Fisher & Paykel CT2802 Series Mounting instructions

Ceramic glass cooktops
Installation instructions
and User guide
NZ AU
CT2802, CT560C, CT5602F and CT6551S models

1
Contents
Safety and warnings 2
Installation instructions 6
Introduction 8
Using your cooktop 10
Cookware and cooking tips 12
Care and cleaning 13
Frequently asked questions 14
Warranty and service 15
Important!
SAVE THESE INSTRUCTIONS
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please go to our website www.fisherpaykel.com or
contact your local Fisher & Paykel dealer.

2
Important safety precautions
Installation
Read these instructions carefully before installing or using this product.
Please make this information available to the person responsible for installing the product as it
could reduce your installation costs.
This appliance must be installed in accordance with these installation instructions.
This appliance is to be installed only by an authorised person.
Incorrect installation, for which the manufacturer accepts no responsibility, may cause personal
injury or damage.
Always disconnect the cooktop from mains power supply before carrying out any maintenance or
repairs.
WARNING!
Cut Hazard
Beware of sharp edges when handling appliances.
Failure to use caution could result in injury or cuts.
WARNING!
Electrical Shock Hazard
Before carrying out any work on the electrical section of the appliance, it must
be disconnected from the mains electricity supply.
Connection to a good earth wiring system is absolutely essential.
Failure to follow this advice may result in death or electrical shock.
Safety and warnings

3
This product should not be sealed into the bench with silicone or glue. Doing so will make future
servicing difficult. Fisher & Paykel will not be liable for costs associated with releasing such a
product, nor for repairing damage that may be incurred in doing this.
When this product is installed it shall not be used as a space heater, especially if installed in
marine craft or caravans.
No combustible material or products should be placed on this product at any time.
Before you install the appliance, ensure that
the benchtop is square and level and no structural members interfere with space requirements.
there is a minimum of 60 mm between the cutout and the rear or side wall.
if the cutout is less than 100 mm from the wall, some form of protection against heat is used, such
as ceramic tiles.
if the appliance is a CT2802 model, the power supply cable is rated for use at 100
O
C.
a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned
to comply with local wiring rules and regulations. A means of disconnection with at least a 3 mm
air gap contact separation in all poles must be incorporated into the fixed wiring in accordance
with the wiring rules, unless the local wiring rules allow for the following variation of these
requirements: A means of disconnection from the supply having an air gap separation in all
active (phase) conductors must be incorporated into the fixed wiring.
the interconnection cord between the cooktop and the oven or control box will not be accessible
via cupboard doors after installation. This applies to any extension cord as well, even if they are
double-insulated.
you consult local building authorities and by-laws if in doubt regarding installation.
the appliance is rated 5.9 kW at 220-240 V (CT560C,CT5602F,CT6551S models) or 3.0 kW at
220-240V (CT2802 models).
When you install the appliance, ensure that you comply with the following requirements:
If prolonged use is anticipated, or the cooktop is mounted above a drawer space, a thermal
protection barrier between is recommended AND
Where the base of this product is accessible after installation, a thermal protection barrier MUST
be installed to prevent contact.
If a thermal protection barrier is installed below the cooktop, this barrier must be made of heat
resistant material capable of withstanding sustained exposure to temperatures up to 70
o
C,
be at least 30 mm and no greater than 75 mm below the base of the cooktop and have FOUR
ventilation holes or TWO similiar holes for CT2802 models (min 50 mm – max 70 mm diameter,
see Fig. 1 for details). These ventilation holes must be open to free air.
We recommend that the thermal protection barrier be removable, so that the cooktop can be
easily secured with the supplied clamps.
Use easy-to-clean finishes for the wall surfaces surrounding the cooktop, so that cooking fume
staining resulting from using the cooktop is easy to remove.
Safety and warnings

4Safety and warnings
WARNING!
Hot Surface Hazard
During use, accessible parts of this appliance will become hot enough to cause
burns.
Avoid body or clothing contact with the ceramic glass until it is cool.
Keep children away.
Handles of saucepans may be hot to touch. Check saucepan handles do not
overhang other elements that are on. Keep handles out of reach of children.
Failure to do so may result in serious injury.
WARNING!
Electrical Shock Hazard
Do not attempt to use this appliance if the ceramic glass surface is cracked. If
the surface becomes cracked, switch the appliance and the power supply o
immediately.
Switch the cooktop o at the wall before cleaning or maintenance.
Failure to do so may result in death or electrical shock
WARNING!
Cut Hazard
When the safety cover is retracted, the blade in the scraper is razor-sharp. Use
with extreme care and always store safely and out of reach of children.
Failure to use caution could result in injury or cuts.

5
Important safety precautions
Operation
Household appliances are not intended to be played with by children.
Children or persons with a disability that may limit their ability to use the appliance should
have a competent person to instruct them in its use. This person should be satisfied that
they can use the appliance without danger to themselves or their surroundings.
This appliance shall not be used as a space heater, especially if installed in marine craft or
caravans.
If the power supply cable is damaged, it must only be replaced by an authorised person.
This appliance should be connected to a circuit which incorporates an isolating switch
providing full disconnection from the power supply.
Do not use a steam cleaner to clean your cooktop.
Do not stand or place heavy objects on this appliance.
Do not use pans with jagged edges or drag pans across the ceramic glass surface as this can
scratch the glass.
Do not use scourers or any other harsh/abrasive cleaning agents to clean your cooktop, as
these can scratch the ceramic glass.
Safety and warnings

6Installation instructions
Fig. 1 Thermal protection barrier - Dimensions and locations of ventilation holes
Dimensions and clearances
Models Product Width
(side to side)
Product Depth
(front to back)
Product Height
(below benchtop)
CT560C 578 mm 511 mm 60 mm
CT5602F 578 mm 511 mm 60 mm
CT2802 289 mm 511 mm 55 mm
CT6551S
(cooktop) 578 mm 511 mm 45 mm
(controls) 88 mm 511 mm 63 mm
270 3mm
(CT2802
COOKTOP)
CT6551S
(CONTROL
PANEL)
Cutout for
CT6551S only
70 3mm
25mm
(min)
CT560C, CT5602F, CT6551S
Fig. 2 Cutout dimensions
Minimum clearance
(below benchtop)
CT560C 70 mm CT2802 60 mm
CT5602F 70 mm CT6551S 65 mm
CT560C, CT5602F, CT6551S CT2802

7
Installation instructions
Installing the control panel (CT6551S models only)
1 Remove the supplied clamps from the cooktop and control panel.
2 Feed the cooktop wiring harness up through the control panel cutout.
3 Remove the control panel cover.
4 Connect the cooktop wiring harness by aligning the numbers/letters on the harness with those
on the control panel connector block (see Fig. 3 below).
Important!
Leave the plastic wiring card attached for future reference.
5 Clamp the wiring harness.
6 Wire the mains power supply to the control panel
and clamp.
7 Replace the control panel cover.
8 Roll the control panel into the cutout.
9 Secure the control panel and the cooktop using the
clamps provided (see ‘Clamping down the cooktop’
following).
Note: two small clamps are supplied and must be used for clamping down the control panel to
the benchtop. These clamps are to be screwed to the sides of the control panel. Three
clamps are provided for clamping down the cooktop itself (see ‘Clamping down the cooktop’
following).
Clamping down the cooktop
Place the cooktop into the cutout and tighten with
the supplied clamps. These will cope with bench
thickness 20-50 mm.
Final checklist
TO BE COMPLETED BY THE INSTALLER
Is the product earthed?
Check that the power supply cable is NOT touching the product. This will ensure that the cable is
not damaged by heat from the product.
Is the product clamped down securely?
Check that all the elements function correctly by switching on all of them and leaving them on
for at least one minute. Are all elements glowing?
Is the ‘Element On’ indicator light functioning when you turn an element on? Turn all the
elements on individually to check.
To check that the ‘Surface Hot’ indicator light functions correctly, switch off all the elements. Is
the ‘Surface Hot’ indicator light functioning?
Fig. 4 Clamping down the cooktop
54PNEEN321
54PNEEN321
Control panel
connector block
Plastic wiring card
Fig. 3 Using the plastic wiring card to align the
numbers/letters on the harness with those on
the control panel connector block.

8Introduction
About your new cooktop
Thank you for buying a Fisher & Paykel ceramic glass cooktop. Once it is installed and ready to
use, you will want to know everything about it to make sure you get excellent results right from
the start.
This guide introduces you to all its special features. We recommend you read the whole guide
before using your new cooktop, for both safety and cooking success.
For more information, go to www.fisherpaykel.com
Before using your new cooktop
Before using your new cooktop, please:
Read this user guide, taking special note of the ‘Safety and warnings’section.
Remove any protective film that may still be on your cooktop.
1 Front element
2 Front element control knob
3 Rear element
4 Rear element control knob
5 ‘Surface Hot’ indicator lights
Fig.5 Cooktop layout-CT2802 models
1
3
5
24
Fig.6 Cooktop layout-CT560C models
(available in Australia only)
1 Left front element
2 Left front element control knob
3 Left rear element
4 Left rear element control knob
5 Right rear element
6 Right rear element control knob
7 Right front element
8 Right front element control knob
9 ‘Surface Hot’ indicator light
10 ‘Element On’ indicator light
2
3 5
1
7
9
10
468