Fillauer Hosmer 8 User manual

Hosmer
8, 8X, 88X
Hooks
Product Manual

2
Contents
Intended Use................................................................3
Warnings and Precautions ....................................................3
Qualied Provider ...........................................................4
Specications and Preparations BeforeUse
(Risk Management for Installation andCalibration) ...............................4
Compatibility ................................................................5
Disposal/ Waste Handling ....................................................5
Warranty ...................................................................5
User Instructions ............................................................6
Serious Incidents ............................................................6
To see other language options, visit llauer.com.

3
Intended Use
The Model 8, 8X, and 88X are prosthetic terminal devices that are commonly referred
to as “canted split hooks” and are used to provide for both ne prehension and
gross grasping of objects when controlled through a cable that is operated with
body motions. These hooks are a voluntary-opening device and grasping tension is
adjusted by the adding of tension bands, rings, or springs (see catalog for additional
information). There are also smaller sizes available; see llauer.com for information
on other sizes of canted hooks.
Performance Characteristics
Model 8 Model 8X Model 88X
Size Medium Adult Medium Adult Medium Adult
Length 4.625 in.
(11.7cm)
4.625 in.
(11.7cm)
4.625 in.
(11.7cm)
Weight 8 oz. (227g) 7.5 oz. (213g) 4 oz. (113g)
Material Stainless Steel Stainless Steel Aluminum
Grip Serrated Surface Nitrile Lined Nitrile Lined
These devices are intended for single patient use only.
Storage and Handling
It is recommended that prosthetic hooks (or prosthetic/orthotic components) be
stored in a cool, clean, dry environment away from harsh chemicals (chlorine, acids,
acetone, etc.).
Warnings and Precautions
CAUTION: Nitrile coatings are not intended for use in high temperature
applications. Refrain from contact with items that are above 85°C (185°F)
as damage to the coating may occur.
NOTICE: An upper-limb prosthetic device user’s ability to drive should be
determined on a case-by-c ase basis by a specialist. Contact your local
governing authorities regarding any driving restrictions or limitations.
WARNING: Body-powered devices should not rely on cable tension for
grasp control if the user has been cleared to drive with the prosthesis.

4
Failure to maintain tension while controlling the steering wheel could
cause serious injury or death.
CAUTION: Abnormal or improper environmental conditions will lead
to malfunctioning and damage of the prosthesis and are not covered
under the warranty of the device. This prosthetic component must not
be subjected to dust/debris, liquids other than fresh water, abrasives,
vibration, activities which would damage the biological limb, or prolonged
extreme temperatures (<-5°C or >50°C). Do not allow debris or liquids to
remain in the prosthesis and its components during use. Rinse the device
with fresh water and dry immediately after exposure.
CAUTION: The hook is waterproof to 1 meter. However, if the hook is
submerged, it should be rinsed with fresh water and dried immediately to
remove salt, chlorine, or debris.
Qualied Provider
Attachment, adjustment, alignment, and delivery of this device must be performed by
or under the direct supervision of a qualied prosthetist. Unless stated in this manual,
any such activities should not be attempted by the user and will potentially void the
device warranty.
Specications and Preparations BeforeUse
(Risk Management for Installation
andCalibration)
Installation
The hook may be installed in any Fillauer wrist unit with a ½-20 thread. Follow the
instructions provided with the wrist unit for best results.
Cabling
The hook “thumb” has been designed with a receiver for a ⁹⁄³² inch ball terminal. A
triple swivel with ⁹⁄³² inch ball terminal should be selected with a cable connection that
matches the cable used in the prosthesis. Cable routing should ensure a direct line of

5
pull that minimizes bends in the cable, otherwise excess cable friction or failure could
result.
Adding Tension to Hook Grasp
To add more force to the grasp of the hook, additional tension bands may be applied
using the E-Z Hook Tension Band Applier (55144) or similar device. Additional bands
are included with the hook and are available in beige (53869) or black (53869-BLK).
For greater tension, hook rings (57500) or stainless-steel tension springs (55363) may
be used. Tension springs are recommended for situations where chemical or heat
exposure could cause band or ring failure.
Compatibility
Fillauer hooks have been tested with and are recommended for use with Fillauer wrists
that have a ½-20 internal thread. They may be used with any equivalent ½-20 threaded
wrist units; however, damage caused by other manufacturers wrist units is not covered
under warranty of this device.
Only Fillauer tension bands, hook rings, and tension springs may be used with Fillauer
hooks to adjust the grasping force of the hook.
Disposal/ Waste Handling
The product must be disposed of in accordance with applicable local laws and
regulations. If the product has been exposed to bacteria or other infectious agents,
it must be disposed of in accordance with applicable laws and regulations for the
handling of contaminated material.
All metal components may be removed and recycled at the appropriate recycling
facility.
Warranty
This product has an 18-month warranty against manufacturer defects.

6
User Instructions
The providing health care professional must review the following information directly
with the user.
Care and Maintenance
CAUTION: Nitrile coatings are not intended for use in high-temperature
applications. Refrain from contact with items that are above 85°C (185°F)
as damage to the coating may occur.
NOTICE: Nitrile coatings are expected to wear under normal use. The
coating can be replaced but is not covered under warranty, except for
manufacturer defect.
NOTICE: An upper-limb prosthetic device user’s ability to drive should
be determined on a case-by-case basis by a specialist. Contact your local
governing authorities regarding any driving restrictions or limitations.
WARNING: Body-powered devices should not rely on cable tension for
grasp control if the user has been cleared to drive with the prosthesis.
Failure to maintain tension while controlling the steering wheel could
cause serious injury or death.
CAUTION: Abnormal or improper environmental conditions will lead
to malfunctioning and damage of the prosthesis and are not covered
under the warranty of the device. This prosthetic component must not
be subjected to dust/debris, liquids other than fresh water, abrasives,
vibration, activities which would damage the biological limb, or prolonged
extreme temperatures (<-5°C or >50°C). Do not allow debris or liquids to
remain in the prosthesis and its components during use. Rinse the device
with fresh water and dry immediately after exposure.
CAUTION: The hook is waterproof to 1 meter. However, if the hook is
submerged, it should be rinsed with fresh water and dried immediately to
remove salt, chlorine, or debris.

Serious Incidents
In the unlikely event of a serious incident, seek immediate medical help and contact
your prosthetist at your earliest possible convenience. Clinicians should contact their
local Fillauer representative immediately in the event of any device failure.

www.llauer.com
Fillauer LLC
2710 Amnicola Highway
Chattanooga, TN 37406
423.624.0946
Fillauer Europe
Kung Hans väg 2
192 68 Sollentuna, Sweden
[phone]
EC REP
© 2021 Fillauer LLC
M085/10-06-21/Rev.1