menu to select other functions.
At any time it is possible to return to the previous selection through the
FhiabaAccess button .
The language of the messages appearing on the display can be
changed by operating as follows:
Enter the Menu by pressing the Fhiaba Access button select Set-
tings via the Up/Down buttons and confirm via Enter . Then select
the Language function and the desired language.
To prevent an inadvertent change to the settings
the keypad is automatically locked after a cer-
tain period of time.
To re-activate the Fhiaba Access function, press
simultaneously the Fhiaba Access button and
the Down button for at least three seconds.
Customization and language settings
Special functions activated through the Fhiaba Access Menu
The function lowers the refrigerator temperature to +2°C (35.6°F) for 12
hours, permitting more rapid cooling of food that has just been placed
in. Once the 12 hours have expired, the function deactivates auto-
matically, returning to the previously set temperature. It is possible to
program a timed activation of the function. After a prolonged inter-
ruption of electrical current, it is necessary to reactivate the function.
It is possible to program the function with a delay of 1 to 12 hours.
This function (recommended in case of prolonged absences since it al-
lows considerable energy savings) brings the refrigerator compartment
temperature to +14°C (57.2°F). It is possible to program the duration, or it
can be manually deactivated upon re-entry after a period of absence.
This function remains active even if during the period of absence there is
a prolonged interruption of electrical power.
To use special functions, select the Fhiaba Access button and use
the Up/Down button to access the menu, confirming the selection
.
Shopping Fridge
How to activate
How to deactivate
How to program timed activation
Vacation Fridge

11
5
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
It is possible to program a period from 1 to 90 days.
It is possible to program the function with a delay of 1 to 12 hours.
It is possible to program a period from 1 to 90 days.
Settings and Special Functions
This function must be activated at least 24 hours before inserting room
temperature items into the freezer, or several hours before placing into
the freezer previously frozen items which have been subject to a slight
temperature rise. This function is automatically deactivated when the
programmed time period expires. It is possible o program timed activa-
tion of the function.
After a prolonged interruption of the electrical power, it is necessary to
reactivate the function.
Shopping TriMode
This function (recommended in case of prolonged absences since it al-
lows considerable energy savings) brings the TriMode compartment tem-
perature to - 18°C (46.4°F). It is possible to program the duration, or it can
be manually deactivated upon re-entry after a period of absence.
This function remains active even if during the period of absence there is
a prolonged interruption of electrical power.
How to activate
How to activate
How to activate
How to deactivate
How to program timed activation
How to deactivate upon re-entry
How to deactivate upon re-entry
How to program the duration
How to program the duration
Vacation TriMode

12
5
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Settings and Special Functions
The IceMaker function permits selecting the size of the ice cubes, by
choosing between Large (base setting) or Medium, and activation of
the SuperIce function, which increases the quantity of produced ice.
The SuperIce function deactivates automatically after 24 hours.
This function can be activated when it is necessary to cool off beverages
quickly, by placing them inside the freezer compartment.
It is possible to select a duration of 1 to 45 minutes. A sound signal will indi-
cated when the optimal temperature has been reached. After removing
the beverages, deactivate the sound signal by pressing
the Alarm button .
The function makes it possible to comply to certain religious observances
requiring that the operation of the appliance is not affected by the open-
ing or closing of the doors (the thermostatic control, the inner lighting and
the ice maker are deactivated).
Bottle Cooler
Ice Maker
How to activate
How to activate the cube size function
How to deactivate
How to deactivate
How to program the duration
How to activate the SuperIce function
How to deactivate
This function activates a courtesy light to illuminated the refrigerator area
in the dark.
Sabbath Mode (Optional)
Night Light
How to activate
How to activate the Night Light function
How to deactivate
How to deactivate the Night Light function

13
5
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Settings and Special Functions
The View Status function permits visualizing the exact quantity of filtered
water in liters and the time left before the filter needs to be replaced.
The Reset Filter function sets to zero the quantity of water filtered and the time
left before the filter needs to be replaced. It is necessary to set the meter to
zero each time the cartridge is replaced.
After 30 days from the appearance of the message “Replace Filter Car-
tridge”, ice production will be suspended and the display will visualize the
message “No Water”. To once again activate ice production it is necessary
to set the filtered water meter to zero via the Reset Filter function. The days
and the liters available before filter replacement is necessary are indicated.
This function is to be activated when it is not necessary to filter the water,
because excellent quality water is already available from the home wa-
ter system.
If the ice production is disabled for long period, the water circuit is au-
tomatically cleaned. Nevertheless, in particular cases, it is possible to
manually intervene and perform a supplementary cleaning.
Repeat the operation until the water is clean.
Correctly position the ice tray or another suitable
container under the IceMaker to collect water, then
close the drawer. At the end of the operation, wash
the tray.
Water Filter
Reset Filter
Bypass Filter
Manual Clean, Water Filter
How to check the status of the filter
How to set the filtered water meter to zero
How to activate filter Bypass
How to manually clean the filter
The View Status function permits visualizing the exact quantity of filtered
air in liters and the time left before the filter needs to be replaced.
The Reset Filter function sets to zero the quantity of air filtered and the
time left before the filter needs to be replaced. It is necessary to set the
meter to zero each time the cartridge is replaced.
Air Filter
How to check the status of the filter
How to set the filtered air meter to zero

14
5
5.3
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Settings and Special Functions
The display visualizes the hours and minutes in the format hh:mm and with
hh: blinking. Use the Up/Down buttons to modify the setting and then
confirm by pressing Enter to go on to the next setting.
Once the minutes are confirmed, the time will be set.
This function selects the display at 12 or 24 h.
Time
Set Time
How to set the time
Set 12/24
How to set the display to 12 h
How to set the display to 24 h
This offers the possibility to reset default factory settings and cancels any
previous changes.
Default Setting
How to reset default settings
Using this function it is possible to deactivate/activate the date visualiza-
tion on the display.
Show Date
How to activate the date
How to deactivate the date
The display will visualize the date in the format dd:mm:yy (day:month:year),
the day will blink. Use the Up/Down buttons to modify the setting, con-
firm with Enter to go on to the next setting; once the year is confirmed
the date will be set.
Date
Set Date
How to set the date
Select the Fhiaba Access button and used the Up/Down button
to select .
The freezer compartment can, if required, be converted to the refrigera-
tion o Fresco operating mode.
TriMode Options
How to set the Fridge function
How to set the Fresco function
How to revert to the Freezer function
Basic settings of the Fhiaba Access Menu

15
5-6
6.1
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
This function permits visualizing the temperature in Centigrade or Fahren-
heit degrees. Normally, the appliance is set for visualization in centigrade
degrees.
Set °C/°F
How to set the temperature in Centigrade
How to set the temperature in Fahrenheit
Internal Layout
Internal Layout (positioning, adjustment, removal)
Fixed to the slide guides with two locking nuts
to remove the drawer, unscrew the locking nuts and remove
the drawer
Fresco Drawer
Through this function it is possible to activate/deactivate the constant
visualization of the time.
The function allows selection of the language for the display messages.
Show Time
How to activate the permanent time
How to deactivate
Language
Italian
English
French
German
Spanish
The upper TriMode can be removed using the same method used for
the Fresco drawer
to remove the lower drawer unscrew the four locking nuts.
TriMode Drawer

1
2
16
6
1
2
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Internal Layout
The door shelves can be easily removed for cleaning
Hold the door shelf at the sides and push it upwards to release it from
its seat, then pull it outwards.
Reverse the procedure to reinstall
Door Shelves
The shelves are sliding and easily positioned by the user as follows:
pull and slightly turn the locking knob
lift the front part of the shelf and tilt it
lift or lower the shelf to the desired position
reposition the locking knob
to remove a shelf it is necessary to first remove the end parts of the
guides (unscrew the locking nut), slide it downwards and remove it.
Shelves
Located in the upper drawer of the freezer compartment
after removal, make sure to reposition it correctly.
Ice Tray
Do not place hands or fingers near the Icemaker
when in function.

17
7
7.1
7.2
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Activation and use of the Ice Maker
Activation and use of the Ice Maker
Water Filter
To activate the Ice Maker after installation of the appliance, press the
Icemaker button .
Please note that from 12 to 24 hours are necessary before ice can be
harvested. The production is of 10 cubes per cycle in approximately
10 cycles in 24 hours.
The yield depends on the temperature set in the freezer, the room
temperature and the frequency of door opening.
If the appliance is operating without being connected to the water
system, make sure that the Icemaker is deactivated by pressing the
button .
The Ice Maker produces ice until the ice tray is full and will automati-
cally stop once the maximum level is reached.
With the SuperIce function, it is possible to increase the quantity of ice
produced a 24 hours, while the Set Cube Size function permits selec-
tion of the size of the produced ice cubes.
The Water Filter makes available high-quality water for the production
of ice cubes. It provides up to 3000 liters of water for a maximum time
of six months.
On the upper right of the command panel it is possible to monitor the
use status of the filter: when the entire area is lighted the filter has just
been replaced; the white lighted area indicates that the filter capaci-
ty is below 20%. When the filter is nearly expired the message “Replace
Filter Cartridge” will appear on the display.
The filter is located inside the refrigerator compartment, near the door
hinge, protected by a flap door. Prior to change the filter switch off the
Ice Maker by pressing the IceMaker button. Then enter the Fhiaba Ac-
cess Menu and set “Manual Clean” function. At the end of the cleaning
cycle remove the water from the ice tray and wipe it dry.
Press the front of the flap door to open it and carefully rotate the filter
cartridge for a quarter rotation in a counter clockwise direction until it de-
taches from its housing. It is normal for a small quantity of water to come
out. Remove the cap of the new cartridge and insert it into the housing
by gently rotating it for a quarter rotation in a clockwise direction until it
locks into place.
Filter Replacement
It is normal that some ice cubes stick to one an-
other. If the ice is not frequently used, the older
cubes can become opaque, and will have a
strange flavor and become smaller.
The Icemaker automatically deactivates if the
Vacation function is activated.
When the Icemaker is started for the first time, it
is recommended to empty the full ice tray of the
first ice cubes.
If the equipment has been switched off for a
month or more, it is recommended to performe a
water filter cleaning cycle.

18
8
8.1
www.fhiaba.com ∙ [email protected] ∙ Info Line 800-344222 ∙ Tel [phone] ∙ Fax [phone]
Lighting
Lighting
To provide optimum interior lighting, LED strips illuminate the refrigera-
tor compartment from the top and sets of LED lights directly illuminate
different areas of the refrigerator compartment, of the Fresco drawers
and the freezer drawer.
In case of malfunction and/or breaking down of the lighting system,
the repair should be carried out only by a qualified Fhiaba Service
technician.