Finelite HP-6 Recessed Flush Diffuser Tech Zone 6"... User manual

HP-6 Recessed 1" T-Bar Mitered Corner Installation Instructions
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
© 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98370 V2. 04/17
Note: All power connections to be installed to local/national codes
by a Certified Electrician. 1
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Install starter luminaire on to T-Bar. Install T-Bar bracket onto luminaire. Secure with #8-18 x 1/4" screws (provided). Secure
luminaire to structure using tie-wire (by others), as per code.
Starter
Secure to Structure
(by others)
T-Bar Bracket
#8-18 x 1/4" Screws (provided)
Starter
Remove diffusers and set aside to prevent it from getting dirty
or damaged. NOTE: If part of a longer run, diffuser will be
reinstalled back into original luminaire section as lengths vary.
0 - 10V
Dimming
Scan QR code for
helpful video(s)
Starter
Diffuser
Step 1 Step 2 Step 3
Run power cables through conduit plate and jam nut. Make electrical
connections. Secure conduit onto conduit plate with jam nut, and
reinstall conduit plate carefully not to damage any wiring.
Remove conduit plate from luminaire. NOTE: Purple
and gray wires are for Low Voltage Control.
Attach optional splice box to conduit plate by hooking onto
splice box bracket. Insert wires through feed hole.
Run power cable through knock-out. Make electrical connection.
Secure conduit on to splice box with jam nut and close conduit plate.
Conduit Plate
Wires
Conduit
Conduit Plate
Jam Nut
Wires
Splice Box
Splice Box
Bracket
Jam Nut
Conduit Plate
Step 4 Step 5
OPTIONAL SPLICE BOX OPTIONAL SPLICE BOX
Screws
Conduit Plate

HP-6 Recessed 1" T-Bar Mitered Corner Installation Instructions
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
© 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98370 V2. 04/17
Note: All power connections to be installed to local/national codes
by a Certified Electrician. 2
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Remove backplate clips to release the backplates at corner joint. We recommend using a flat
head screwdriver to get them loose. CAUTION: Do not lose these pieces.
Slowly swing down backplates. CAUTION: Do not twist the backplate when swinging down – it
will come out of the support extrusion. Note that the screws shown are the pivot point, and
the backplate can be slid a few inches either way for ease of access to the driver space.
IMPORTANT STEP: Secure joint with two yoke brackets (provided) using 2 #10-32 5/8” screws
(provided). When installed correctly these brackets will pull luminaires together to make a tight
joint. CAUTION: Do not over-tighten.
Pivot Point
Joiner/Ender
Starter IMPORTANT STEP
Yoke Bracket
(provided)
Joint Sleeves
#10-32 x 5/8" Screws (2) (provided)
Backplate Clips
Slide joiner/ender luminaire onto T-Bar. Align elbow sleeves with channels in luminaire body. Slide joiner/ender onto starter.
Starter
Joiner/Ender
Joiner/Ender
Starter
Remove diffusers from joiner/ender and set aside to prevent it from getting dirty or damaged.
NOTE: If part of a longer run, diffuser will be reinstalled back into original luminaire section as
lengths vary.
Joiner/Ender
Diffuser
Elbow Sleeves
Step 6 Step 7 Step 8
Step 9 Step 10 Step 11

HP-6 Recessed 1" T-Bar Mitered Corner Installation Instructions
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
© 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98370 V2. 04/17
Note: All power connections to be installed to local/national codes
by a Certified Electrician. 3
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Connect plug-together wiring. Replace backplate clips by holding them in their original position
and pushing the clips back in. Make sure wire connections are not pinched. (If 1 ft. backplate
assembly is near joint, reconnect feed harness to LED board).
Secure starter and joiner/ender to T-Bar with #6-20 x 1/2" self drilling sheet metal screws
(provided). Secure luminaire to structure using tie-wire (by others), as per code.
Replace diffusers and turn power on to luminaire. NOTE: If part of a longer run, diffuser will be
reinstalled back into original luminaire section as lengths vary.
Plug-Together Wiring
T-Bar
Bracket
Diffusers
#6-20 x 1/2" Self Drilling
Screws (provided)
#6-20 x 1/2" Self
Drilling Screws
(provided)
Joiner/Ender
Starter
Secure to Structure
(by others)
Backplate Clips
Step 12 Step 13 Step 14