Fillauer Myo/One User manual

Product Manual

3
Contents
Intended Use................................................................4
Warnings and Precautions ....................................................5
Risk Management............................................................5
Installation..................................................................6
Troubleshooting .............................................................8
MAUI App for iOS ............................................................9
Compatibility ................................................................9
Safety Caution..............................................................10
Disposal/ Waste Handling ...................................................10
Serious Incidents ...........................................................10
Warranty ..................................................................10
Return Policy ...............................................................11
Customer Support ..........................................................11
Declaration of Conformity....................................................11
Customer Support ..........................................................12

4
Intended Use
Welcome to the Myo/One Electrode System. Designed in conjunction with Coapt™, one
small preamplier provides 2 channels of EMG signal. Controlseal™ by Coapt remote
electrode domes require no dummies, are quick to install, and can be easily moved for
optimal electrode placement. Snap Electrodes for roll on liners are also available. With
Bluetooth connectivity, the gain adjustments for the electrodes are conveniently made
via the Motion Arm User Interface (MAUI).
Myo/One is a convenient, small, versatile, package that provides a much simpler
system for dual-channel direct EMG control.
Indications
• The Myo/One electrode is intended for non-invasive monitoring of
Electromyography (EMG) for use in the control of electrically powered prosthetic
devices.
Contraindications
• Contraindicated for patients where myoelectric control is not appropriate.
The device is intended for single patient use only.
Performance Characteristics
Myo/One
Operating Temperature -5 – 60°C (23 – 140°F)
Transport & Storage Temperature -18 – 71°C (0 – 160°F)
Operating Voltage Range 5 – 20 Vdc
Storage and Handling
It is recommended that Myo/One is stored between -18 – 71°C (0 – 160°F) in a clean,
dry environment away from harsh chemicals (chlorine, acids, acetone, etc.).
Replacement Parts
Description Size Quantity Product Number
Controlseal™ Domes with
Hardware & Tool Standard 6 ea 1705002
Controlseal™ Domes with
Hardware & Tool Large 6 ea 1705003
Operating Voltage Range
Controlseal™ Dome Large 1 ea 1705001

5
Warnings and Precautions
NOTICE: Avoid locating electrodes over bony prominences. This could
cause discomfort and skin irritation.
NOTICE: Ensure the ControlSeal™ electrode cap assembly remains intact.
A missing or broken cap could cause the electrode to short out and not
function correctly, especially with the use of carbon ber forearms.
NOTICE: Use care in routing the wires, especially upon installation or
removal of the inner socket into the outer socket. If wires are cut or
damaged the system will not function. Damaged wires are not covered
under warranty.
NOTICE: The electrodes must all remain in contact with the skin. Any loss
of electrode contact will cause unwanted motion of the myoelectric device.
NOTICE: For remote electrode use, the socket wall should be between 1.9
and 5.5 mm thick. For socket walls thicker than 5.5mm, contact Fillauer
Motion Control.
NOTICE: When installing remote electrodes, don’t use silicon sealant or
Loctite to secure electrodes to screws as they could interfere with the
signal. They are unnecessary.
NOTICE: While no dummies are necessary for inner socket fabrication,
ensure there is sucient space between the inner socket and the outer
socket to accommodate the electrode cap assembly ⅛inch (3.2mm) or
snap cap assembly ¼inch (6.3mm).
Risk Management
To minimize the risk of device damage or injury to the user while maximizing the
functions of this device, follow the instructions for installation, and use this device as
described in this manual.

6
Installation
Controlseal™ ElectrodeDomes
The ControlSeal™ electrodes provide simple
quick and versatile installation into the socket.
Please refer to Coapt Electrode Dome Handbook
in the link provided on page 11 for more
information. The electrode wires are color coded
red and blue. These colors correspond to the
wires coming out of the preamp and the settings
in the user interface.
NOTICE: Disregard the instruction
on page 13 of the ControlSeal™
manual if it is being used for
reference. This applies only when
using Coapt control. See more
information at the link provided for
the Coapt Manual.
If possible, install the sensing electrodes between 1 and 2 inches (25 – 50mm) apart.
This may not be possible with extremely short transradial ttings. In those cases,
make sure the electrodes are not touching. The ground electrode (black lead) can go
anywhere in the socket with good electrode contact, at least one inch from sensing
electrodes if possible.
Snap Electrodes for Roll-on Liners
Locate the electrode site, using a small awl,
make a small hole in the roll-on liner. Insert
the electrode and tighten the snap onto the
stud. A pair of snap ring pliers can be used to
snug it up. Once the position of the electrodes
is nalized, a small drop of cyanoacrylate
(super glue) to the backside of the snap (in the
small holes) will lock the electrode in place.
Do not allow glue to get on the threads of
thesnap.
Instruct your patient to use care when un-
snapping the electrode cap from the electrode
to prevent tearing the liner. The snap caps
are color coded red and blue. These colors

7
correspond to the wires coming out of the preamp and the settings in the user
interface.
Forearm Fabrication for Controlseal™ & Snap Electrodes
Standard myoelectric forearm fabrication techniques should be used. The forearm
must be hollow and the inner socket removable to allow access to the internal
electronic components. If there is a pull tube for donning the prosthesis, ensure it is
well sealed so perspiration does not enter the forearm. The connections with the wrist
components and battery connections are likely not waterproof and prone to damage
by perspiration.
Ensure there is ⅛ inch (3.2mm) space between the inner and outer sockets for the
protective plastic caps on the ControlSeal™ electrodes and ¼ inch (6.4mm) on the
electrode snaps for roll-on liners. Also ensure there is a space for the wires and the
Myo/One preamp. A dummy has been provided for the preamp.
The Myo/One Electrode wires are held in place by
a moveable slide. In most cases there is adequate
separation for the wires to reach the electrodes. If
the electrode sites are farther apart, simply move
the slide down the wire set and gently separate
the wires. Conversely, if the wires get separated
too much, gently move the slide back toward the
connectors.
Adjustment
Myo/One electrodes have the same gain adjustability as traditional electrodes. Rather
than using a screwdriver on a small mechanical gain pot accessed at the back of the
electrode, gain adjustment is made via Bluetooth on your Apple handheld device.

8
1. Download MAUI on your Apple device (see page 9)
2. Power cycle the system to “wake up” the Bluetooth transmitter in the electrode.
3. When you open the app and search for devices, any ProPlus device will appear
along with the Myo/One electrodes. Tap on the ‘Myo/One’ to connect.
In the user interface, the gain (signal amplication) can be adjusted. The higher the
gain setting, the greater the amplication for weak signals. The lower the setting
proportional control improves. Filtering can also be adjusted. Increased ltering results
in smoother control.
These adjustments are necessary when using devices without a user interface. On
devices with a user interface, adjustments in the electrode are “ballpark” adjustment.
Adjust the electrodes to get close, then make ne adjustments in the device’s user
interface. This is especially true if the wearer is using more than one myoelectric
device; e.g., interchanging between a Taska hand and an ETD.
Troubleshooting
Myo/One not found in MAUI
1. Ensure the battery power switch is in the On position.
2. Power cycle the system to “wake up” Bluetooth.
3. Check battery charge.
4. Check all connections and wires.
Erratic, Max, or no signal from electrode
1. Check for electrode contact.
a. Even if there is slight contact it could be intermittent.
b. Check signal and contact as the wearer moves through range of motion
2. Check connections, especially the Electrode Cap Assemblies.
3. Check to make sure the screw connections on both remote electrodes or snap
electrodes is tight, and threads are free of threadlocker, sealant, or glue.
4. Check other components that may be “upstream” of the device; e.g., electric
wrist rotator, powered elbow etc.
Very weak signals
1. Check the Myo/One gain adjustment in the User Interface, increase the gain if
necessary.
2. Check electrode contact.
3. Check electrode placement.
4. Check connections.

9
MAUI App for iOS
Quick Setup for Motion Arm User Interface for Apple® iOS (MAUI)
1. From the Apple® App Store download the MAUI app .
2. Enter the Prosthetist Code: PR-MCAK. Patients do not require a code.
3. Open the App and follow the Tutorial.
4. Go to the Connect screen and tap Scan .
5. Input the Pairing Key that came with the device. This key should be kept in the
patient’s record.
6. The device is now connected to the MAUI.
7. To disconnect, tap the Connect icon in the lower left corner, then tap
Disconnect .
Troubleshooting
• Make sure the battery on the device is fully charged
• Conrm the device is turned on
• Verify that you are not in Simulation Mode by double tapping the Home key, then
swiping MAUI o the screen, and reopening the app
• Bluetooth® must be turned on in Settings on the iOS device.
• The Information icon provides information about a function
• To repeat the tutorial, go to and tap on Reset Guided Tutorial.
System Requirements
• iOS 11 minimum
• iPad® (5th gen and later)
• iPad mini® (2nd gen and later)
• iPad Air®
• iPad Pro®
• iPod Touch® (6th gen and later)
• iPhone® 5s and later.
Compatibility
The Myo/One electrode is intended for use in the control of electrically powered
prosthetic devices sold for use with single, double, and multisite myoelectric control.
Myo/One is incompatible with Espire Elbow Pro and Espire Elbow Hybrid.

10
Safety Caution
Use caution when using this device in situations where injury to yourself or others may
occur. These include but are not limited to activities such as driving, operating heavy
machinery, or any activity where injury may occur. Conditions such as a low or dead
battery, loss of electrode contact, or mechanical/electrical malfunction (and others)
may cause the device to behave dierently than expected.
Disposal/ Waste Handling
This device, including any associated electronics and batteries should be disposed
of in accordance with applicable local laws and regulations. This includes laws and
regulations regarding bacterial or infectious agents, if necessary.
All metal components may be removed and recycled at the appropriate
recyclingfacility.
Serious Incidents
In the unlikely event a serious incident occurs in relation to the use of the device, users
should seek immediate medical help and contact their prosthetist, local competent
authority and Fillauer at the earliest possible convenience. Clinicians should at
any time contact their local Fillauer representative and local competent authority
immediately in the event of any device failure.
Warranty
Seller warrants to Buyer that the equipment delivered hereunder will be free from
defects in materials and manufacturing workmanship, that it will be of the kind and
quality described and that it will perform as specied in Seller’s written quotation.
The limited warranties shall apply only to failures to meet said warranties that appear
within the eective period of this Agreement. The eective period shall be one year
(12 months) from the date of delivery to the tting center that has purchased the
components. Refer to the shipping receipt for the date of shipment.

11
Return Policy
Returns are accepted from date of shipment as follows with the addition of any
repairs that may be required to return the product to resalable condition:
Return Policy
Up to 30 days No restocking fee
31 – 60 days 10% restocking fee
61 – 90 days 15% restocking fee
90+ days Not accepted
Customer Support
Americas, Oceania, Japan
Motion Control Inc.
A Fillauer Company
115 N. Wright Brothers Drive
Salt Lake City, UT 84116
801.326.3434
motioninfo@llauer.com
Europe, Africa, Asia
Fillauer Europe
A Fillauer Company
Kung Hans väg 2
192 68 Sollentuna, Sweden
[phone]
support@llauer.com
Declaration of Conformity
The product herewith complies with Medical Device Regulation 2017/745 and is
registered with the United States Food and Drug Administration. (Registration
No.1723997).
For more detailed information on the
Coapt ControlSeal™ Dome Electrodes,
please use this link.
https://llauer.com/
myoone-electrodes/

Fillauer
2710 Amnicola Highway
Chattanooga, TN 37406
423.624.0946
Fillauer Europe
A Fillauer Company
Kung Hans väg 2
192 68 Sollentuna, Sweden
[phone]
EC REP
© 2023 Fillauer LLC
1910133/06-05-23/Rev.1