FireplaceXtrordinair 44 DV XXL EF User manual

TM
Tested and Listed by
OMNI-Test Laboratories, Inc.
Beaverton, Oregon
Report #
ANSI Z21.88
• Built-In Direct Vent Fireplace
• Natural Gas or Propane
• Residential or Mobile Home
WARNING: If the information in these instructions are not followed exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
• Installation and service mustbe performed by a qualified installer,service agency or the gas
supplier.
This appliance may be installed as an OEM installation in a manufactured (mobile) home and
must be installed in accordance with the manufacturer’s instructions and the manufactured
home construction and safety standard, Title 24 CFR, Part 3280 or Standard for Installation in
Mobile Homes, CAN/CSA Z240 MH.
This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion
kit is supplied with the appliance.
44 DV XXL EF Manual
Installer: After installation give this manual to the home-owner
and explain operation of this heater.
Copyright 2007, Travis Industries $10.00 100-01149
4800 Harbour Pointe Blvd. SW
Mukilteo, WA 98275

2Introduction
Travis Industries 4050114 100-01149
Introduction
We welcome you as a new owner of a Fireplace Xtrordinair gas fireplace. In purchasing a Fireplace Xtrordinair
you have joined the growing ranks of concerned individuals whose selection of an energy system reflects
both a concern for the environment and aesthetics. The Fireplace Xtrordinair is one of the finest home
heaters the world over. This manual will explain the installation, operation, and maintenance of this fireplace.
Please familiarize yourself with the Owner's Manual before operating your heater and save the manual for
future reference. Included are helpful hints and suggestions that will make the operation and maintenance of
your new fireplace an easier and more enjoyable experience. We offer our continual support and guidance to
help you achieve the maximum benefit and enjoyment from your heater.
Important Information
No other Fireplace Xtrordinair gas fireplace has the
same serial number as yours. The serial number is
below and to the left of the gas control valve.
This serial number will be needed in case you require
service of any type.
Model: 44 DV XXL EF
Serial Number:
Purchase Date:
Purchased From:
Mail your Warranty Card
Today, and Save Your Bill of
Sale.
To receive full warranty coverage,
you will need to show evidence of
the date you purchased your
heater. Do not mail your Bill of
Sale to us.
We suggest that you attach your
Bill of Sale to this page so that you
will have all the information you
need in one place should the need
for service or information occur.

Safety Precautions 3
Travis Industries 4050114 100-01149
Introduction
Introduction & Important Information................2
Safety Precautions
Safety Precautions......................................4
Features & Specifications
Features ....................................................6
Installation Options......................................6
Heating Specifications..................................6
Dimensions.................................................6
Installation
Installation Warnings....................................7
Packing List................................................7
Additional Items Required for Installation..........7
Installation Overview....................................8
Recommended Installation Procedure..............8
Fireplace Placement Requirements..................9
Minimum Framing Dimensions ....................9
Clearances ............................................10
Vertical Stand-Off...................................10
Corner Installations .................................11
Raised Fireplaces....................................11
Gas Line Requirements.................................12
Fuel......................................................12
Gas Line Connection................................12
Gas Inlet Pressure ..................................12
Electrical Connection....................................13
Vent Requirements.......................................14
Altitude Considerations ............................14
Clearances ............................................14
Part Numbers (8" Dia. Pipe) .......................14
Vent Installation......................................15
Approved Vent Configurations........................16
Restrictor Position...................................16
Elbows..................................................16
Measuring Vent Lengths...........................16
Vertical Term. 0,2 or 4 45° Offsets ..............17
Horizontal Term. with One Vert. Elbow .........18
Horizontal Term. with Three Vert. Elbows......19
Vertical Term. with Two Elbows...................20
Vent Termination Requirements ......................21
Hearth Requirements....................................22
Facing Requirements....................................23
Face Dimensions .........................................24
Fireplace Facing Detail..................................25
Facing Example – Facing Under 1” Thick...........26
Facing Example – Facing Over 1” Thick ............27
Mantel Requirements....................................28
Finalizing the Installation
1 Glass Removal (& installation)......................29
2 Log Installation .........................................31
3 Replace the Glass .....................................35
4 Faceplate Installation.................................35
5 Leak Test.................................................35
6 Pilot Adjustment (if necessary).....................35
7 Air Shutter Adjustment (if necessary)............35
8 Check Flame.............................................35
9 Explain Operation to Home-Owner.................36
Operation
Before You Begin.........................................37
Location of Controls .....................................37
Starting The Pilot .........................................38
Starting the Fireplace for the First Time.............39
Turning the Fireplace On and Off.....................39
Adjusting the Flame Height.............................39
Adjusting the Blower Speed............................40
Optional Power Heat Duct Operation................40
Normal Operating Sounds..............................40
Normal Operating Odors................................40
Maintenance
Yearly Service Procedure..............................41
Troubleshooting Table...................................42
How this Fireplace Works...............................43
What Turns the Main Burners On and Off......43
What Prevents Gas Buildup.......................43
Wiring Diagram ............................................44
Replacement Parts List.................................44
Safety Label
Safety (Listing) Label....................................45
Warranty
Warranty....................................................46
Optional Equipment
LP Conversion Kit ........................................47
Power Heat Duct..........................................50
Modulating Remote Installation.......................55
Index
Index.........................................................56

4Safety Precautions
Travis Industries 4050114 100-01149
4
• IF YOU SMELL GAS:
* Do not light any appliance
* Extinguish any open flame
* Do not touch any electrical switch or plug or unplug anything
* Open windows and vacate building
* Call gas supplier from neighbor's house, if not reached, call fire
department
• This unit must be installed by a qualified installer to prevent the
possibility of an explosion. Your dealer will know the requirements in
your area and can inform you of those people considered qualified. The
room heater should be inspected before use and at least annually by a
qualified service person. More frequent cleaning may be required due
to excessive lint from carpeting, bedding material, etc.
• The instructions in this manual must be strictly adhered to. Do not use makeshift
methods or compromise in the installation. Improper installation will void the warranty and
safety listing.
For LPG only | Pout 11” W.C.
Look for this label:
If the label is present, the
heater is equipped for LP
(propane). If the label is
absent, the heater is equipped
for NG (natural gas).
•This heater is either approved for natural
gas (NG) or for propane (LP or LPG).
Burning the incorrect fuel will void the
warranty and safety listing and may cause
an extreme safety hazard. Direct
questions about the type of fuel used to
your dealer. Check for the label shown to
the right.
Ok
•Contact your local building
officials to obtain a permit
and information on any
installation restrictions or
inspection requirements in
your area. Notify your
insurance company of this
heater as well.
•If the flame becomes sooty,
dark orange in color, or
extremely tall, do not
operate the heater. Call
your dealer and arrange for
proper servicing.
AAA
AA
AA
•It is imperative that control
compartments, screens, or
circulating air passageways
of the heater be kept clean
and free of obstructions.
These areas provide the air
necessary for safe
operation. ?•Do not operate the heater if
it is not operating properly in
any fashion or if you are
uncertain. Call your dealer
for a full explanation of your
heater and what to expect.
Gas
•Do not store or use gasoline
or other flammable liquids in
the vicinity of this heater.
AAA
AA
AA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
A
A
•Do not use this appliance if
any part has been under
water. Immediately call a
qualified service technician
to inspect the appliance and
to replace any part of the
control system and any gas
control which has been
under water.

Safety Precautions 5
Travis Industries 4050114 100-01149
AAA
AA
AA
•Do not place clothing or
other flammable items on or
near the heater. Because
this heater can be controlled
by a thermostat there is a
possibility of the heater
turning on and igniting any
items placed on or near it.
AA
AA
AA
AA
A
•Light the heater using the
built-in piezo igniter. Do not
use matches or any other
external device to light your
heater.
•Never remove, replace,
modify or substitute any part
of the heater unless
AAA
AA
AA
AA
AA
•The viewing glass should be
opened only for lighting the
pilot or conducting service.
•Any safety screen or guard
removed for servicing must
be replaced prior to
operating the heater.
•Do not operate with the
glass removed or damaged.
instructions are given in this
manual. All other work must
be done by a trained
technician. Don't modify or
replace orifices.
•Allow the heater to cool
before carrying out any
maintenance or cleaning.
•Operate the heater
according to the instructions
included in this manual.
•If the main burners do not
start correctly turn the gas
off at the gas control valve
and call your dealer for
service.
•The pilot flame must contact
the thermopile and
thermocouple (see the
illustration to the left). If it
does not, turn the gas
control valve to "OFF" and
call your dealer.
AAA
AA
AA
A
A
A
A
•This unit is not for use with
solid fuel
•Do not place anything inside
the firebox (except the
included fiber logs).
•If the fiber logs become
damaged, replace with
Travis Industries log set.
This
Manual
•Do not throw this manual
away. This manual has
important operating and
maintenance instructions
that you will need at a later
time. Always follow the
instructions in this manual.
AAA
AA
AA
•Do not touch the hot
surfaces of the heater.
Educate all children of the
danger of a high-
temperature heater. Young
children should be
supervised when they are in
the same room as the
heater.
•Travis Industries, Inc.
grants no warranty,
implied or stated, for
the installation or
maintenance of your
heater, and assumes
no responsibility of any
consequential
damage(s).
•Instruct everyone in the
house how to shut gas off to
the appliance and at the gas
main shutoff valve. The gas
main shutoff valve is usually
next to the gas meter or
propane tank and requires a
wrench to shut off.

6Features and Specifications
Travis Industries 4050114 100-01149
6
Features:
- Works During Power Outages (millivolt system)
- High Efficiency
- Optional Thermostat or Remote Control
- Realistic "Wood Fire" Look
- Two Quiet Blowers for Effective Heat Distribution
- Convenient Operating Controls
- Variable-Rate Heat Output
- Low Maintenance
Installation Options:
- Residential or Mobile Home
- Straight or Corner Placement
- Flush or Recessed Face
- Raised or Floor Hearth
- Internal or External Chase
- Horizontal or Vertical Vent
- Power Heat Duct
Heating Specifications: Natural Gas Propane
Approximate Heating Capacity (in square feet)* Up to 3,000 Up to 3,000
BTU Input Per Hour (from high to low) 58, 000 –43,000 58, 000 –44,000
BTU Output on High (with blowers on) 42,920 44,080
Efficiency** (with blowers on) 74 % 76 %
AFUE (Annual Fuel Utilization Efficiency) 68 % 69 %
* Heating capacity will vary with floor plan, insulation, use of Power Heat Duct, and outside temperature.
** Efficiency rating is a product thermal efficiency rating determined under continuous operation independent of installed system.
The electrical connection is made
in the lower right rear corner.
24-1/8"*
51-3/4"*
1" Stand-offs
* Includes the required 1"
clearance.
Nail Down Plate (used
to secure the fireplace
to the floor)
8-7/8"*
Vent has an external diameter of 8"
Weight: 325 Lbs.
Dimensions:
Gas Inlet (on both sides)
1"
6-1/4"
10-1/2"
42-3/4"
31-3/8"
3-7/8"
7-5/8"
27-1/2"
27-5/8"
1"
6-1/2"
2-3/8"
5-3/8"*
5-1/4"* 37-7/8"*
4-1/16"
40"
WARNING:
A 1" clearance from the
fireplace enclosure is
required along the sides
and back of the fireplace.
Power Heat
Vent Hook-Up
Thermostat Wire Hole
(on both sides)

Installation (for qualified installers only) 7
Travis Industries 4050114 100-01149
Installation Warnings:
! Failure to follow all of the requirements may result in property damage, bodily injury, or
even death.
! This heater must be installed by a qualified installer who has gone through a training
program for the installation of direct vent gas appliances.
! This appliance must be installed in accordance with all local codes, if any; if not, in
U.S.A. follow ANSI Z223.1 and NFPA 54(88).
! In Manufactured or Mobile Homes must conform with: In USA, Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280. This appliance may be
installed in Manufactured Housing only after the home is site located.
! The 44 DV XXL is designed to operate on natural gas or propane (LP).
! All exhaust gases must be vented outside the structure of the living-area. Combustion
air is drawn from outside the living-area structure.
! Notify your insurance company before hooking up this fireplace.
! The requirements listed below are divided into sections. All requirements must be met
simultaneously. The order of installation is not rigid –the qualified installer should
follow the procedure best suited for the installation.
Packing List
•Propane Conversion Kit
•Log Set (Log Set, Coals, & Glowing Embers)
•Flex Tube with Pipe Adapter
•Glass Latch Key (to un-latch glass frame)
•Arch Covers (for arched face)
•Firestop (manufactured for the 44 DV XXL)
•(2) Fireback Clips (for ceramic firebacks only)
Additional Items Required
•Faceplate - Includes attachment screws
•Direct Vent (Simpson Dura-Vent Ph. # 800 835-4429)
•Gas Line Equipment (shutoff valve, pipe, etc.)
•Electrical Equipment (min. 18 gauge, grounded line)

8Installation (for qualified installers only)
Travis Industries 4050114 100-01149
8
Installation Overview
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
Non-combustible facing
(see the section "Facing
Requirements")
See the section "Acceptable
Vent Lengths"
See the section "Horizontal Termination
Requirements"
See the section
"Gas Line Installation"
See the section
"Electrical Connection"
See the section
"Mantel Requirements"
Insulation must not fill the 1"
clearance around the back and sides
of the fireplace.
See the section "Fireplace
Placement Requirements"
3-1/2" Min.
See the section
"Vent Requirements"
See the section "Minimum
Framing Dimensions"
See the section
"Hearth Requirements"
Drywall
Nail
Down
Plate
See "Power Heat
Vent" in the optional
equipment section.
This grommet and hole is for
thermostat wire (on both sides)
Recommended Installation Procedure
1 Frame the opening for the fireplace. Make sure to allow for vent installation and the type of installation (corner
or flat wall).
2 Insert the fireplace into the framing. Slide it back until the firebox front face is flush with the framing members.
Verify all clearances at this point.
3 Secure the fireplace to the floor by screwing or nailing through the nail-down plates (found on both sides and
back of the fireplace).
4 Complete the gas line installation.
5 Complete the electrical hook-up.
6 Complete the vent installation.
7 Install the hearth (if applicable).
8 Install the facing.
9 Install the mantel (if applicable).

Installation (for qualified installers only) 9
Travis Industries 4050114 100-01149
Fireplace Placement Requirements
Minimum Framing Dimensions
A 1" clearance is required along the sides and back of the fireplace. The 1" stand-offs on the sides and 10-
1/2" stand-offs on the top of the fireplace are designed to separate the fireplace from the framing members.
These stand-offs may contact the framing members but no material may be placed between the stand-offs
AAAAA
AAAAA
AAAAA
A
A
AAAAA
AAAAA
AAAAA
A
A
AA
AA
A
A
A
A
AA
AA
AA
A
AA
AA
AA
A
Gas line (3/8" M.P.T. or 1/2"
F.P.T.) should be routed 6-1/2"
behind the framing opening
and 2-3/8" above the base of
the fireplace (see "Gas Line
Connection" for details).
52"
24-3/8"
50-3/4"
Route the electrical line to a position
at the right rear of the fireplace.
If using a remote
control or thermostat,
route the wire to a
location near the gas
line (include an extra 3'
length for hookup).
NOTE: if venting directly to the rear,
make sure there is a min. 12" space
centered behind the fireplace.
NOTE: If using the power heat vent,
allow for the duct passage when
framing the enclosure.
Required Firestop (included with
the fireplace)
3" Clearance Min. (after firestop)
Minimum 65-1/2" above the
base of the fireplace (includes
18" min. rise before elbow -
see the section "Horizontal
Termination Requirements")
5-1/2" Clearance Min.
(before firestop)
1" Clearance min. to the sides
and below the vent (before or
after firestop).
The fireplace enclosure
must not be less than
75" above the base of
the fireplace.
75" Min.
•Fireplace must be installed on a level surface capable of supporting the fireplace and vent
•Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)
•Due to the high temperature of the fireplace, it should be located out of traffic and away from furniture and
draperies.
This heater may be placed in a bedroom. Please be aware of the large amount of heat this appliance produces
when determining a location.

10 Installation (for qualified installers only)
Travis Industries 4050114 100-01149
Clearances
•When installed, walls in front of the fireplace must be a minimum 3-1/2" to the side of the faceplate.
•Due to the high temperature, the heater should be located out of traffic and away from furniture and draperies.
•Fireplace must be placed so the vents below and above the glass do not become blocked
Vertical Standoff
•The vertical standoff above the fireplace must be erected prior to installation. See the illustration below for
instructions.
The vertical standoff is
shipped swiveled down.
Rotate the standoff
upwards into place.
1/4" Nutdriver
Secure the standoff
with the six screws. These lifting
handles may be
removed once
the fireplace is
in place.
7/16" Wrench
Nail or screw the
fireplace to the
floor through the
holes on these
brackets.

Installation (for qualified installers only) 11
Travis Industries 4050114 100-01149
Corner Installations
A typical 45°installation uses the minimum framing dimensions shown in the illustration below (NOTE: all
clearances still apply).
AAA
AAA
AAA
AAA
AAA
A
A
A
A
A
A
A
A
A
A
AAAAAAAAAAA
Approx. 16"
23-1/8" 1" Standoffs
19-5/8"
19-1/2"
Min. 1" Clearance
60-3/8"
Raised Fireplaces
•The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace
(approximately 300 Lbs.) and vent.
•The fireplace may not be raised so as to place the ceiling within 75" of the base of the fireplace.
•The fireplace may not be raised so as to reduce the fireplace enclosure to less than 75”.
Raised fireplace Raised fireplace with
raised hearth.
Raised
Platform
Raised Hearth
Hearth
Raised
Platform
6-1/4"
6-1/4"

12 Installation (for qualified installers only)
Travis Industries 4050114 100-01149
Gas Line Requirements
!The gas line must be installed in accordance with all local codes, if any; if not, follow ANSI 223.1 and the
requirements listed below.
!The fireplace and gas control valve must be disconnected from the gas supply piping during any pressure
testing of that system at test pressures in excess of 1/2 psig. For pressures under 1/2 psig, isolate the gas
supply piping by closing the manual shutoff valve.
!Leak test all gas line joints and the gas control valve prior to and after starting the fireplace.
Fuel
•This fireplace is designed either for natural gas or for propane (but not for both). Check the sticker on the top
of the gas control valve to make sure the correct fuel is used.
Gas Line Connection
•A manual shutoff valve is required for installation (within 3’of the heater or inside the fireplace).
T-Handle gas cocks are required in Massachusetts in compliance with code 248CMR.
Gas Control Valve
3/8" M.P.T to 1/2" O.D. Fitting
(Factory installed)
The 1" diameter access hole is located 2-3/8" above the base of the fireplace. Cut
an "X" in the gasket covering the inlet and insert the gas line through the gasket.
If the gas line is routed from the
right side, bend the flex tube 180°.
10" Flex Tube
(shipped with the fireplace - min. bending radius is 3/4")
A shutoff valve may be
placed within the fireplace
The included
fitting accepts a
3/8" M.P.T. or
1/2" F.P.T.
-- OR --
-- OR --
18-1/2"
6-1/2" 6-3/4"
The modulating remote shield may
be removed to ease installation.
Gas Inlet Pressure: Standard Input Pressure
Natural Gas 7" W.C. (1.74 kPA)
Propane 13" W.C. (2.73 kPA)
•If the pressure is not sufficient, make sure the piping used is large enough, the supply regulator is adequately
adjusted, and the total gas load for the residence does not exceed the amount supplied.
•The supply regulator (the regulator that attaches directly to the residence inlet or to the propane tank) should
supply gas at the suggested input pressure listed above. Contact the local gas supplier if the regulator is at an
improper pressure.

Installation (for qualified installers only) 13
Travis Industries 4050114 100-01149
Electrical Connection
!Make sure the household breaker is shut off prior to working on any electrical lines.
!The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence
of local codes, with the National Electrical Code, or ANSI NFPA.
•The electrical line must be 14 gauge, and supply 120 Volts at 60 Hz (2 Amps)
1Follow the directions below to connect power to the fireplace.
6-1/4"
ab
Insert the sheathed cable from the power source through
this cable clamp. Once the wires are attached, tighten
the clamp to secure the cable.
Replace
the cover
removed
in step "a".
Attach the common (white), ground (exposed or green) wires, and hot
(black) wires from the power source to the electrical connector (included
with the fireplace). Then attach the connector to the fireplace.
c
d
Standard
Screwdriver
Remove the cover from the
fireplace junction box.
1/4" Nutdriver
Electrical Connector
(shipped in the fireplace
behind the cover plate)
WARNING: Make sure power is
off from the power lead before
conducting any wiring.
NOTE:
If using the power heat duct, you may wish to route the
wiring for it at this point. See the instructions under
"Optional Equipment".

14 Installation (for qualified installers only)
Travis Industries 4050114 100-01149
Vent Requirements
!The vent must maintain the required clearance to combustible materials to prevent a fire (see “Clearances”
below). Do not fill air spaces with insulation.
!The gas appliance and vent system must be vented directly to the outside of the building, and never be
attached to a chimney serving a separate solid fuel or gas-burning appliance. Each direct vent gas appliance
must use it's own separate vent system.
Altitude Considerations
This heater has been tested at altitudes ranging from sea level to 8,000 feet (2,400 M). In this testing we have found that
the heater, with its standard orifice, burns correctly with just an air shutter adjustment.
!Failure to adjust the air shutter properly may lead to improper combustion which can create a safety hazard. Consult your
dealer or installer if you suspect an improperly adjusted air shutter.
Clearances
Horizontal Runs
AAA
AAA
AAA
Vertical Sections
Min. 3" Clearance Above 45°
Sloping Vent after first firestop
(5-1/2" before first firestop)
AAAAAA
Min. 1" Clearance to the
Sides & Below the Vent
(before or after the firestop)
A
A
A
A
A
A
A
A
A
A
A
AA
AA
AA
AAA
The Travis firestop is required
(part # 93006094) when passing
through any wall.
Min. 5-1/2" Clearance
Above the Vent
(before first firestop)
Min. 3" Clearance
Above the Vent
(after first firestop)
AAA
AAA
AAAAAAA
A
A
A
A
A
A
A
A
Min. 1" Clearance to the
Sides & Below the Vent
(before or after the firestop)
A
Min. 75"
(from base of fireplace)
Min. 18" rise before
first elbow.
Min. 75"
(from base
of fireplace)
Use the Simpson ceiling
firestop (#1263)
whenever passing
through a ceiling (or
enclosure and at every
floor penetration.
Part Numbers for 8”Diameter Vent
•Use 8”diameter Model GS Direct Vent manufactured by Simpson Dura-Vent
only. Follow the installation
instructions included with the vent. For the nearest Simpson Dura-Vent supplier, call [phone]. Vent
part numbers and descriptions are listed below.
Straight Lengths
1208B 6" Pipe Length, Black
1207B 9" Pipe Length, Black
1206B 12" Pipe Length, Black
1204B 24" Pipe Length, Black
1203B 36" Pipe Length, Black
1202B 48" Pipe Length, Black
1211B 11”to 14-5/8" Adjustable, Black
Terminations
1284 Horizontal Square Termination
1285 Hor. High Wind Termination
1250 Vinyl Siding Stand-off
1291 Travis Vertical Termination
Elbows
1245B 45°Elbow, Black
1290B 90°Elbow, Black
Penetration, Support
93006094 Travis Firestop
1241 Cathedral Ceiling Support Box
1288 Wall Strap
1263 Ceiling Firestop

Installation (for qualified installers only) 15
Travis Industries 4050114 100-01149
Vent Installation
•In addition to the requirements below, follow the requirements provided with the vent.
Vertical Termination
(part # 1291)
Use a roof flashing and storm collar
whenever passing through the roof
Vertical Vent
Requirements
Horizontal Vent
Requirements
Minimum framing
for fire stop
Min. 1" clearance from
vertical sections to
combustible surfaces.
10"
by
10"
Use the Simpson ceiling firestop (#1263) whenever
passing through a ceiling (or enclosure and at every
floor penetration.
Combustible
Framing
Use the Travis firestop (part # 93006094) when passing
through a wall. NOTE: make sure the firestop is postitioned
correctly so the 3" clearance is allowed above the vent.
3" Min.
1" Min.
1" Min. Combustible
Surfaces
Minimum framing
for fire stop
Minimum
12" tall
Minimum
10" wide
•Slide the vent sections together and turn 1/4 turn until the sections lock in
place.
•Screws are not required to secure the vent. However, three screws may be
used to secure vent sections together if desired.
•High temperature sealant is recommended at the appliance starter section
connection (use high-temperature silicone or Mill-Pac®).
•If disassembly is required, at time of re-assembly check to see if the vent
creates a tight fit. If it does not, apply high temperature sealant to the joints of
the affected sections.
•Horizontal sections require a 1/4" rise every 12" of travel
•Horizontal sections require non-combustible support every three feet (e.g.: plumbing tape)

16 Installation (for qualified installers only)
Travis Industries 4050114 100-01149
Approved Vent Configurations
Restrictor Position
•A vent restrictor is built into the appliance to adjust the flow rate of exhaust gases. This ensures proper
combustion for all vent configurations. Depending upon the vent configuration, you may be required to adjust
the restrictor position. The charts for acceptable vent configurations detail the correct vent restrictor position.
With the face removed and
the fireplace cool, reach
above the firebox.
To Adjust the Restrictor:
To Access the Restrictor:
1
2
Determine the correct restrictor position (see the charts under
"Approved Vent Configurations" - the factory position is #1).
Lift up the adjustment plate and move it so the correct notch
falls into the slot on the adjustment bracket.
This restrictor is in position 1
(factory setting).
This restrictor is in
position 6.
Adjustment
Bracket To adjust, lift up on the
adjustment plate and push it
back.
WARNING: Use a glove to protect
your hand from burns.
Adjustment
Plate
# 7 # 2
etc.
Elbows
•See the vent
configurations for
details on how
many elbows may
be used and in
what manner.
Measuring Vent
Lengths
6-1/4"
NOTE:
All measurements
are for 8" diameter
vent.
Vent
Horizontal
Run
Vent
Height 43-1/8"
10-3/4" wide with
1-3/4" to
3-3/8" of overlap
Starter
Section
12-3/8"
3-1/2"
Side
View
1-3/4"
Vent Length
(2', 3', etc.)
NOTE:
Vent sections overlap
each other by 1-3/4"
3-1/2"
8"

Installation (for qualified installers only) 17
Travis Industries 4050114 100-01149
Vertical Terminations with 0, 2, or 4 45° Offsets
Offset Length Hor. Offset Vert. Rise
None 5" 1'
1' Section 1' 1' 7"
2' Section 1' 9" 2' 4"
3' Section 2' 5" 3'
4' Section 3' 2" 3' 8"
Offset
Length
Horizontal
Offset
Vertical
Rise
•The termination must fall within the shaded area shown in the chart. Use the indicated restrictor position.
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAAAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
5 feet
10 feet
(min.)
15 feet
20 feet
25 feet
30 feet
0 feet
35 feet
0 feet
5 feet
6' (max)
5 feet
0 feet
0 feet
5 feet
6' (max)
10 feet
(min.)
15 feet
20 feet
25 feet
30 feet
35 feet
Four 45°Offsets
5 feet
10 feet
15 feet
20 feet
25 feet
30 feet
0 feet
40' (max)
0 feet
5 feet
5 feet
0 feet
0 feet
Restrictor
Position # 5
Restrictor
Position # 6
10 feet
15 feet
20 feet
30 feet
Zero or Two 45°Offsets
5 feet
12'
(max)
NOTE:
Restrictor positions are
based upon lab tests. The
ideal restrictor position may
vary slightly, especially when
the termination is near the
demarkation line.
25 feet
10 feet
12'
(max)
10 feet
Restrictor
Position # 5
Restrictor
Position # 6
35 feet 35 feet
40' (max) 40' (max) 40' (max)

18 Installation (for qualified installers only)
Travis Industries 4050114 100-01149
18
Horizontal Terminations with One Vertical Elbow
The termination must fall within the shaded area shown in the chart. Use the indicated restrictor position.
NOTE: If you are installing this fireplace with a minimum of vent rise, and are experiencing intermittent pilot
outages, you may need to install a pilot shield (SKU 250-00028). Contact your dealer for information.
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
NOTE:
• One horizontal elbow (45° or 90°) is allowed. The
horizontal vent length is calculated by adding the length
before and after the elbow (H1 + H2 = horizontal vent
length).
• Horizontal sections require a 1/4" rise every 12" of travel.
H1
Horizontal Elbow
(45° or 90°)
Vertical Elbow
H2
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAA
5 feet
0 feet
0 feet
25' (max)
5 feet
0 feet
25' (max)
Restrictor
Position #5
20' (max) 20' (max)
5 feet
10 feet
5 feet
10 feet
0 feet
15 feet
20 feet
10 feet
15 feet
15 feet
20 feet
10 feet
15 feet
NOTE:
Restrictor positions
are based upon lab
tests. The ideal
restrictor position may
vary slightly.
Min. 18" Rise Before First Elbow
Restrictor
Position #1

Installation (for qualified installers only) 19
Travis Industries 4050114 100-01149
Horizontal Terminations with Three Vertical Elbows
The termination must fall within the shaded area shown in the chart. Use the indicated restrictor position.
NOTE:
•A total of three elbows must be used.
•No horizontal elbows may be used (a horizontal elbow is defined
as an elbow that directs the vent from a horizontal direction to
another horizontal direction).
•Two 45°elbows may be substituted for two of the 90°elbows.
•Horizontal sections require a 1/4" rise every 12" of travel.
•The maximum vertical height is 19'.
•The maximum horizontal length is 20'.
Horizontal Elbows are
NOT ALLOWED
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAA
5 feet
0 feet
0 feet
5 feet
0 feet
19' (max) 19' (max)
5 feet
10 feet
5 feet
10 feet
0 feet
15 feet
20' (max)
10 feet
15 feet
15 feet
20' (max)
10 feet
15 feet
Min. 24" Rise
Before First Elbow
NOTE:
Restrictor positions are based upon
lab tests. The ideal restrictor position
may vary slightly.
Restrictor
Position #1
Restrictor
Position #5

20 Installation (for qualified installers only)
Travis Industries 4050114 100-01149
Vertical Terminations with Two Vertical 90° Elbows
The termination must fall within the shaded area shown in the chart. Use the indicated restrictor position.
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
5 feet
10 feet
(min.)
15 feet
20 feet
25 feet
30 feet
0 feet
40' (max)
5 feet
10 feet
15 feet
0 feet
5 feet
10 feet
15 feet
20'(max)
15 feet
20 feet
25 feet
30 feet
0 feet
0 feet
NOTE:
Horizontal sections require a
1/4" rise every 12" of travel.
10 feet
(min.)
40' (max)
20'(max)
Restrictor
Position # 6
NOTE:
Restrictor positions
are based upon
lab tests. The
ideal restrictor
position may vary
slightly, especially
when the
termination is near
a demarkation line.
5 feet
Restrictor
Position # 5
35 feet 35 feet
NOTE:
•One horizontal elbow is allowed.
It may be a 45°or 90°elbow.
H1
This is considered a
vertical elbow
Horizontal length is calculated by
adding both lengths of horizontal run
(Horizontal Length = H1 + H2).
H1
H2 This is considered a
vertical elbow
This is considered a horizontal elbow because it
is between two horizontal sections.