FISCHER MMS User manual

MMS®Inspection DPM
Gage variant High
User Manual
Gage for measurement
and determination of
ambient climatic variables
as drew point, relative
humidity, air and surface
temperature

MMS®Inspection DPM (H)
Gage variant High (606-033)
Gage for measurement and determination of ambient climatic variables as drew
point, relative humidity, air and surface temperature
On our home page www.helmut-fischer.com you will find the addresses of our sole
agencies and subsidiary companies around the globe.
© 2022 by Helmut Fischer GmbH Institut für Elektronik und Messtechnik, Germany.
This document is protected by copyright. All rights reserved. This document may not
be reproduced by any means (print, photocopy, microfilm or any other method) in full
or in part, or processed, multiplied or distributed to third parties by electronic means
without the written consent of Helmut Fischer GmbH Institut für Elektronik und Mess-
technik.
Subject to correction and technical changes.
MMS®is a registered trade mark of the Helmut Fischer GmbH Institut für Elektronik
und Messtechnik in Germany and other countries.
Microsoft and MSExcel are registered trade marks of the Microsoft Corporation, USA.
Bluetooth®is a registered trade mark of the Bluetooth SIG, USA.
Note: Designations not marked with ® or ™ may also be protected by law.
Document no.: 1000664
Issue date: 2022-09 (for firmware 2.0.1)
Manufacturer
Helmut Fischer GmbH Phone: [phone] - 0
Institut für Elektronik und Messtechnik Fax: [phone] - 710
Industriestraße 21 www.helmut-fischer.com
D-71069 Sindelfingen [email protected]
Quality Assurance System of the Helmut Fischer GmbH Institut für Elektronik und
Messtechnik
DIN EN ISO/IEC 17025 Calibration lab accredited for certified mass per unit
area standards
DIN EN ISO 9001:2015 Management system certified by Swiss Association
for Quality and Management Systems (SQS)

iMMS®Inspection DPM High
Table of Content
1 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Environmental conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Safety of the electrical equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Measurement view (example). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Gage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Menus - function overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5 Gage concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1 Switching on the gage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2 Switching off the gage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3 Initial set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5 Settings for measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.1 Creating a new batch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.2 Opening a batch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.3 Limit monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.4 Alarm monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.5 Log function (Auto Logging). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6 Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.1 Limitation of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.2 Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.3 Measurement - Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.4 Correctly holding the gage during the measurement . . . . . . . . . . . 30
7Evaluation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.1 Call up statistical characteristic variables . . . . . . . . . . . . . . . . . . . . 33
7.2 Run charts of climatic variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8 Data transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.1 USB data transfer to an Excel spreadsheet via PC-Datex. . . . . . . . 37
8.2 USB data transfer to the Fischer DataCenter . . . . . . . . . . . . . . . . . . 42
8.3 USB data transfer to a CAQ system . . . . . . . . . . . . . . . . . . . . . . . . . . 47
8.4 Bluetooth data transfer to an Excel file via PC-Datex . . . . . . . . . . . 50
8.5 Bluetooth data transfer to a CAQ system . . . . . . . . . . . . . . . . . . . . . 55
8.6 Settings for the Bluetooth-gage pairing . . . . . . . . . . . . . . . . . . . . . . 58

ii MMS®Inspection DPM High
Table of Content
9Managingbatchfiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9.1 Assigning/changing batch name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
9.2 Deleting a batch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
9.3 View batch infos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
9.4 Change the unit of measurement for temperature. . . . . . . . . . . . . . 64
10 Gage settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
10.1 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
10.2 Display settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
10.3 Enabling/disabling the visual signals . . . . . . . . . . . . . . . . . . . . . . . . . 70
10.4 Visual signal intensity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
10.5 Energy Savings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
10.6 Date & time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
10.7 Used battery type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
10.8 Default setting – unit of measurement . . . . . . . . . . . . . . . . . . . . . . . . 75
11 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
11.1 Changing the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
11.2 Gage cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
11.3 Test measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
11.4 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
12 Malfunctions – What should you do? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
13 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
13.1 Glossary – Display symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
13.2 Glossary – Display texts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
14 Gage information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
15 E-Label, regulatory information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
15.1 Call up e-Label pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
15.2 Directives/regulatory information on wireless data
transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
15.3 USA, FCC (Federal Communications Commission) . . . . . . . . . . . . . 101
15.4 Canada, ISED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
15.5 Europe, CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
15.6 China, SRRC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
15.7 Japan, MIC (Ministry of Internal Affairs and Communications) . . 105
15.8 India, MCITT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
15.9 Brazil, ANATEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
15.10 Mexico, IFT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
EU - Declaration of Conformity

Safety Information
1
MMS®Inspection DPM High
1 Safety Information
If you use the gage as intended and observe the safety information, it will not
present any danger.
Read and follow the instructions in this operator’s manual and observe the
safety information. Also observe generally applicable safety and accident pre-
vention regulations.
1.1 Intended use
The gage is intended solely for measurement and determination of ambient cli-
matic variables as dew point, relative humidity, air and surface temperatures.
Only accessories approved or recommended by the manufacturer may be con-
nected to the gage.
Any use beyond this is not the intended use. The risk of damage resulting from
this is borne solely by the user!
1.2 Environmental conditions
Elevated temperature
When exposed to sunshine, the areas behind glass windows (e.g. in an automo-
bile) can easily reach temperatures in excess of +50 °C (122 °F). This can cause
damage to the gage.
►Do not keep or store the gage and accessories behind glass panes, or
near to heat sources such as radiators etc.!
Destruction of the gage by condensation
When the gage is moved from a cold environment to a warm environment,
condensation can form inside the gage and damage its electronics. Such
extreme temperature fluctuations occur in winter, for example, between
outdoor(0°C/32°F)androomtemperature(+22°C/71.6°F).
►Allow the gage some time to acclimatize to the ambient temperature
before you start the measurement.

Safety Information
2MMS®Inspection DPM High
Potentially explosive environments
The gage and accessories are no t suitable for use in potentially explosive
environments.
►Operate the gage and accessories only outside of potentially explosive
areas!
1.3 Safety of the electrical equipment
USB cable
Damaged USB cable
Kinking or pinching the USB cable can result in a broken wire. Data transmis-
sion is then no longer possible.
►Connect only an undamaged USB cable with a max. length of 3 m
(118.1 inches) to the gage.
►Always coil up the USB cable for storage.
Batteries/rechargeable batteries
Use the following alkaline or lithium battery type: Mignon, 1.5 V, LR6 ·AA.
or
 Use the following NiMH rechargeable battery type: Mignon, 1.2 V, HR6 · AA.
Damaged batteries
The use of defective batteries or the wrong type of battery causes damage to
the gage! Leaking batteries destroy the gage's electronics!
►Use only undamaged batteries!
►Use only the battery types mentioned above!
►Use only leak-proof batteries!
►Store the gage without batteries when not in use for a longer period of
time!
RED (2014/35/EU, Radio Equipment Directive)
The gages of the MMS Inspection Series comply with the regulations concern-
ing of placing radio equipment on the market (2014/35/EU, Radio Equipment
Directive). Mains operation with the AC power supply or via PC is possible, but
not recommended. The guaranteed RED characteristics apply exclusively to
battery operation!

Safety Information
3
MMS®Inspection DPM High
Servicing and repairs
Modifications, repairs, as well as maintenance and service work on the gage
and accessories may be carried out only by service personnel authorized by the
manufacturer.
Exception: Changing the batteries/rechargeable batteries.

Description
4MMS®Inspection DPM High
2Description
The gage model MMS Inspection DPM
is for continuously measuring air
temperature and humidity to deter-
mine the dew point. To measure the
surface temperature continuously,
you can connect a magnetic tempera-
ture probe to the gage.
This operator's manual describes the
following gage version in the MMS In-
spection DPM series:
High variant
USB and Bluetooth interfaces,
data storage for 250 000 values
in up to 2500 batches. You can
log the climate values over a
prolonged period and emit a vi-
sual warning if specified limits
are exceeded.
Additional information can be found in
the data sheet, page 9
2.1 Measurement view
(example)
1Batchname
2 Permanently measured and
calculated climatic values with
measurement units
3 Number of storages of all
climatic values
4 Key assignment line (example:
symbol for delete function,
symbol for calling the run
charts and statistics of all
climatic variables, symbol for
Hold function)
5 Status display; icons indicate,
e.g., active autom. gage switch-
off (clock), battery charge
status or the active connection
of Bluetooth or USB
6 Information area; A: alarm
function for the variable is
active; : trend display
A list of all display symbols and texts
can be found starting on page 90.
1
2
3
4
Batch 003
RH 34.9 %A
Ta 26.1 °C
Ts 27.2 °C
Td 10.3 °C
Ts-Td 16.9 °C A
n = 3
Example of the measurement
view with trend display ( )
and active alarm function (A)
/
5
6
/

Description
5
MMS®Inspection DPM High
2.2 Gage
Front of gage Rear of gage
1 Eyelets for a carrying strap
2 Signal lamp for displaying the alarm signal for limit violations (alarm
function)
3Display
4 Keys, On/off key, for description see page 6
5 Type K connection below the cover for connecting a type K (magnetic)
temperature probe. When a temperature probe is connected, the function
of the gage surface temperature probe (6) is automatically switched off.
6 Gage surface temperature probe (protective cap in scope of supply)
7USBport
8 Battery compartment cover
9 Air temperature and humidity probes protected by the housing grille
Gage dimensions can be found in the data sheet, page 12
1
3
4
5
6
2
7
8
9

Description
6MMS®Inspection DPM High
2.3 Keys
There are 4 keys for operating the gage.
The bottom line of the display always shows the functions of the 4 keys (see il-
lustration below). The assignment depends on the open page.
The function shown on the display is assigned to the key directly underneath (example).
The key has two functions:
switches the gage on and off when the key is held for at least 1 s.
opens/activates the function shown in the bottom line of the display.
The key has two functions:
moves the cursor/mark down when is shown in the bottom line of
the display.
opens the main menu when is not shown in the bottom line of the
display.
A description of the remaining key symbols can be found starting on page 91
OK

Description
7
MMS®Inspection DPM High
2.4 Menus - function overview
Main menu
Statistics > Display the statistics for the open batch
Batch
Modify >
Settings and en-
tries for the
open batch
MEASURE > Go to the Measurement view
Tolerance Limits > Activate/Deactivate limit monitoring
and set the specification limits
Alarm Settings Enable/Disable alarm function, limit
value settings
Auto Logging Enabling the auto log function (Log
function) and set the log interval
Batch Infos Information on the measurement and
batch settings
Temperature Units selection between °C and °F
Batches > New >
List of saved batches
(After a batch has been selected, it can be opened, renamed,
copied or deleted.)
Gage Settings > Language Select the display language
Display Settings > Brightness
Flip display
Indication Settings > Visual signal, luminosity
Data Transfer > USB
Bluetooth
Energy Savings > Automatic gage switch-off and display
dimming after a preset period of time
Date & Time > Date and time
Date and time format
More Settings > Preset the temperature unit
Battery type
Probe Settings > Test measurements
Regulatory Information about the country-specific
Radio certifications (E-Labels)
About > Information about firmware version
and measuring system as well as legal
information such as copyright

Description
8MMS®Inspection DPM High
2.5 Gage concept
In order to measure, a batch (file) must be created in the gage for measuring
application. In addition to the settings for the measurement, the climate values
and the statistical characteristic values are also stored in the batch file.
A description of the terms "measuring application" and "batch" can be found in
Chapter "Glossary".
The essential content of the batch files are shown schematically in the following
illustration:
Gage
Batch 001
(settings, readings, statistical characteristic variables)
Limit monitoring (setting per climatic variable)
Alarm function (visual signalization, setting per
climatic variable)
Log interval
Temperature measurement unit
Batch 002
(settings, readings, statistical characteristic variables)
Limit monitoring (setting per climatic variable)
Alarm function (visual signalization, setting per
climatic variable)
Log interval
Temperature measurement unit
Batch 003
(settings, readings, statistical characteristic variables)
Limit monitoring (setting per climatic variable)
Alarm function (visual signalization, setting per
climatic variable)
Log interval
Temperature measurement unit
different
measuring
applications
…

Data Sheet
MMS®Inspection DPM High
Monitoring climatic ambient conditions
Dew Point
Surface Temperature
Air Temperature
Relative Humidity
2.6 Technical Data
Easy and convenient
operation
Compact and robust case

MMS®Inspection DPM High
10
Description
The gage model MMS Inspection DPM High measures all relevant climatic variables such as rel-
ative humidity, air and surface temperature and determine dew point and the temperature dif-
ference between dew point and surface temperature from these variables. All these variables
can be logged continuously. The measuring device can also monitor all climatic variables and a
red signal light warns in case of limit violations.
Gage properties Ideal for onsite applications (outside and inside) due to the compact size, the light weight and
the robust and durable instrument design
All measurement sensors (humidity, air, surface temperature) are integrated in the gage, for
single-handed operation
Additional temperature sensor can be connected to the gage, e. g., sensor with magnetic
support for continuous measurement of surface temperature
IP65, dust-tight and water repellant and resistant
Intuitive operation of the menu navigation and graphic display
The measurement presentation flips automatically and thus allows optimum reading in dif-
ferent measuring positions
Different languages selectable
Continuous logging all climate variables
Application
Example Monitoring of the climate ambient conditions, which are required for surface varnishing
Gage type
High-end gage with large data memory for 250,000 values in 2500 batches, continuous logging of
the climate values over a longer period of time in a selectable recording interval between 1 to 99
minutes (Log function), optical warning signal when limit values are exceeded, USB and wireless in-
terfaces for data transfer
Metrological Standard Functions Measurement Tasks
Batch File containing all metrological function settings necessary for the measurement task as well as the
climatic values and evaluations
Tolerance limits Settable, upper and lower limit values for the variables relative humidity (RH), air tempera-
ture (Ta), surface temperature (Ts), dew point (Td) and Ts-Td;
The limits specify also the scaling of Y chart axis of the respective run charts
In case of limit violation, the reading is displayed in red
Monitoring alarm Settable alarm limit values for the variables relative humidity (RH), air temperature (Ta), sur-
face temperature (Ts), dew point (Td) and Ts-Td;
The optical alarm indicates a limit violation by a red flashing signal light
Log function Automatic data logging according to the given time interval, between 1 to 99 minutes
Hold function Freezing the present displayed values
Measurement displaying Permanent measurement acquisition and displaying
Reading storage manually by using the Hold function; you can store the readings shown in the frozen display
automatically according to the given time interval, by means of the Log function
Measurement units °C/°F selectable, %RH

MMS®Inspection DPM High
11
General Features
Factory Calibration Each individual gage is factory calibrated at several reference points with the greatest care to en-
sure the highest possible degree of trueness.
Measuring sensors The gage contains senors for measuring air temperature, surface temperature and relative humidi-
ty; specifications see page 5
Data memory The memory content is preserved even when there is no voltage supply; subsequent viewing of the
measured single readings and evaluations
Memory capacity of 250,000 readings in up to 2500 batches
Evaluation Statistics
Display of mean value, standard deviation, min/ max values, number of stored readings, range, co-
efficient of variation, date and time for each variable relative humidity (RH), air temperature (Ta),
surface temperature (Ts), dew point (Td) and Ts-Td
Graphic Presentation
Run-Chart, showing the progress of stored readings of each climatic variable; the scaling of Y chart
axis are specified by the set limits
Indication for monitoring alarm Limit violation: optical by red illuminated LED
Languages Many different display languages, beside German and English several other European and Asian
languages
Date & Time Setting of date and time
Setting of date and time format
Presetting for batches Each batch is created with a preset measurement temperature unit; you can change this measure-
ment unit at any time
Display Graphic display with automatic flipping measuring presentation view (disabeling) to read
measurement results in many different gage positions
Setting of brightness and contrast (definable for Office, Sunlight and Night)
Data transfer USB: Data transfer of individual measurements of all climatic variables to a PC
Data export into MSExcel via Add-In program PC-Datex; You can download the PC-Datex program
free of charge from Fischer-Download page, https://docs.helmut-fischer.com/st9
Data export into the evaluation, recording and archiving software Fischer DataCenter (from ver-
sion 2.6); You can download the Fischer DataCenter program free of charge from Fischer-Down-
load page, https://docs.helmut-fischer.com/st9
USB: Data transfer of individual measurements of all climatic variables to a CAQ system
Bluetooth: Data transfer of individual measurements of all climatic variables to a PC
Data export into MSExcel via PC-Datex software; You can download the PC-Datex program free of
charge from Fischer-Download page, https://docs.helmut-fischer.com/st9
Data export to software Fischer DataCenter is not possible.
Bluetooth: Data transfer of individual measurements of all climatic variables to a CAQ system
USB port 2.0 Type C
For connection to PC for data transfer, max. cable length: 3 m (118 inches)
For service purpose
Bluetooth Bluetooth module integrated in gage, Bluetooth 4.2
Frequency range: 2402 … 2480 MHz, max. output power: 6.13 dBm
Temperature connector Type K, to connect an external type K temperature sensor, e.g., magnetic surface temperature sen-
sor (606-036)

MMS®Inspection DPM High
12
Admissible climatic conditions during
storage and transport
Ambient temperature Relative Humidity
0 … +50 °C
(+32 … +122 °F)
5 … 85 %RH, at 25 °C (77 °F), non-condensing
Admissible climatic conditions during
operation
Ambient temperature Relative Humidity Altitude of location Pollution Degree
0 … +50 °C
(+32 … +122 °F)
5…85%RH,
at 25 °C (77 °F),
non-condensing
up to 2000 m
(6561.7 ft (US))
(above sea level)
3
Protection class (housing) IP65, measurements under water are not permissible
Weight (incl. batteries) about 259 g
Power supply 2 batteries: Mignon, Alkaline or Lithium, LR6 - AA, 1.5 V
2 rechargeable batteries: Mignon, NiMH, HR6 - AA
Battery life
Specifications valid for +20 °C (+68 °F) ambi-
ent temperature and Alkaline batteries used
> 8 h for continuous measuring, brightness set to sunlight and deactivated Bluetooth interface
Energy saving function To extend the battery life
automatic gage switch-off after preset time period without action (measurement, data
transmission, device operation)
automatic display dimming after preset time period
Dimensions
Gage
General Features
15 mm
(0.59 ")
18.3 mm (0.72 ")
29 mm
(1.14 ")
38 mm
(1.5 ")
73 mm (2.9 ")
45 mm
(1.8 ")
186 mm (7.3 ")
50 mm (2 ")

MMS®Inspection DPM High
13
Specifications of Sensors Air temperature (Ta) Surface temperature (Ts) relative Humidity (RH)
Measurement range -20 … +60 °C
(-4 … +140 °F)
-20…+80°C
(-4 … +176 °F)
0…100%RH
Trueness 20 … 50 °C: ± 0.1 °C
(68 …122°F:±0.18°F)
±0.5°C
(± 0.9 °F)
±2.5%RH
Resolution 0.01 °C (0.018 °F) 0.1 °C (0.18 °F) 0.01 %RH
External Magnetic Surface Temperature Sensor Type K (606-036) - Accessory
Sensor type K
Measurement range -40 … +200 °C (-40 …+392 °F)
Trueness ± 2 °C (± 3.60 °F)
Resolution 0.1 °C (0.18 °F)
Diameter of magnetic support 26 mm (1.02 ")
Scope of Supply
Gage; 2batteries; USB cable type C to type A (1 m(39.4 inches)); guideline Quickstart; lanyard;
manufacturer inspection certificate
Order Information MMS Inspection DPM
Gage Variant Order no. Interface Memory capacity Interval Log
function
Monitoring
alarm
High 606-033 USB + BT 250,000 readings in
2500 batches
selectable
1…99min
Accessory for
MMS Inspection DPM
Product Order no. Description
Surface temperature
sensor
606-036 Magnetic surface temperature sensor, type K,
self-adhesive on ferrous materials, cable length:
2 m (78.74 "), connection plug type K
Manufacturer inspec-
tion certificate
1003285
Lanyard 603-996 Carrying stripe for attaching the gage
Battery compartment
cover
287-776 Spare battery compartment cover for gage

MMS®Inspection DPM High
14

MMS®Inspection DPM High
15

MMS®Inspection DPM High
www.helmut-fischer.com
MMS®is a registered trade mark of the Helmut Fischer GmbH Institut für Elektronik und Messtechnik in Germany and other countries.
MSExcelTM is a registered trade mark of Microsoft Corporation, USA. Bluetooth®is a registered trade mark of the Bluetooth SIG, USA.
High 06092022