Fisher & Paykel CI302DTB User manual

NZ AU GB IE
590492A 03.13
CI302DTB, CI603DTB, CI604DTB,
CI754DTB & CI905DTB
models
INSTALLATION INSTRUCTIONS
Induction cooktop

3
WARNING!
Electrical shock hazard
Disconnect the appliance from the
mains electricity supply before carrying
out any work or maintenance on it.
Connection to a good earth wiring
system is essential and mandatory.
Alterations to the domestic wiring
system must only be made by a qualified
electrician.
Failure to follow this advice may result
in electrical shock or death.
WARNING!
Cut hazard
Take care - some panel edges are sharp.
Failure to use caution could result in
injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS!
Particular attention shall be given to the relevant
requirements regarding ventilation.
Read these instructions carefully before installing
this product.
Please make this information available to the
person installing the appliance as it could reduce
your installation costs.
This appliance is to be installed and serviced only
by an authorised person.
Installation must comply with your local building
and local electricity regulations.
The manufacturer accepts no responsibility for
the incorrect installation of appliances. Incorrect
installation may result in personal injury, damage
to property and may invalidate any warranty or
liability claims.
Do not modify this appliance.
Do not use or store flammable materials on or near
this appliance.
Packing elements (eg plastic bags, polystyrene
foam, staples, packing straps etc) and tools should
not be left around during and after installation,
especially if they are within easy reach of children,
as these may cause serious injuries.
SAFETY AND WARNINGS
1

4
SAFETY AND WARNINGS
1
Before you install the appliance,
please make sure that
a suitable disconnection switch is incorporated in
the permanent wiring, mounted and positioned
to comply with the local wiring rules and
regulations. A means of disconnection with at
least a 3 mm air gap contact separation in all
poles must be incorporated into the fixed wiring
in accordance with the wiring rules, unless the
local wiring rules allow for alternative means.
the benchtop is made of a heat resistant material.
the power supply cable is not accessible through
cupboard doors or drawers.
there is adequate flow of cool air from the
cabinetry to the base of the cooktop. You may
ventilate from adjacent cupboards, but ensure
that the available air supply will not be restricted.
the ventilation area must be at least two o 50mm
holes or of an equivalent area.
the isolating switch is easily accessible by the
customer.
you use heat-resistant and easy-to-clean finishes
(such as ceramic tiles) for the wall surfaces
surrounding the cooktop.
the cooktop will not be installed directly above a
dishwasher, fridge, freezer, washing machine or
clothes dryer, as the humidity may damage the
cooktop electronics.
if the cooktop is installed above an oven, the oven
has a built-in cooling fan.
the installation will comply with all clearance
requirements and applicable standards and
regulations.
you consult local building authorities and by-laws
if in doubt regarding installation.
When you install the appliance
We do not recommend you flush mount or seal
this appliance into the bench with silicone or
glue. Doing so will make future servicing difficult.
Fisher & Paykel will not be liable for any costs
associated with removing or replacing a sealed-in
appliance, nor for repairing any damage that may
be incurred by doing this.
Seal exposed bare edges of the cutout with an
oil-based paint or moisture-proof polyurethane to
prevent possible moisture creeping between the
cooktop trim and the benchtop.
Take extreme care not to chip, crack, or break the
top glass surfaces during installation. A heavy
metal tool or part accidentally dropped on the
glass could damage it.
If, after following the instructions given, correct
performance cannot be achieved, please contact
your nearest Fisher & Paykel Authorised Service
Centre, Customer Care, or contact us through our
local website listed at the end of this document.

5
PARTS SUPPLIED
2
Clamping brackets (4)
and screws (4)
CG302DTB only
Clamping brackets (2)
and screws (2)
Installing multiple products
Note: We recommend installing products in separate cutouts with a minimum distance of 5 mm between the glass edges.
If installing multiple products adjacent to each other within the same cutout, a separate joining strip kit is required for installation.
The kit is available from the nearest Fisher & Paykel Authorised Service Centre or our local website listed at the end of this document.
If installing different products adjacent to each other (eg a wok burner next to an induction cooktop), the minimum clearance measurements for the different products may vary. Always use the greater distance.
Foam tape (1)

6
A
D
B
E
C
G
F
H
I
4PRODUCT & CABINETRY DIMENSIONS
Product and cabinetry dimensions (mm)
CI302DTB CI603DTB CI604DTB CI754DTB CI905DTB
Aoverall height of product
(including terminal block below top of chassis) 54 54 54 54 54
Boverall width of product 300 600 600 750 900
Coverall depth of product 530 530 530 530 530
Dheight of chassis
(including terminal block below top of chassis) 49 49 49 49 49
Ewidth of chassis 254 546 546 716 852
Fdepth of chassis 478 478 478 478 482
Goverall width of cutout 265 560 560 725 870
Hoverall depth of cutout 490 490 490 490 494
Icorner radius of cutout max. 10 max. 10 max. 10 max. 10 max. 10
Note: Electrical connection is
made at the right rear
TOP TOP
REAR
FRONT
SIDE

7
BD
E
5CLEARANCE DIMENSIONS
Clearance dimensions (mm)
CI302DTB CI603DTB CI604DTB CI754DTB CI905DTB
Aminimum clearance from rear edge of cutout to nearest combustible surface 30 30 30 30 30
Bminimum clearance from glass surface to rangehood 650 650 650 650 650
Cminimum clearance from side edges of cutout to nearest combustible surface 30 30 30 25 25
Dminimum clearance from benchtop to overhead cabinet not directly above the cooktop 450 450 450 450 450
Eminimum clearance below top of benchtop to:
rear top of oven* installed below cooktop or cabinetry 65 65 65 65 65
* The oven installed below the cooktop MUST have a cooling fan.
FRONT
ISO
C
C
A
min. 75 mm
Alternatively
2x 50mm holes
in side wall
to allow adequate
cool air
min. 4 mm
min. 4 mm
Drawer or other obstruction
Oven with cooling fan
Ventilation gap
must be present
20 mm
Alternatively
2x 50mm holes
in side wall
to allow adequate
cool air
E
WARNING!
This cooktop requires
adequate supply of cool air
to fully function.
The base of the cooktop
must have direct
unrestricted ventilation to
the room where the
cooktop is installed. Follow
the requirements shown.

8
FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED)
6
A
D
B
E
C
F
G
G
K
L
HH
IJ
WARNING!
We do not recommend flush mounting and sealing as
servicing requires the cooktop to be removed from the
benchtop. The owner carries all risk for flush mounting
the cooktop. The owner must ensure the cooktop has
been cut out from the benchtop before servicing can
be carried out. Fisher & Paykel will not be liable for any
costs associated with removing or replacing a flush-
mounted and/or sealed-in product, nor for repairing
any damage that may be incurred by doing this.
Product and cabinetry dimensions (mm)
CI302DTB CI603DTB CI604DTB CI754DTB CI905DTB
Aoverall height of product
(including terminal block below top of chassis) 54 54 54 54 54
Boverall width of product 300 600 600 750 900
Coverall depth of product 530 530 530 530 530
Dheight of chassis
(including terminal block below top of chassis) 49 49 49 49 49
Ewidth of chassis 254 546 546 716 852
Fdepth of chassis 478 478 478 478 482
Goverall width of routered recess 305 605 605 755 905
G
I
width of cutout 265 560 560 725 870
Hoverall depth of routered recess 535 535 535 535 535
H
I
depth of cutout 490 490 490 490 494
Icorner radius of cutout max. 10 max. 10 max. 10 max. 10 max. 10
Jcorner radius of routered recess max. 2 max. 2 max. 2 max. 2 max. 2
Kheight of routered recess 55555
L
minimum clearance below top of benchtop to:
rear top of oven* installed below cooktop or cabinetry
thermal protection barrier
65
65
65
65
65
65
65
65
65
65
Note: Electrical connection is
made at the right rear
TOP TOP
REAR SIDE
FRONT

9
6
6a
6d
6b
6e
6c
6f
FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED)
ROUTER THE BENCHTOP TO THE
SPECIFIED DEPTH
APPLY SILICONE
FIT THE CLAMPING BRACKETS
WIPE OFF EXCESS SILICONE
MASK OFF THE AREA TO BE
SILICONED
IF REMOVING PRODUCT, CUT
AROUND THE SILICONE
5 mm
1
2
3
min. 150 OC rated
1
2
TO REMOVE PRODUCT
Ensure silicone does not leak underneath glass.
12-40mm 40mm+
view from below
No. of brackets and slot positions depends on model
Fit a minimum of 2 brackets on opposing sides

10
78
10
DISCARD PACKAGING PLACE COOKTOP UPSIDE DOWN
LOWER GENTLY INTO THE CUTOUT
Recycle responsibly
Important!
To avoid damage to the glass, ensure there is a protective cover underneath it.
9APPLY ADHESIVE FOAM TAPE AROUND GLASS EDGE
Foam Tape
Adhesive side
Ensure edge of tape
lines up with outer
edge of cooktop
1 Apply the foam seal around the glass
overhang, 5 mm in from the edge of
the glass, with the adhesive side facing
down to form a continuous seal around
the cooktop.
2 Using a sharp cutter or trimmer knife,
trim the excess sealing material around
the edge of the cooktop. Take care not
to damage the benchtop.