Finelite HP-4 Recessed User manual

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
1
rotected by one or more US atents: 8915613; D702,391; D702,390; D700,732
HP-4 Wall Mount Indirect Starter/Independent
Installation Instructions
© 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98196 V2. 04/17
6" 6"
Feed
End Starter/Independent
Wall Rail
Point A
.
.
2"
2-5/16"
4-1/2"
1-1/4"
Junction Box
(Feed Location)
Electrical
Connections
Diffuser
Starter
Step 1
Remove Top Glow™ diffuser and set aside to
prevent it from getting dirty or damaged.
Feed Location
Junction Box
Wall Mount Rail
.
4-1/2"
1-1/16"
6"
1-1/2"
Step 3A
A) Use feed location to center and install junction box. osition and install
starter wall rail.
Top Hook
Bottom Hook
Wall Rail
Luminaire
Wall
Step 6
Install luminaire onto wall rails then slide it straight down to
engage hooks on top and bottom of wall rail.
Step 5
Make electrical connections and push completed
wiring into junction box.
Step 2
osition luminaire on wall in desired location. Mark the bottom corner of the luminaire, do
not include end cap. This will be oint A. Use oint A to find and mark feed location.
Wiring
#10 Screws (by others)
Step 4
Level wall rail to ensure proper mounting. Install
#10 screws (by others) through rail and into
backing.
.
Point A
End Cap
Step 3B
0 - 10V
Dimming
Scan QR code for
helpf l video(s)
B) Center of mounting rail for independent is 6" from oint A as indicated. Make sure rail has
proper backing (by others).

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
2
rotected by one or more US atents: 8915613; D702,391; D702,390; D700,732
HP-4 Wall Mount Indirect Starter/Independent
Installation Instructions
© 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98196 V2. 04/17
Step 7
Install #8-18 x 1/4" adjustment screws (provided) onto
mounting brackets. Use screws to level luminaire. Tighten
to raise and loosen to lower.
Diffuser
Step 8
Reinstall Top Glow diffuser and power on luminaire. NOTE: If
part of a longer run, diffuser will be reinstalled back into
original luminaire section as lengths vary.
#8-18 x 1/4"
Adjustment screw
(provided)

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
1
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732
HP-4 Wall Mo nt Indirect
Joiner/Ender Installation Instructions
© 2017 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98197 V2. 04/17
Diffuser
Joiner / Ender
Step 1
Remove joiner Top Glow™ diffuser and set aside to
prevent it from getting dirty or damaged. NOTE: If part
of a longer run, diffuser will be reinstalled back into
original luminaire se ction as lengths vary.
Starter
Joiner/Ender
#8-18 x 1/2" Combo
Hex Screws (provided)
Step 6
Remove trap door #8-18 x 1/4" screws (provided) to open
trap door. Install #8-18 x 1/2" combo hex screws
(provided) into end brackets. CAUTION: Do not
over-tighten.
6"6"
Luminaire Length
Minus 6"
Luminaire Length
Minus 6"
Luminaire Length
Starter Joiner Ender
Wall Rail
Point A Wall Rail
Center of the Rail
Step 2
Position wall rails as indicated above. Center of mounting rail for starter is 6" from Point A as indicated on the Starter/Independent installation instructions (step 3A and 3B).
Make sure wall rail has proper backing (by others).
#10 Screws
(by others)
Level wall rail to ensure proper mounting. Install
#10 screws (by others) through rail and into
backing.
Step 3
Aligner Sleeve
Plug Together Wiring
Starter
Joiner/Ender
Step 4
Connect plug-together wiring. Slide starter and joiner/ender luminaires together.
0 - 10V
Dimming
Scan QR code for
helpf l video(s)
Wall Bracket (Top Hook)
Wall Bracket (Bottom Hook)
Wall Rail
Luminaire
Wall
Step 5
Position the luminaire in place and slide the wall bracket
straight down to engage top top and bottom hooks of the
wall bracket into the wall rail. Be careful not to damage
any wiring.

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
2
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732
HP-4 Wall Mo nt Indirect
Joiner/Ender Installation Instructions
© 2017 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98197 V2. 04/17
Light Leak
Cover
Starter
Joiner
Install light leak covers on all joints.
Step 8
Starter
Joiner/Ender
Diffuser
Reinstall Top Glow™ diffuser and turn on luminaire. NOTE: If part of a longer run,
diffuser will be reinstalled back into original luminaire section as lengths vary.
Starter
Joiner/Ender
Step 10
Install #8-18 x 1/4" adjustment screws (provided) onto mounting brackets. Use
screws to level luminaire. Tighten to raise and loosen to lower.
Step 9
#8-18 x 1/4"
Adjustment screw
(provided)
#8-18 x 1/4"
Screws (provided)
Starter
Joiner/Ender
Aligner
Sleeve
Step 7
Install two #8-18 x 1/4" screws (provided) onto aligner sleeve. Replace trap door
and fasten trap door screws.