Fire Burglary Instruments STAR XL4600DL User manual

STAR XL4600DL
Hookup and Installation Instructions
A Subsidiary of Pittway Corporation
163, Eileen Way, Syosset, NY 11791
(800)6455430 .(516)92l-8666
FI2523Vl 2/9101990, FBX

STAR XL4600DL
TABLE OF CONTENTS
introduction ...................................................... 2
System Wiring and Hookup ........................... .3
Wiring Diagram ............................................ .3
Terminal Connections ................................... .4
VS279 Hookup.. ............................................ .5
679 Hookup .................................................. .5
Keypad Mounting ............................................. 6
System Components ........................................ 8
Keypad Layout ................................................. 9
System Operations .......................................... 11
PowerUp/System Reset,................................ 11
Arming..
......................................................... 11
Stay Arming................................................... 11
Instant Arming..
............................................. 1
1
Instant-Stay.. ................................................. 11
Disarming
...................................................... 11
Reset............................................................. 11
Bypass .......................................................... 11
Auto-Unbypass.............................................. 12
Manual Unbypass ......................................... 12
User Code Programming ............................. .12
Duress/Ambush............................................. 12
User Deletion ............................................... .13
Keypad Emergency Conditions.................... .13
System Programming ...................................... 14
Programmlng Questions ................................. 14
01 Primary Telephone Number.. ................... 14
02 Secondary Telephone Number.. ..............14
03 Callback Number .................................... .14
04 Dialer Options ......................................... .15
05 Keypad Conditions .................................. 17
06 Account Number 1 ................................... 17
07 Account Number 2 .................................. .17
08 System Timeouts .................................... .18
ZONE PROGRAMMING DESCRIPTION.. ........19
ZONE TYPE CHART.. ...................................... 20
09 ZONE #l ................................................ .21
10ZONE #2 ................................................. .21
11ZONE #3 ................................................. .21
12ZONE #4 ................................................. .21
13ZONE #5 ................................................. .21
14ZONE #6.. ............................................... .21
15AMBUSH/AC LOSS ................................ .22
16 Panic/Low Battery ................................... .22
17Open/Close, 24 Hr. Test ........................ .22
18 Bypass/Restore/Trouble/# Rings .............22
19 Keypad Fire/Keypad Aux ........................ .23
00 installer Code.. ........................................ .23
Data Entry Via LED Keypad ............................. 23
How To Enter Programming Mode................23
What You See On the Keypad.. ................... .23
Ready LED.............................................. .23
Zone LEDS.............................................. .23
System Status LEDS .............................. .24
How To Enter Data....................................... .24
Movement Between Questions.. ..............24
Movement Within Questions ....................24
Data Entry ............................................... .24
Question Acknowledgment ..................... .24
How To Exit Programming Mode..................25
Summary of System Programming ...............25
Data Entry Through XL4600LCDP Keypads .26
Zone Descriptor Programming .................... .27
System Defaults ............................................... 28
Programming Worksheet ................................ 30
STAR XL4600DL HOOKUP 81INSTALLATION Page 2

1. INTRODUCTION
m
The STAR XL4600DL is a state of the art EEPROM based control/communicator. The system features six fully
rogrammabie zones aswell as awired panic zone (orkeyswitch zone). Programming can be performed through the keypad
or the system can be uploaded and downloaded locally or remotely using the EZ-Mate programming devices. in addition,
remote control actions can be taken The STAR XL4600DL contains up to six user codes with capability for ambush code
and an arm only code. Ail of the keypads are four wire devices, with up to four keypads per system.
The XL4600DL can be used with the following keypads:
XL4600RM Flush Mount LED Metal Plate Keypad
XL4600RP Surface Mount LED keypad
XL46OOLCDPSurface Mount Plastic Keypad featuring two line LCD keypad with programmable zone descriptors.
2m
SYSTEM WIRING AND HOOKUP
2.1. SYSTEM WIRING DIAGRAM
STAR XL 4600DL
NOTES: A.
lo dxd la&r detaultvalues.remove all pwe! lpm system
(AC & DC). Neq shotl JPl 10JP2. wih shotl sail mtacl
reapply paver (AC tien DC wait 5 seconds lhen remove
inl
shon with power still apph
1. Connect lo a grounded cold waler pipe, 16 ga. al 15 feel.
2. Tolal AUX. power available is 500 mA. which indudes keypad power
3. Limited energy cable must be used
4. Sysun must be tosled on a woehly basis. For inlormabon roler to roloroncos.
5. Do not connect the banslormer to a receprade controlled by a switch.
6. Inslallauon cl equipmenl and wiring methods are required lo be in a~tdanca with
Ihe National Eleclrldans co& and ANSI/NFPA no 74. More inlormauon may ba
obwind from he NFPA. 8anory March Park. Quinsy. MA 02263
7- &not-y capacity lor Emergency Gcanooy is a minimum 014 hours Under normal
circumslzmces this barrory will last 3 years, use only exact replacemen&.
8. Maximum ol low keypads J-
FCC Regislralion~~umber AE396E-69554 AL-E Ringer Equivalence 0.081
l30lerenc.a~: Hook&nd Installation lnsaucaons l-2523 and Owners Manual I.2524
iALL NOT EXCEED 60
1 OTHER INITIATING
L BE CONNECTED TO
\
IRANSFOAUEA
THESE CIRCUI? ‘S UNLESS APPROVED
If, \\
RY TUF IWAI
I2UC LO“A I. . ..- ---..- AUTHORITY HAVING
UC&l,282 JURISDICTION cLY)ICnCITrTnP
WARNING
I
P
THIS UNIT INCLUDES AN ALARV
I
VERIFICATION FEATURE THAT WILL
ir0
RESlll T IN A DFI AY OF THE SYSTEM
.._-__ _ -__
ALARM SIGNAL FROM-THE INDICATED
I CIRCUITS. THE TOTAL DELA\r
I(011 CONTROL
b UNIT PLUS SMOKE
ETECTOR) Sk
SECONDS. NC
DEVICES SHAL
STAR XL46OODLHOOKUP 81INSTALLATION Page 3

2.2. TERMINAL CONNECTIONS
TERMINALS DESCRIPTION
1 at 2 (-)
Zone 1 (Requires 2.2K EOL resistor) [Default = DELAY]
2(-)&3
Zone 2 (Requires 2.2K EOL resistor) [Default = INTERIOR]
4 & 5(-)
Zone 3 (Requires 2.2K EOL resistor) [Default = PERIMETEO
5(-) & 6
Zone 4 (Requires 2.2K EOL resistor) [Default = PERIMETER). ’
7 & 8(-)
Zone 5 (Requires 2.2K EOL resistor) [Default = PERIMETER]
8(-) & 9
Zone 6 (Requires 2.2K EOL resistor) [Default = FIRE]
ZONE INFORMATION
10&13
11121314
Normally closed devices may be wired in series, and/or normally open devices
in parallel with the 2.2k ohm end of line resistor on all zones. The maximum
loop resistance may not exceed 100ohms. The loop response time is 280 ms
onallzones. Thefactory default values for eachzone is listed inthetable above,
however any zone can be programmed for the following types: Delay,
Perimeter, Interior, Fire, 24 Hr. Alarm, or 24 Hr. Trouble. Further explanation of
thezonetypes can befound inthe System Programming section ofthis manual.
PANIC CIRCUIT OR KEYSWITCH
Normally open circuit which can be programmed for use as either apanic circuit
or keyswitch input. If hardwired panic is programmed then this zone acts as a
24 hour zone which can be programmed for silent or audible operation. The
panic circuit will activated with each violation, therefore a latched device is
recommended. For UL installations, the panic switch connected to these
terminals is to be located no more than 3 feet from the control unit. If the
keyswitch option is selected then each activation of the keyswitch will arm and
disarm the system.
NOTE: E.O.L. resistor is not required on this zone.
KEYPADS:
15161718
19(+)20(-)
19(+)& 22(-)
A maximum of4 keypads, either XL4600RM, XL4600RP or XL4600LCDP, ma\-
bewiredto these terminals. The connections are asfollows; 11(GREEN =dati .,I
out), 12 (YELLOW = data in), 13 (BLACK = negative), and 14 (RED = positive
power). Each keypad draws approximately 30mA. Maximum keypad length is
500 feet using 22 gauge wire.
TELEPHONE LINE:
Connect the FBI1model368 cord asfollows; 15(GREEN = Telco Tip), 1G(RED
= Telco Ring), 17(BROWN= Home Tip), 18(GREY= Home Ring). Insert the
modular plugintoanapproved USOCRJ31Xjack (oraCA31Ajack for Canadian
installations).
The FCC registration number is (AE398E-69554 AL-E), and the ringer
equivalence is (O.OB).This STAR XL4600DL should not be connected to party
lines, or win operated phones.
Furthermore, this device should not be connected to a phone line which has
call waiting, unless the call waiting interrupt numbers are programmed into the
panel dialing sequence.
SMOKE DETECTOR POWER:
This system will accept 12VDC four(4) wire smoke detectors only.
Approximately 50mA of current is available at these terminals for powering all
detectors and an E.O.L. relay FBI1model 620. For UL installations see wiring
diagram for hookup.
These terminals adheretothe fire verification andreset logicwhich is explained
inthe Zone types section ofthis manual. Manual resetof smoke detector power
can be accomplished by entry of any valid user code after clearing alarm
memory.
REGULATED POWER (13.8VDC): f-7
. /’
Thetotal regulatedoutput powerfor motiondetectors andotherexternal devices
is 500mA at 13.8VDC, with less than 100 mVPP ripple.
STAR XL4600DL HOOKUP & INSTALLATION Page 4

21(+) & 22(-)
23
24 & 25
GROUNDING LUG
EARTH GROUND:
The total regulated output capacity of the XL4600DL includes the power
available from these terminals (19 & 22) as well as the power used by the
keypads andsmoke detectors. Therefore,todetermine thetotal power available
from these terminals subtract the power consumed by the keypads and smoke
detectors.
BELL OUTPUT:
The total output power available for sounding devices is 1.5 amps (1 Amp for
UL installations) at 13.8VDC. These terminals will deliver CONSTANT output
on BURGLARY, AUDIBLE PANIC and BELL TEST. On a FIRE condition, a
PULSED output will be generated. There are separate bell cutoff times
programmable for Burglary and Fire conditions within the programming
sequence.
679 Connection
679 XL4600.
a-@
@-@
0
3
vs 279 Connection
@-@
0
&@
4
ccl a-0
a Ohm
Speaker 5
5 m
a Ohm
Speaker
6
References: Model 679 l-2231 Model VS 279 l-2292
CONSTANT VOLTAGE OUTPUT
This terminal will deliver a constant unregulated voltage output (12VDC) for
devices requiring constant power such as the VS279 voice siren driver.
TRANSFORMER:
Connect an FBI1model 1282 12 VAC 40VA transformer, utilizing 18awg wire
at adistance notto exceed 15feet from the panel, to an unswltched 120 VAC
outlet.
Do not use any other transformer since this may result in improper operation or
damage to the unit.
The AC/LOW BAT LED on the keypad will remain ON, while AC power is
present. If an AC loss occurs the AC/LOW BAT LED will turn off immediately.
If AC remains OFF for 15 minutes, the system will pulse the keypad buzzer
andtransmit tothe central station, ifprogrammed. THE KEYPAD BUZZER CAN
BE SILENCED by entry of any valid user code. When AC restores the AC/LOW
BAT LED will light immediately, and a restore code will be reported, if
programmed.
Connect this grounding lug to a cold water pipe utilizing #18AWG wire at a
distance of no greater than 15ft.. If the premises pipes terminate in PVC, this
terminal must be connected to a six(6) foot grounding rod.
BACKUP BATTERY: The RED(+) and BLACK(-) flying leads must beconnected to a 12VDC 4-6AH
GELL CELL, to serve as backup power in the event of AC loss.
The XL4600DL performs a battery test approximately every 4.5 minutes. Low
battery condftion occurs at nominal 11VDC during this test. The keypad
AC/LOW BAT LEDandbuzzerwill PULSE SLOWLY when low battery condition
is detected. The system will report this condition to the CS if programmed.
Battery restoral will occur WITHIN 4.5 minutes, at the NEXT battery test. THE
BUZZER MAY BE SILENCED by entry of any valid user code.
GROUND FAULT
Ground fault capability can be added to the XL4600DL through addition of the
FBI1Model 117 module. Consult the 117 Installation Instructions for hookup
information.
STAR XL46OODLHOOKUP & INSTALLATION Page 5

3
. KEYPAD MOUNTING
3.1. XL4600RM METAL KEYPAD f-
FLUSH MOUNTING USING DOUBLE GANG BOX l- Create an opening and mount a standard
double gang box.
2- Secure keypad to double gang box as shown in
diagram below. Note:Thedouble gang box should
be mounted flush with the wall in order for the
keypad screws to fit.
NOTE: ForULinstallations, mountthe XL4600RM
to an earth grounded outlet box.
FLUSH MOUNTING WITH MOUNTING RING (Using the optional XL4600TR) I
1
I
l- Create the desired opening where keypad is to
be mounted, using the inside of the mounting ring
as a template. NOTE: This opening should be /
made between studs. 1
,
2- Secure mounting plate to wall through the four
outer holesusing suitable mounting hardware (no\7 I
provided). /
3- Connect keypad wiring to control panel and
secure the keypad to the mounting ring using the
four painted screws provided.
SURFACE MOUNTING (Using optional XL4600RMBX)
r
l- Depending on type of installation run the
keypad wiring out of the rear, top bottom or sides
of the backbox.
2- Attach backbox to wall at desired height
3- Insert XL4600RM keypad into backbox and
secure with the four screws provided.
STAR XL46OODLHOOKUP & INSTALLATION Page 6

MOUNTING KEYPAD IN CONTROL PANEL ENCLOSURE l- Remove keypad knockout from front ‘of metal
box enclosure as shown.
2- Insert XL4600RM into opening from front of
enclosure.
3- Secure keypad to enclosure using the four
painted metal screws and nuts provided.
3.2. XL4600RP or XL46OOLCDP PLASTIC KEYPADS
SURFACE MOUNTING l- Remove the plastic keypad section of the
keypad (right side) using a screwdriver in the slot
at the bottom of the keypad (see diagram).
2- Remove the zone indicator (left side) portion of
the keypad using ascrewdriver inthe slots located
on the left side of the keypad.
3- Connect keypad wiring to main control panel.
4- Remove the four screws which secure the
keypad to the rear mounting plate.
5 Secure the rear mounting plate to the wall
through any of the mounting holes provided.
6- Connect the 4600RP keypad to the mounting
plate through the four screws provided.
STAR XL4600DL HOOKUP &.INSTALLATION Page 7

4. SYSTEM COMPONENTS AND ACCESSORIES ’
The following configurations and accessories are available for the STAR XL4600DL system:
XL46OODL
XL4600RM
XL46OORP
XL46OOLCDP
XL4600TR
XL46OORMBX
DEMO4600
4600SLR
4600SLC
4600VU
7150
718ODL
7700
Includes XL46OODLcontrol panel, metal keypad (XL4600RM) and transformer.
Additional metal plate keypad for XL4600 system.
Additional surface mount keypad for XL4600 system.
Liquid Crystal Display (LCD) for the XL4600 system. This keypad contains a two line display which can
be programmed with customized 12character zone descriptors.
Mounhng Ring for flush mounting the XL4600RM keypad.
Back box to surface mount the XL4600RM metal keypad.
Sales Demonstration kit for the STAR XL 4600 system. This includes a working 4600 system, 4600RM
and 4600RP ke padsand can be used to demonstrate both residential and commercial ap Ircations.
Sales literature or residential applications. These brochures are 4 page, full color, and avai able in
r P
!iiackagesOf50.
ales rteraturefor commercial applications. These brochures are 4 page, full color, and available in
packages of 50.
End User Video tape for end user detailing the operation of the STAR XL-4600 system
EZ-Mate Programmer. Portable programming tool for the STAR product line (requires 7180DL cartridge)
Product cartridge for the XL4600DL providing local and remote uploadin
this cartridge performs remote commands (arm disarm bypass, system s
9 and downloading. In addition
atus etc).
EZ-Mate Downloader Soft\ivarewritten for IBM compatible systems for remote uploading/downloading
and device commands of Fire Burglary Instruments downloadable products.
STAR XL4600DL HOOKUP & INSTALLATION Page 8

5
n
KEYPAD LAYOUT
XL4600 RM
Keypad
XL 4600 Rf’
Keypad
1) ZONE STATUS LEDS
These LEDS display the current zone status including alarms, bypasses, troubles and faults. Each condition will cause
these LEDS to operate differently as follows:
ALARMS Fast Blink (approx. 150 ms. ON - 150 ms. OFF).
TROUBLES Slow Pulse (approx. 600 ms. ON - 600 ms. OFF).
BYPASSES Wink (100 ms. ON - 900 ms. OFF). Zone bypasses are displayed as a very slow wink of the
zone LED light.
FAULTED ZONES Solid ON. Faulted zones are the lowest priorit indication. Faulted burglary zones
are displayed with the LED solidly ON while the system is disarmecf.
NORMAL OFF
2) ARM/DISARM LED
This LED indicates whether the system is currently armed (ON) or disarmed (OFF). This LED will also blink fast to show
that alarms have occurred or blink slowly upon failure to communicate with the Central Station.
3) STAY LED
This LED displays whether the system has been armed in the STAY mode.
ON Interior zones are bypassed
OFF Interior zones are normal
4) INSTANT LED
This LEDdisplays whether the system hasbeenarmed inthe INSTANT mode, meaningthat the system iscurrently armed
and all delay zones are instant.
l
ON Delay zones are currently instant
---I OFF Delay zones are normal
5) AC/LOW BATTERY LED
This indicator light displays the current power status of the panel as follows;
STAR XL46OODLHOOKUP & INSTALLATION Page 9

ON AC is present
OFF No AC, running on battery backup
Slow Blink Low battery condition detected
6) READY LED fl
This LED displays whether the system is ready for arming. The READY light is common to all BURGLARY ZONES with’\- ’
the following indications;
ON System ready to be armed
OFF System not ready to be armed
Slow Blink Indicates Installer programming mode
Fast Blink Alarm Memory Mode
7) STAY BUlTON
The STAY mode enables arming the system, excluding zones programmed as interior zones. This will provide exterior
protection of the location while allowing full access throughout the interior.
8) BYPASS BUTTON
The BYPASS key is used to temporarily exclude protection to a specific zone.
9) INSTANT BUTTON
The INSTANT button enables arming of the system, eliminating the entry/exit delay.
10) CODE BUTTON
The CODE button is used to enter the installer programming mode and entry of user codes,
5.1. KEYPAD SOUNDER
The keypad sounder annunciates differently to indicate the following conditions:
CHIRP Keypad emits a short chirp to confirm each keystroke.
STEADY The keypad will make a steady sound during entry time, and/or during burglary alarm.
CHIME - steady 1 second tone.
ACKNOWLEDGE - Upon successful entry of a certain commands the system will emit a sound for
approximately half a second.
PULSING - A pulsing sound (approximately half a second ON then OFF) indicates a trouble condition
such as AC loss, Low Battery, or Fire Zone.
NEGATIVE ACKNOWLEDGMENT - Upon entry of an illegal command the keypad will emit four short
beeps. For example, if attempting to define a new user and the master user is not entered, four short
beeps WIIIbe made Indicating that the command was unsuccessful.
SOUNDER RINGBACK - Several short beeps to indicate successful communication to the Central
Statton. This occurs for all signals, excluding ambush and silent zones.
FAST PULSING SOUNDER- Sound
occurred and the system reached bel
?
enerated during entry time period AFTER an alarm condition has
cutoff. A pulsing sounder will follow the bell output on Fire
conditions. Trouble conditions also generate a pulsing sounder and will follow the loop or be silenced
through entry of a valid user code.
The keypad is non-operational if none of the LED’s are lit and the keypad does not beep when keys are pressed. This is
indication that service is required.
/
STAR XL46OODLHOOKUP & INSTALLATION Page 10

6
n $YSTEM OPERATIONS
6.1.
.a
POWER UP/SYSTEM RESET
Upon initial powerup of the XL4600DL , all of the lights on the LED keypad will go on and the sounder will operate for
approximately 10 seconds. This occurs on a total powerup , system reset or after completion of system programming. Ifthe
total system power is lost then upon power restoral, the XL4600DL will return to the previous arming state.
6.2. ARMING THE SYSTEM
FAIL-SAFE ARMING:
The XL46OODLcan be armed only if all burglary zones are good (not faulted) and the READY LED is on.
ARMING:
Enter any programmed four digit user code.
NOTE: The factory default user #l arming code is 1234.
The ARMED LED will light and the user may exit through an exit/entry zone for the time period programmed as the exit
delay. The XL4600DL can be armed without the backup battery being connected, however the AC/LB light will flash.
6.3. STAY ARMING
Depress the STAY BUTTON followed by a four digit user code.
The ARMED and STAY LEDs will light. The system is armed at this time with all programmed interior zones excluded.
6.4. INSTANT ARMING
Depress the INSTANT BUTTON followed by a four digit user code.
The ARMED and INSTANT LEDs will light. The system is armed at this time with all programmed delay zones instant.
6.5.
a
INSTANT-STAY ARMING
Depress the INSTANT then STAY buttons and a four digit user code.
The INSTANT STAY mode will arm the system with the characteristics of both the INSTANT and STAY modes. The
system will be armed with the interior zones bypassed and the delay zones instant.
6.6. DISARMING
Depress any valid four(4) digit user code.
The ARMED LED will extinguish.
If an alarm condition exists or hadoccurred while the system was armed, the respective zone(s) LED(s) and the READY
LEDwill be blinking rapidly. This condition is classified as ALARM MEMORY and can becleared through entry of avalid user
code.
6.7. RESET
Reset is accomplished through the entry of any valid user code. This can be used to reset the smoke detectors attached
to the system, silence any bells, or clear the keypad display or sounder.
In addition an option exists, for making the * key to act as a reset for clearing the sounder, communications failure, and
alarm memory. This programmable option can be obtained through location 3 of question 05.
6.8. BYPASS
Bypassing is performed to temporarily exclude zones which are faulty or not ready from activating the system.
Depress the BYPASS button followed by any valid four(4) digit user code, followed a number l-6, which represents the
respective zone to be bypassed.
EXAMPLE: BYPASS ZONE 2 (Assume user code of 1234)
BYPASS 1234 2
Subsequent bypasses can be made by depressing the BYPASS button followed by another zone number within a ten
second period. After this ten second period it will be necessary to enter the entire command including the user code.
After a successful bypass the keypad sounder will emit the acknowledge beep, and the respective zone LED will WINK
SLOWLY.
STAR XL4600DL HOOKUP & INSTALLATION Page 11

In addition the following rules for bypass exist;
l FIRE zones cannot be bypassed
l 24 hour zones can be bypassed, however they CANNOT be unbypassed if they are violated.
. Zones can only be bypassed while the system is disarmed, at which time visual indication will be displayed.
l Bypass.signals will be transmitted to the Central Station UPON ARMING if a bypass code has been
programmed.
NOTE: Zones which are bypassed are not protected when the system is armed.
6.9. AUTOUNBYPASS
All burglaryzones which arebypassed can be automatically unbypassed upon system disarm, assuming noother zone(s)
had been in alarm. 24 hour zones which have been bypassed will be unbypassed only if they are normal.
The autounbypass feature is a programmable option (see question 5 of the programming sequence.
6.10. MANUAL UNBYPASS,
The UNBYPASS function removes an existing bypass from a currently bypassed zone. The procedure is the same as
bypass.
6.11. USER CODE PROGRAMMING
Users codes can be entered or modified directly through the keypad.
The STAR XL4600DL contains up to six user codes (4 digits each) with the following applications;
ER NUMRER
APPJXXIX&l
1 MasterUser[Default= 12341
2
User#2 [Default= null]
3 User#3[Default= null]
4 User#4[Default= null]
5 User#5 [Default= null] NOTE: CanbeanAdM only code
6 AmbushCodeorUser#6 [Default = null]
NOTE: Only the master user (user number 1)can program or modify other users,
USER DEFINITION PROCEDURE:
CODE [USER] [USER#] [USERID]
where: CODE Code button on keypad
[USER] Master User ID code (user #l)
[USER#] Desired user to be programmed (1:S)
(USERID] Four digit user code. Valid digits are O-9
Example:
Define operator #3 with an ID of 7493. (Assume master user code is 1234).
CODE 1234 3 7493
An acknowledge sound (steady tone) verifies a successful user code programming.
A negative acknowledge sound (4 short tones) indicates unsuccessful programming.
If additional user programming is necessary, repeat the procedure listed above.
1User programming can be performed while the system Is DISARMED ONLY. 1
f”;
‘_ ,/
If a dialing format is programmed which transmits opening/closing by user ID, each user will report the respective user
number.
DURESS/AMBUSH
If ambush capability is required then an ambush transmission code must be entered within the programming sequence.,... /
When ambush has been enabled then the user #6 code will be used as an AMBUSH code. In this mode, entry of the user
#6code will ARM or DISARM the system andtransmit the ambush code to the Central Station. Furthermoreifopening/closing
by user reporting is programmed, user number 6 will be reported along with the ambush code.
STAR XL4600DL HOOKUP & INSTALLAT!ON Page 12

If ambush has not been programmed then user #6 can be used as an ordinary user code.
ARM ONLY CODE [USER 5 CODE]
A programming option exists to make user #5 an ARM only code. This means that the code can only arm the system and
would be used for a user such as a maid or temporary user of the system. This is obtained through location 2 of question 5.
.12. USER DELETION
Removal of users from the 4600 can be performed as follows;
USER DELETION PROCEDURE
CODE [USER] [User #] *
Where:
[USER] Master user code
[User #] Represents the user number being deleted.(2-6). Note: User number 1cannot be deleted.
l
is the l (asterisk) key from the keypad.
6.13. KEYPAD EMERGENCY CONDITIONS
The XL4600DL has the ability to transmit four separate keypad emergency conditions as follows:
PANIC
FIRE
AUX.
- AMBUSH
#’
79
13 -[USER CODE #6]
For example, the 24 hr keypad panic can be initiated through simultaneous depression of the # and l keys. The panic
condition can be silent (no bell output) or audible based on the programming option. NOTE: The default value for panic is
audible.
Audible panic can be RESET BY ENTERING ANY VALID USER CODE.
The keypad FIRE and AUX conditions are selectable through the programming sequence.
The ambush code will be user #6 if an ambush code is programmed in question #15.
STAR XL46OODLHOOKUP & INSTALLATION Page 13

/. SYSTEM PROGRAMMING
The STAR XL4600DL system can be programmed in any one of four methods;
l Directly through keypad (XL4600RM, XL4600RP, or XL4600LCDP)
l EZ-MATE PROGRAMMER model 7150 on-site. [Using model 7180DL Cartridge and the 7180J connector]
. EZ-MATE PROGRAMMER model 7150 remotely [Using model 7180DL Cartridge]
l EZ-MATE PC DOWNLOADER model 7700 remotely
/
I
This manual describes system programming via the keypad. The other programming products include documentation
/
describing their programming procedures.
Keypad programming is accomplished by understanding and compleiing the PROGRAMMING SHEET located on the
inside cover of this manual.
I
There are 19 total programming questions numbered 00-18. Additional programming questions are,available for the
programmable zone descriptors when the XL46OOLCDPis used. .
Within each question there are several locatiohs labeled Ll ,L2, etc. for data entry.
I
The XL46OODLis shipped from the factory with SPECIFIC DEFAULT VALUES which were selected for a typical
/
installation. Ifthe default values are suitable for your installation then programming can be simplified. The default values are
listed with each programming question and in the SYSTEM DEFAULT section of this manual.
8
. PROGRAMMING QUESTIONS STAR XL4600DL
This section ofthe manualdefines the programming questions alongwith the values expected for eachquestion. Complete
the Programming sheet-andthen enter the data through the keypad as explained inthe section titled Data Entry Through the
Keypad.
QUESTION 01 PRIMARY TELEPHONE NUMBER DEFAULk234AAAAAAAA.A - -.
Enterthe telephone number (including area code or dialing prefix IF NECESSARY) of the primary central station receiver p
in Ll - L12. , i,
Validdialingdigits areO-9,f3=’ ,andC=three second pause. An entry ofthe digit A signifies the endof the phone number.
REPORTING ROUTE:
/
The XL4600DL will report all signals to the primary receiver phone number. Furthermorethe panel will alternate between
I
the primary and secondary receivers (ifthe second phone number is programmed) for a maximum of 8 attempts each in the
;
event the signal has not been acknowledged.
QUESTION 02 SECONDARY TELEPHONE NUMBER DEFAULTzAAAAAAAAAAAA
Enter the telephone number (including area code or dialing prefix IF NECESSARY) of the secondary central station
receiver in Ll - L12.
Valid dialing digits areO-9,l3= l ,andC=three second pause. An entry ofthe digit A signifies the endofthe phone number.
The secondary telephone number will be used if the panel is unable to reach the Central Station via the primary number.
This is known as backup reporting.
Ifthe SPLIT REPORTING feature isprogrammed, then OPENING andCLOSING signals will bedirected to the secondary
CS number only, while all other conditions will be reported to primary number.
If neither split or backup reporting is necessary then this question may be left as factory defaulted and all conditions will
be routed to the Primary Telephone number only.
QUESTION 03 CALLBACK NUMBER DEFAULT: AAAAAAAAAAAA
Enterthe telephone number (including area code or dialing prefix if necessary) for this control panel to reach the callback
number location The callback number is the optional location of the EZ-Mate Programmer or Downloader where the control
panel will call during a remote communications (upload/download etc) session.
During remote communications the programming device and the 4600DL control panel will first confirm the CS security r”\
code. If valid, communications can begin. If a callback number is defined, the control panel will the hang up and dial the I
callback number.
For nocallback capability enter AAAAAAAAAAAA.
STAR XL4600DL HOOKUP & INSTALLATION Page 14

QUESTION 04- DIALER OPTIONS
There are 4 locations (Ll -L4) within this question which define various dialer and system options as follows:
Ll = Dialer Formats
L2 = Receiver Type
0 L3 = Message length (ie:3xl,4x1,4x2)
L4 = System Options (Panic Type, Split Reporting, 24 Hr Test, Bell Test)
L 1 DIALER FORMATS
DEFAULT: 1
Enter the digit for the desired dialer format from the chart below in location Ll ;
0 Pulse Dialing, Standard Format or 4X2
1 Touch Tone Dialing, Standard format or 4X2
2 Pulse Dialing, Extended Format
3 Touch Tone Dialing, Extended Format
4 Pulse Dialing, Partial Extended Format
5 Touch Tone Dialing, Partial Extended Format
8 No Dialer (Local Alarm only)
FORMAT EXPLANATIONS
Standard
Standard format involves a 3 or 4 digit account number followed by a single round event code. Examples:
1233
or
6548 2
Extended
Extended format (sometimes known as universal or expanded format) transmits two rounds of
informatron.The frrst round includes the account number and an expansion character while the second
round repeats the expansion digit as account number before identifying the zone code.
For example;
1233
333 1
or
4312 E
EEEE 7
PARTIAL EXTENDED
The partial extended format transmits a standard signal for alarm conditions and an extended message
for restores and other system conditions. NOTE: The extended message codes must be B-F).
Example:
Alarm Condition
853 1
Restore
853 E
EEE 1
STAR XL4600DL HOOKUP & INSTALLATION Page 15

L2 RECEIVER TYPE DEFAULT = 6
Enter the digit for the desired receiver type from the chart below in location L2.
VALUE DESCRIPTION TYPICAL CS RECEIVERS
o= 10 PPS, 1400 Hz., No Parity FBI, Ademco Slow, Silent Knight Slow
l= 10 PPS, 1400 Hz, Parity FBI
2= 10 PPS, 2300 Hz, No Parity FBI
3= 10 PPS, 2300 Hz, Parity FBI
4= 20 PPS, 1400 Hz, No Parity FBI, Silent Knight Fast, ADCOR, ADEMCO 685
5= 20 PPS, 1400 Hz, Parity FBI, Radionics Slow (1400)
6= 20 PPS, 2300Hz., No Parity FBI, Franklin, Sescoa, DCI, Quickalert, Varitech, ADEMCO 685
7= 20 PPS, 2300 Hz, Parity FBI, Radionics Slow (2300)
8= 40 PPS, 1400 Hz, No Parity FBI
A= 40 PPS, 2300 Hz, No Parity FBI
B= 40 PPS, 2300 Hz, Parity FBI, Radionics Fast (2300)
NOTE: For UL installations the acceptable receivers are FBI CP220 (all formats), ADEMCO 685 (all formats without
parity), Silent Knight 8520 or 9000.
L3 - MESSAGE LENGTH/BELL LOCKOUT Default = 1
r
Enter the digit for the desired message length from the chart below in location L3.
o= 3 x 1 3 digit account, 1dlglt event code, no bell lockout 8 = 3x1, with bell lockout
2
fjf
4x1 4 digit account number, 1digit event code, no bell lockout A = 4x1, with bell lockout
4 x 2 4 digit account number, 2 digit event code, no bell lockout E = 4x2, with bell lockout
If bell lockout is selected then subsequent activations of the same zone within the same arming interval will not activate
the bell. This applies only to burglary (non 24 hour) zones. For UL installations bell lockout must not be selected.
NOTE: Please consult your Central Station manager to determine the formats and message lengths which are accepted
by the receiver. To select European dialing format, add 1to the value selected for this digit.
L4- SYSTEM OPTIONS Default = 1
Enter the digit for the desired system options from the chart below in location L4.
o= Silent Keypad Panic
1 Audlble Keypad Panic r
2:
Silent Keypad Panic, Split Reporting
3
41 Audible Keypad Panic, Split Reporting
Silent Keypad Panic, 24 Hr Test
5= Audible Keypad Panic, 24 Hr Test
6= Silent Keypad Panic, Split Reporting, 24 Hr Test
7= Audible Keypad Panic, Split Reporting, 24 hr Test
8= Silent Keypad Panic, Bell Test
9= Audible Keypad Panic, Bell Test
A= Silent Keypad Panic, Split Reporting, Bell Test
B= Audible Keypad Panic, Split Reporting, Bell Test
c= Silent Keypad Panic, 24 Hr Test, Bell Test
D= Audible Keypad Panic, 24 hr Test, Bell Test
E= Silent Keypad Panic, Split Reporting, 24 Hr Test, Bell Test
F= Audible Keypad Panic, Split Reporting, 24 Hr Test, Bell Test
DESCRIPTION OF SYSTEM OPTIONS
Keypad SllentlAudlble Panic - Determines whether the keypad panic condition ( ’ & #from the keypad) will activate
the bell. In either case a signal will be transmitted to the Central Station if a panic code has been programmed. NOTE: The
keypad panic condition can be activated through location 1of question 05.
Split Reporting -The split reportingoptionwill direct allopeningandclosing signalstothe secondary receivertelephone
number. All otherconditions (alarms, troubles, restores etc.) will adhereto the reporting routedescribed inquestion 01.If split
reporting is selected then the secondary receiver telephone number MUST be programmed.
24 Hour Test - If 24 hourtest is enabled then the XL46OODLwill transmit the test code to the Central Station every 24
hours inthe absence of anyother signal. Transmission of any signalwill resetthe 24 hourtest clock. Forexample ifa businessr
opened and closed 6 days a week then a test signal will be generated 24 hours after the last closing signal. NOTE: This
option is requiredfor UL Commercial Burglary applications. ‘.
Bell Test If this option is selected the bell will be activated for one second upon successful arming. This option is
required for UL Commercial Burglary applications.
STAR XL4600DL HOOKUP & INSTALLATION Page 16

QUESTION 05 KEYPAD CONDITIONS DEFAULT = 1400
This question contains four locations for various keypad definable options
L 1 - KEYPAD EMERGENCY CONDITIONS DEFAULT = 1
a
This location specifies which of the keypad emergency conditions are active. To determine the value for this location add
the values for the desired conditions as shown inthe chart below:
VALUF CONDITIQJj
+l Keypad Panic (
l & #) Enable
+2 Keypad Fire (7 & 9) Enable
+4 Keypad Aux (1 & 3) Enable
+8 Keypad Aux = Audible
Forexample, if you wanted the keypad panic andfire conditions only then add +l and +2 ,and enter a3 into this location.
The valid selections for this digit are shown below;
0 = Keypad Emergency Conditions Disabled
1 = Keypad Panic
2 = Keypad Fire
3 = Keypad Panic, Keypad Fire
4 = Keypad Aux (Silent)
5 = Keypad Panic, Aux (Silent)
6 = Keypad Fire, Aux. (Silent)
7 = Keypad Panic, Fire, Aux (Silent)
C = Keypad Aux. (Audible)
D = Keypad Panic, Aux. (Audible)
E = Keypad Fire, Aux. (Audible)
F = Keypad Panic, Fire, Aux (Audible)
L2 - MISC OPTIONS DEFAULT = 4
0
To obtain the value for this location add the values corresponding to the desired options or consult the table:
PANIC or KEYSWITCH (+l)
This option determines whether connections 10 & 13 on the control panel will be used as a panic input or a keyswitch
input. Note :Add 1 if a keyswitch is desired.
HARDWIRED PANIC SILENT or AUDIBLE (+2)
Determines whether the hardwired panic circuit will be audible or silent. NCTE: Add 2 if audible.
AUTO-UNBYPASS ENABLE (+4)
Determines whether zones will automatically be unbypassed upon disarm. Add 4 for autounbypass enable.
ARM ONLY CODE [USER #5] (+8)
If user number 5 should be used as an arm only code (maid code) then add 8 to this digit.
The valid selections for this digit are shown below:
0 = Panic Input Silent
1 = Keyswitch Input
2 = Panic Input Enabled Audible
4 = Panic Input Silent, Auto-unbypass
5 = Keyswitch Input , Auto-unbypass
6 = Panic Input Audible, Auto-unbypass
8 = Panic Input Silent, Arm Only User 5
9 = Keyswitch Input, Arm Only User 5
A = Panic Input Audible, Arm Only User 5
C = Panic Input Silent , Auto-unbypass, Arm Only User 5
D = Keyswitch Input, Auto-unbypass, Arm Only User 5
E = Panic Input Audible, Auto-unbypass, Arm Only User 5
STAR XL4600DL HOOKUP & INSTALLATION Page 17

L3 QUICK COMMANDS - RESET
This location determines whether the quick commands are enabled as shown below:
0 = Quick Commands Dlsabled
1= Quick Forced Arm
2 = Quick Arm
3 = Quick Forced Arm, Quick Arm
4 = Reset Enable
5 = Quick Forced Arm, Reset Enable
6 = Quick Arm, Reset Enable
7 = Quick Forced Arm, Quick Arm, Reset Enable
QUICK FORCED ARM ENABLE (+l)
Specifies whether quick forced arm (#key followed bythe 2 key from the keypad) will be permitted. Ifquick forced arming
is permitted then user #7 code will be reported to the CS if a two digit transmission is defined.
QUICK ARM (+ 2)
Specifies whether quick arming ( # key followed by the 1 key from the keypad) will be permitted. Quick arming allows
armingof the system without entry of a user code and if permitted will report user #7 code to the CS if atwo digit transmission
is defined.
RESET ENABLE (+4)
This option will allow entryof a l from the keypad to resetthe following conditions: soundercommunications failure ,alarm
memory.
QUESTION 06 ACCOUNT NUMBER 1 DEFAULT = 1234
Enterthe three(3) or four(4) digit subscriber account number for Central Station phone number 1 in locations Ll -L4.
If a three(3) digit number is used then enter an A in location L4.
Valid entries are O-9,and B-F. The value A is interpreted as the null value for account numbers.
QUESTION 07 ACCOUNT NUMBER 2 DEFAULT = AAAA
Enterthe three(3) or four(4) digit subscriber account number for Central Station phone number 2 in locations Ll -L4.
If a three(3) digit number is used then enter an A in location L4.
Valid entries are O-9,and B-F. The value A is interpreted as the null value for account numbers. /-
Ifthe second phone number is not used this question can be left as factory defaulted.
THIS ACCOUNT NUMBER MUST BE ENTERED IF YOU HAVE PROGRAMMED A SECOND RECEIVER PHONE
NUMBER FOR BACKUP OR SPLIT REPORTING.
QUESTION 08 SYSTEM TIMEOUTS
There are 4 locations (Ll-L4) within this question which define various system timing options as follows:
CATIONS DEFAUI TS
Ll = Entry Delay 30 seconds
L2 = Exit Delay 60 seconds
L3 = Burglary Bell Cutoff 15 minutes
L4 = Fire Bell Cutoff No Cutoff
Ll - ENTRY DELAY Default = 2
Enterthe desired entry delay time in 15second increments. The valid rangeof input is 1- F,with 1indicating a 15second
entry delay and F indicating 225 seconds. For UL applications the maximum entrance delay shall not exceed 45 seconds for
household applications or 15 seconds for commercial burglary applications.
L2 - EXITDELAY Default = 4
Enter the desired exit time in 15 second increments, For UL applications the maximum exit delay shall not exceed 60
secondsThe valid range of input is 1 - F,with 1 indicating a 15second exit delay and F indicating 225 seconds.
L3 - BURGLARY BELL CUTOFF Default = 5
Enterthe desired bell cutoff time on alarm conditions for burglary and panic in 3 minute intervals. The valid range of input
is 1 - F,with F indicating an infinite burg bell cutoff, Example 3 = 9 minutes. For UL installations in commercial applications
the minimum bell cutoff shall be 15 minutes, or 4 minutes for household burglary applications.
L4 - FIRE BELL CUTOFF Default = F f-
Enter the desired bell cutoff time for fire conditions in three minute intervals. The valid range of input is 1 - F, with F~
indicating an infinite fire bell cutoff. Example 3 = 9 minutes. For UL installations the minimum fire bell cutoff time shall be 4
minutes.
STAR XL46OODLHOOKUP & INSTALLATION Page 18

8.1. ZONE PROGRAMMING
Questions 09-l 4 represent all the options related to programmable zones l-6. Each question contains four(4) locations
Ll -L4.Thefirsttwo locations (Ll -L2)definethe zone type. The secondtwo locations (L3-L4)definethe alarmcodetransmitted
to the Central Station for that zone.
a ZONE TYPES
Zones l-6 can be programmed for any one of the following zone types:
BURGLARYZONES
DELAY
INTERIOR
PERIMETER
BURGLARY ZONE OPTIONS
RESTORE
CHIME
DIALER DELAY
DAY FEATURE
24 HR ZONES
FIRE
This is the industry standard exit/entry zone. When the system is armed exit
time begins. After exit expires, any subsequent violation of this zone will begin
entry time. Ifthe system is not disarmed within the programmed entry time an
alarmwill occur. Thekeypad sounderwill annunciate steadily during entrytime,
unless there had been an alarm condition, at which time it will pulse. Delay
zones will activate instantly when the system is armed using the INSTANT
mode.
All interior zones have exit delay time upon system arming. Furthermore, all
interior zones will have entry delay time if a delay zone is violated first. If this
zone is violated first howeverjt will generate an immediate alarm. :
Interiorzones will automatically bebypassed ifthe system isarmedin the STAY
MODE.
This zone type (sometimes known as INSTANT) will generate an alarm when
violated.while the system is armed.
Ifthis option is selected on a burglary zone, then the programmed restore code
will bereporteduponbellcutoff, assuming the loopis restored.The restorecode
will also be reported if the system is disarmed during an alarm.
Ifthis option is selected the keypad sounder will annunciate for 1second when
this zone is violated in the disarmed mode.
Ifthis option is selected the system will allow a 15 second delay before dialing,
allowing the end userto ABORT the transmission. Ifthis option is not selected,
any alarm condition will result in an immediate transmission that cannot be
aborted. NOTE: For UL installations dialer delay may not be used.
Ifazone with this option isviolated while the system is DISARMED, the keypad
sounderandzone LEDwill pulsefor as longasthe violation remains. Inaddition,
the SYSTEM TROUBLE CODE will be transmitted to the central station. THE
SOUNDER CAN BE SILENCED through entryoperation of anyvaliduser code.
While the system is armed, a DAY zone will act as an alarm when violated.
FIRE zones on the XL46OODLcontain Fire Verification Logic. Upon detection
ofthefirst violation, smoke detector powerwill be resetfor aperiodof8seconds.
After this time period, power is restored. Fora period of 5 seconds the fire zone
will not be scanned allowing the smoke detectors to settle. Future violations
within a two minute period will result in a PULSING BELL OUTPUT, RAPID
PULSING ZONE LED,and IMMEDIATE transmission to the CS. Fire signals
cannot be aborted. .. .
Entry of any valid user code will silence the sounder, bell and reset smoke
detector power. If the system detects that the fire zone is still violated within 2
minutes of power reset, the zone LEDwill pulse slowly to indicate afire trouble.
Thereafter, smoke detector power will be reset every 4 minutes automatically
in an attempt to clear the fire zone.
Inthe eventthe fire zone experiences anopen, the system indicates fire trouble
by pulsing the keypad zone LED and sounder slowly. The system trouble code
( followed by the zone code ) will be reported to the CS.
The keypad sounder can be SILENCED through entry of ANY VALID USER
CODE.
STAR XL4600DL HOOKUP & INSTALLATION Page 19

24 HR ALARM
NOTE: FIRE ZONES can not be bypassed.
This zone type is always active, independent of the system arming status.
Programming options include audible (STEADY BELL) or silent (NO BELL or
keypad indications), with or without restore codes. Upon violation the zone
LEDSwill pulse rapidly (audiblezones only) andan immediate CStransmission
will occur which cannot be aborted. 0
24 Hour Alarm zones can be bypassed, however they cannot be unbypassed
if a violation exists on the zone terminals.
24 HR TROUBLE
This zone type is always active, independent of the system arming status.
Programming options include audible (PULSING KEYPAD SOUNDER) or
silent, with or without restore codes. Upon violation the zone LED will pulse
slowly. Trouble condition must exist for 15 seconds before a transmission will
occur. The keypad display and sounder will clear upon zone restoral.
24 Hour Trouble zones can be bypassed, however they cannot be unbypassed
if a violation exists on the zone terminals.
THE SOUNDER MAY BE SILENCED THROUGH ENTRY OF ANY VALID
USER CODE.
ZONE CHART
The following table contains the entries required for locations Ll and L2 of the zone type questions;
.i!ONETYPES
CONTROLLED ZONES
10 Perimeter
11 Perimeter, Reslore
12 Perimeter. Day
13 Perimeter, Day, Restore
14 Perimeter, Chime
15 Perimeter. Chime, Reslore
18 Perimeler. Dial Delay
19 Perimeter, Restore, Dial Delay
1A Perimeler. Day, Dial Delay
1B Perimeter, Day, Restore. Dial Delay
1C Perimeter, Chime, Dial Delay
1D Perimeter, Chime, Restore. Dia! Delay
24 HOUR ZONES
20 Delay 81 Alarm Audible
21 Delay, Restore 89 Alarm Silent
24 Delay, Chimo (no LED , sounder, bell)
25 Delay. Chime, Restore 91 Alarm, Restore
40 Interior 99 Hold-Up, Restore
41 Interior. Resfore BA Trouble, Silent
44 Interior Chime (LED indicalion only)
45 Inlerior. Chime, Restore 92 Trouble.Audible.Restore
48 Inlerior. Dial Delay 84 Fire
49 Interior. Restore. Dial Delay 94 Fire, Restore
4C Interior. Chime, Dial Delay
40 Inlerior,, Chime.Restore, Dial Delay
ZONE ALARM CODES
As previously specified locations L3 and L4 of the zone questions represent the alarm code that will be reported to the
central station.
Zones will transmit to the Central Station unless these digits are defined as AA for any individual zone, or the local dialer
option is selected in question 03. Based on the dialer format selected enter the alarm code as follows;
STANDARD FORMAT: Enterthe desired single digit alarm code in location L3. The value placed in L4
will not be used.
Example: Desired transmission 123 2 (account 123, alarm code 2).
Enter a 2 in location L3 of the zone. Any value placed in L4will be not be used.
EXTENDED:Enter the desired first digit of the alarm code in location L3. The second digit in L4.
Example: Desired transmission 1233
333 4
Enter 3 in L3, 4 in L4.
r‘
\
STAR XL4600DL HOOKUP & INSTALLATION Page 20