Finn 5 Series Service manual

TECHNICAL BULLETIN
No. 2015-0008
Date Released: December 2, 2015
PRODUCT: T1 7 0 , MB5 0 ( 5 - Se r ies)
TOPI C: I nit ia l se t up of r epla cem ent Cum m ins T4 F En gin e D isp lays
EFFECTI VI TY: ALL M L SERI AL NUM BERS
Purpose:
On all Finn machines equipped with a Cummins QSF2.8 engine (075880), some engine settings are set at
the factory and are password protected to prevent tampering. When a new replacement control box
assembly or display is installed on one of these machines, those settings need to be re-input for proper
operation of the engine and machine. This Technical Bulletin provides the steps for this process. The
steps for the T170 and MB50 machines differ slightly from one another and are detailed separately
below.
DO NOT DEVIATE FROM THE SETTINGS PROVIDE BELOW. OPERATING THE MACHINE WITH
SETTINGS OTHER THAN THOSE APPROVED HEREIN BY FINN CORPORATION COULD RESULT IN
DAMAGE TO THE EQUIPMENT, DEATH, OR SERIOUS INJURY.
Affected Part Numbers are as follows:
008795 CONTROLLER/DISPLAY CUMMINS T4F
008799 T170 CONTROL BOX ASSEMBLY
Steps (T170):
1. After display or control box is installed, Turn the key switch to “ON”. It is not necessary to start
the engine.
2. On the display, press any key to activate the Soft Key menu.
9281 LeSaint Drive Fairfield, Ohio 45014-5457 U.S.A.
[phone] 800-543-7166 Fax [phone] www.finncorp.com
Page 1of 6

TECHNICAL BULLETIN
No. 2015-0008
Date Released: December 2, 2015
3. Press the middle Soft Key with the wrench icon above it to access the Main Menu.
4. Scroll down with the down arrow key to "Engine Settings" and press the right arrow Soft Key to enter.
5. Enter the password, which on the Soft Keys is MIDDLE-MIDDLE-LEFT-RIGHT.
6. Scroll down with the down arrow key to “Min RPM” and press the right arrow to enter.
7. Using the “-“ or “+” Soft Keys, adjust the setting to 1000 rpm.
8. Press the left “Exit” Soft Key to return to the Engine Settings Menu.
9281 LeSaint Drive Fairfield, Ohio 45014-5457 U.S.A.
[phone] 800-543-7166 Fax [phone] www.finncorp.com
Page 2of 6

TECHNICAL BULLETIN
No. 2015-0008
Date Released: December 2, 2015
9. Scroll down with the down arrow key to “Max RPM” and press the right arrow to enter.
10. Using the “-“ or “+” Soft Keys, adjust the setting to 2650 rpm.
11. Press the left “Exit” Soft Key to return to the Engine Settings Menu.
12. Scroll down with the down arrow key to “Throttle Type” and press the right arrow to enter.
13. Using the right “Change” Soft Key, cycle the setting to Ramp.
14. Press the left “Exit” Soft Key to return to the Engine Settings Menu.
15. Press the left “Exit” Soft Key to save all settings and return to the Main Menu.
16. Press the left “Exit” Soft Key again to return to the display mode.
17. Turn the key switch to "OFF".
Steps (MB50):
1. After display is installed, Turn the key switch to “ON”.
2. Press the engine start (ENG START) button on the key pad one time to turn on the fuel pump.
After the fuel pump has run, press and hold the engine start (ENG START) button until the engine
starts.
9281 LeSaint Drive Fairfield, Ohio 45014-5457 U.S.A.
[phone] 800-543-7166 Fax [phone] www.finncorp.com
Page 3of 6

TECHNICAL BULLETIN
No. 2015-0008
Date Released: December 2, 2015
3. On the display, press any key to activate the Soft Key menu.
4. Press the middle Soft Key with the wrench icon above it to access the Main Menu.
5. Scroll down with the down arrow key to "Engine Settings" and press the right arrow Soft Key to enter.
6. Enter the password, which on the Soft Keys is MIDDLE-MIDDLE-LEFT-RIGHT.
7. Scroll down with the down arrow key to “Min RPM” and press the right arrow to enter.
9281 LeSaint Drive Fairfield, Ohio 45014-5457 U.S.A.
[phone] 800-543-7166 Fax [phone] www.finncorp.com
Page 4of 6

TECHNICAL BULLETIN
No. 2015-0008
Date Released: December 2, 2015
8. Using the “-“ or “+” Soft Keys, adjust the setting to 1000 rpm.
9. Press the left “Exit” Soft Key to return to the Engine Settings Menu.
10. Scroll down with the down arrow key to “Max RPM” and press the right arrow to enter.
11. Using the “-“ or “+” Soft Keys, adjust the setting to 2350 rpm.
12. Press the left “Exit” Soft Key to return to the Engine Settings Menu.
13. Scroll down with the down arrow key to “Throttle Type” and press the right arrow to enter.
14. Using the right “Change” Soft Key, cycle the setting to Ramp.
15. Press the left “Exit” Soft Key to return to the Engine Settings Menu.
16. Press the left “Exit” Soft Key to save all settings and return to the Main Menu.
17. Press the left “Exit” Soft Key again to return to the display mode.
9281 LeSaint Drive Fairfield, Ohio 45014-5457 U.S.A.
[phone] 800-543-7166 Fax [phone] www.finncorp.com
Page 5of 6

TECHNICAL BULLETIN
No. 2015-0008
Date Released: December 2, 2015
18. Press the engine stop (ENG STOP) button on the key pad one time to turn off the engine.
19. Turn the key switch to "OFF".
* For any addit ional inform at ion please call t he Finn Service department at 1-800-543-7166 Ext . 226
9281 LeSaint Drive Fairfield, Ohio 45014-5457 U.S.A.
[phone] 800-543-7166 Fax [phone] www.finncorp.com
Page 6of 6