Fisher & Paykel ELBA CI604ELTB User manual

Induction cooktop
CI604ELTB, CI704ELTB & CI904ELTB
models
NZ AU
INSTALLATION INSTRUCTIONS
591066C 11.16

1
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website listed on the back cover or contact your local ELBA by Fisher & Paykel dealer.
1SAFETY AND WARNINGS
WARNING!
Electrical shock hazard
Disconnect the appliance from
the mains electricity supply
before carrying out any work or
maintenance on it.
Connection to a good earth wiring
system is essential and mandatory.
Alterations to the domestic wiring
system must only be made by a
qualified electrician.
Failure to follow this advice may
result in electrical shock or death.
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result
in injury or cuts.
IMPORTANT SAFETY INSTRUCTIONS
● Particular attention shall be given to
the relevant requirements regarding
ventilation.
● Read these instructions carefully before
installing this product.
● Please make this information available
to the person installing the appliance as
it could reduce your installation costs.
● This appliance is to be installed and
serviced only by an authorised person.
● Installation must comply with your
local building and local electricity
regulations.
● The manufacturer accepts no
responsibility for the incorrect
installation of appliances. Incorrect
installation may result in personal injury,
damage to property and may invalidate
any warranty or liability claims.
● Do not modify this appliance.
● Do not use or store flammable materials
on or near this appliance.
● Packing elements (eg plastic bags,
polystyrene foam, staples, packing
straps etc) and tools should not be left
around during and after installation,
especially if they are within easy reach
of children, as these may cause serious
injuries.
!
!

2
1SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTIONS
Before you install the appliance, please make sure that
● a suitable disconnection switch is
incorporated in the permanent wiring,
mounted and positioned to comply with
the local wiring rules and regulations.
A means of disconnection with at least
a 3 mm air gap contact separation in
all poles must be incorporated into the
fixed wiring in accordance with the
wiring rules, unless the local wiring rules
allow for alternative means.
● the benchtop is made of a heat resistant
material.
● the power supply cable is not accessible
through cupboard doors or drawers.
● there is adequate flow of cool air from
the cabinetry to the base of the cooktop.
You may ventilate from adjacent
cupboards, but ensure that the available
air supply will not be restricted.
● the ventilation area must be at least two
50mm diameter holes or of an equivalent
area.
● the isolating switch is easily accessible
by the customer.
● you use heat-resistant and easy-to-clean
finishes (such as ceramic tiles) for the
wall surfaces surrounding the cooktop.
● the cooktop will not be installed directly
above a dishwasher, fridge, freezer,
washing machine or clothes dryer, as
the humidity may damage the cooktop
electronics.
IMPORTANT SAFETY INSTRUCTIONS
● if the cooktop is installed above an oven,
the oven has a built-in cooling fan.
● the installation will comply with all
clearance requirements and applicable
standards and regulations.
● you consult local building authorities and
by-laws if in doubt regarding installation.
When you install the appliance
● We do not recommend you flush mount
or seal this appliance into the bench
with silicone or glue. Doing so will make
future servicing difficult. ELBA by Fisher
& Paykel will not be liable for any costs
associated with removing or replacing a
sealed-in appliance, nor for repairing any
damage that may be incurred by doing
this.
● Seal exposed bare edges of the cutout
with an oil-based paint or moisture-
proof polyurethane to prevent possible
moisture creeping between the cooktop
trim and the benchtop.
● Take extreme care not to chip, crack,
or break the top glass surfaces during
installation. A heavy metal tool or part
accidentally dropped on the glass could
damage it.
● If, after following the instructions given,
correct performance cannot be achieved,
please contact your nearest Fisher
& Paykel Authorised Service Centre,
Customer Care, or contact us through
our local website listed at the end of this
document.

3
2PARTS SUPPLIED
Clamping brackets (4)
and screws (4)
Installing multiple products
● Note: We recommend installing products in separate cutouts with a minimum distance of 5 mm between the glass edges.
● If installing multiple products adjacent to each other within the same cutout, a separate joining strip kit is required for installation.
● The kit is available from the nearest ELBA by Fisher & Paykel Authorised Service Centre or our website www.fisherpaykel.com.
● If installing different products adjacent to each other (eg a wok burner next to an induction cooktop), the minimum clearance measurements for the different products may vary.
Always use the greater distance.
Foam tape (1)

4
G
H
I
B
E
C
AD
F
3PRODUCT & CABINETRY DIMENSIONS
PLAN
FRONT
PLAN
FRONT PROFILE
CI904ELTB CI704ELTB CI904ELTB
PRODUCT AND CABINETRY DIMENSIONS mm mm mm
AOverall height of product (including terminal block below top of chassis) 61 61 61
BOverall width of product 600 700 900
COverall depth of product 530 530 530
DHeight of chassis (including terminal block below top of chassis) 57 57 57
EWidth of chassis 555 555 755
FDepth of chassis 485 485 485
GOverall width of cutout 560 560 760
HOverall depth of cutout 490 490 490
ICorner radius of cutout max. 10 max. 10 max. 10
Note:
Electrical connection is made at the centre rear

5
BD
E
C
C
A
ISO
FRONT
CI604ELTB CI704ELTB CI904ELTB
CLEARANCE DIMENSIONS mm mm mm
AMinimum clearance from rear edge of cutout to nearest combustible surface 30 30 30
BMinimum clearance from glass surface to rangehood 650 650 650
CMinimum clearance from side edges of cutout to nearest combustible surface 30 80 80
DMinimum clearance from benchtop to overhead cabinet not directly above the cooktop 450 450 450
EMinimum clearance below top of benchtop to:
Rear top of oven* installed below cooktop or cabinetry 82 82 82
* The oven installed below the cooktop MUST have a cooling fan.
4CLEARANCE DIMENSIONS
min. 75 mm
Alternatively
2x 50mm holes
in side wall
to allow adequate
cool air
min. 4 mm
min. 4 mm
Drawer or other obstruction
Oven with cooling fan
Ventilation gap
must be present
20 mm
Alternatively
2x 50mm holes
in side wall
to allow adequate
cool air
E
WARNING!
This cooktop requires
adequate supply of cool air
to fully function.
The base of the cooktop
must have direct
unrestricted ventilation to
the room where the
cooktop is installed. Follow
the requirements shown.
!

6
E
AD
F
B
C
5FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED)
CI604ELTB CI704ELTB CI904 ELTB
PRODUCT AND CABINETRY DIMENSIONS mm mm mm
AOverall height of product (including terminal block below top of chassis) 61 61 61
BOverall width of product 600 700 900
COverall depth of product 530 530 530
DHeight of chassis (including terminal block below top of chassis) 57 57 57
EWidth of chassis 555 555 755
FDepth of chassis 485 485 485
GOverall width of routered recess 605 605 905
GIWidth of cutout 560 560 760
HOverall depth of routered recess 535 535 535
HIDepth of cutout 490 490 490
ICorner radius of cutout max. 10 max. 10 max. 10
JCorner radius of routered recess max. 2 max. 2 max. 2
KHeight of routered recess 555
LMinimum clearance below top of benchtop to:
rear top of oven* installed below cooktop or cabinetry
thermal protection barrier
87
87
87
87
87
87
WARNING!
We do not recommend flush mounting and
sealing as servicing requires the cooktop to
be removed from the benchtop. The owner
carries all risk for flush mounting the cooktop.
The owner must ensure the cooktop has been
cut out from the benchtop before servicing
can be carried out. ELBA by Fisher & Paykel
will not be liable for any costs associated with
removing or replacing a flush-mounted and/
or sealed-in product, nor for repairing any
damage that may be incurred by doing this.
!
G
G
K
L
HH
IJ
PLAN PLAN
FRONT
FRONT
PROFILE
Note:
Electrical connection is
made at the centre rear

7
5FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED)
1
5 mm
1
2
3
min. 150 OC rated
2
1
TO REMOVE PRODUCT
Ensure silicone does not leak underneath glass.
12-40mm 40mm +
view from below
No. of brackets and slot positions depends on model
Fit a minimum of 2 brackets on opposing sides
AROUTER THE BENCHTOP TO THE SPECIFIED DEPTH
DAPPLY SILICONE
BFIT THE CLAMPING BRACKETS
EWIPE OFF EXCESS SILICONE
CMASK OFF THE AREA TO BE SILICONED
FIF REMOVING PRODUCT, CUT
AROUND THE SILICONE

8
6DISCARD PACKAGING
8APPLY ADHESIVE FOAM TAPE AROUND GLASS EDGE
7PLACE COOKTOP UPSIDE DOWN
9LOWER GENTLY INTO THE CUTOUT
Recycle responsibly
IMPORTANT! - To avoid damage to the glass, ensure there is a protective cover underneath it.
IMPORTANT!
Beware sharp edges
1Apply the foam seal around the glass
overhang, 5 mm in from the edge
of the glass, with the adhesive side
facing down to form a continuous
seal around the cooktop.
2Using a sharp cutter or trimmer
knife, trim the excess sealing
material around the edge of the
cooktop. Take care not to damage
the benchtop.
Foam Tape
Adhesive side
Ensure edge of tape
lines up with outer
edge of cooktop