Finelite HP-2 User manual

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
1
HP-2 Indirect/Direct Mitered Corner Installation Instructions
© 2016 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98281 V2. 11/16
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Secure To Structure
(by others)
Power Cords
Canopy GridBox™
Starter
Top Glow™ Diffuser
Bottom Diffuser
Starter
Step 1
Remove diffusers from starter and set aside to prevent it from getting
dirty or damaged.
Aircraft Cable
Power Cords
Caddy Clip
Starter
GridBox™
Canopy
Secure To Structure
(by others)
Step 2
Install GridBox™ and caddy clip onto ceiling grid, then canopies and aircraft cable assemblies. Align aircraft cables to grippers
and insert on both ends of the luminaire. Adjust pendant to proper height and level. Press down on top of gripper to release
locking mechanism if needed. Secure luminaire to structure using tie-wire (by others) according to code.
Step 3
Install power cable through canopy and into GridBox. Make electrical connections in GridBox.
Power Cords
Gripper
Feed Hole
Starter
Safety Stop
Step 4
Slide safety stop and safety crimp up to the aircraft cable
within 9" of cable gripper. Trim excess cable and insert safety
bar assembly through feed hole.
Bottom Diffuser
Joiner/Ender
Top Glow™ Diffuser
Step 5
Remove diffusers from joiner/ender and set aside to prevent it from getting dirty or damaged.
Aircraft Cable
Cable Bushing
Ceiling
Luminaire
Locate aircraft cables.
Power Cords
Aircraft Cable
Press Here To Release
Gripper
Canopy
Power Cords
0 - 10V
Dimming
Scan QR co e for
helpful vi eo(s)

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
2
HP-2 Indirect/Direct Mitered Corner Installation Instructions
© 2016 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98281 V2. 11/16
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Caddy Clip
Starter
Canopy
Step 6
Install caddy clip for joiner/ender.
Yoke Brackets x2
(provided)
Joint Sleeve
#10-32 x 5/8"
Screws x2 (provided)
Joiner/Ender
Starter
Step 11
IMPORTANT STEP: Secure joint with two yoke brackets (provided) using
#10-32 x 5/8" screws (provided). CAUTION: When installed correctly these
brackets will pull luminaires together to make a tight joint. Do not over-tighten.
Power Cords
Gripper
Feed Hole
Joiner
Safety Stop
Step 7
Slide safety stop and safety crimp up to the aircraft
cable within 9" of cable gripper. Trim excess cable
and insert safety bar assembly through feed hole.
Starter
Inner Joiner Sleeve
Aircraft Cable
Joiner/Ender
Joiner Sleeve
Step 8
Align starter and joiner/ender, then slide luminaires together.
Remove back plate clips (provided) to release back plates. We recommend using
a flat head screwdriver to get them loose. CAUTION: Do not lose these pieces.
Joiner/Ender
Starter
Double Diffuser
(pre-installed)
Step 9
Back Plate Clip
Back Plate
Joiner/Ender
Starter
Step 10
Pivot Point
Slowly swing down back plates. CAUTION: Do not twist back plate when swinging own – it
will come out of the support extrusion. ote that the screw shown is the pivot point and the
back plate can be slid a few inches either way for ease of access to the driver space.
IMPORTANT STEP

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
3
HP-2 Indirect/Direct Mitered Corner Installation Instructions
© 2016 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98281 V2. 11/16
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Bottom Diffuser
Top Glow™ Diffuser
Joiner/Ender
Starter
Plug-Together Wiring
Joiner/Ender
Starter
Step 12 Step 14
Connect plug-together wiring. Reinstall diffusers and turn power on to luminaire.
Replace back plates by holding them in their original position and pushing
the clips back in. Make sure wire connections are not pinched. (If 1 ft.
back plate assembly is near joint, reconnect feed harness to LED board).
Joiner/Ender
Starter
Double Diffuser
(pre-installed)
Back Plate Clip
Step 13