Fisher & Paykel OB60SL11DEPX1 User manual

ERUTAREPMETNOITCNUF
ERUTAREPMETNOITCNUF
YOUR OVEN
OB60SL11DCPX1
OB60SL11DEPX1
SETTING THE CLOCK
THE CONTROL PANEL
FIRST USE
1 REMOVE ALL CABLE TIES & PACKAGING
HOLDING THE SHELVING IN PLACE
2 REMOVE SHELVES FROM THE OVEN
Keep this document handy for easy reference.
For detailed information on the other features of your oven, see your ‘User guide’.
Before using your oven, make sure you read the full ‘User guide’, with special attention to the ‘Safety and warnings’ section.
For contact information or if you require service, assistance or replacement parts, see the end of this document or your ‘Service & warranty’
booklet.
1 Control panel
2 Oven vent louvres
3 Step down oven wire shelf
4 Oven light
5 Telescopic sliding shelf (x2)
6 Side rack
7 Oven wire shelf
8 Oven door and handle
9 Oven seal
Accessories:
10 Meat probe
11 Grill rack
12 Smokeless grill tray
13 Deep Roasting dish
14 Flat baking tray
11
10
12
13
14
2
3
4
5
6
7
8
19
Your oven comes with one wire shelf, two telescopic sliding shelves and a drop down wire shelf.
The following shows you how to remove and reposition the shelves to your preferred position
We recommend you then condition the oven.
You set the clock within the user preference menu. To learn more about the user preference menu, refer to your User guide.
Note: If you do not wish to set the time initially when the oven is first switched on at the wall, press the cancel
-+
-+-+
button to exit the clock setting.
If you want to set the clock later, follow the steps under ‘To change the time’.
To change the time
(within the user preference menu)
When the oven is first switched on at the wall
1 Remove all the shelving, taking special care with the telescopic
sliding shelves.
2 To remove a telescopic sliding shelf, grip it at the front (making
sure you are gripping the wire shelf and the sliding frame
together), lift upwards and pull it out of the oven.
For your safety, the wire shelf and telescopic sliding frame are
built together as one unit and are not separable.
Function indicators
(see ‘Oven functions’)
Function dial Temperature
indicator
Temperature
dial
Function halo
Temperature
halo
Control lock indicator (see
‘Locking the control panel’)
if lit:
Control panel is locked
Timer indicator
(see ‘Using the
timer’)
if lit:
Timer is
counting down
Door lock indicator
if lit:
Door is open when Self
Clean function selected.
See ‘Using the Self Clean
function’ in User guide.
Rotisserie indicator
(see ‘Using the
Rotisserie’) in the
User guide
if lit:
Rotisserie is
in use
Cooking time indicator (see ‘Automatic cooking’) in User guide
if lit:
Automatic cooking time is set
Meat probe indicator
(see ‘Using the meat probe’) in User guide
if lit:
Meat probe is in use
(display will alternate between probe set
temperature and internal temperature
of the meat)
Stop time indicator
(see ‘Automatic cooking’) in User guide
if lit:
Automatic stop time is set
Display
Scroll Select Cancel
1 Press and hold the left and right scroll
-+
-+-+
-+
-+-+
buttons together for 3 seconds
to enter the user preference menu.
The display will either show 12 Hror 24
Hr
2 Press the select
ERUTAREPMETNOITCNUF
button to confirm.
The display will flash.
3 Follow steps 2-5 left to set the time.
At step 2a, you also now have the
ability to scroll between 24 Hr,
12 Hr and OFF (turns the display off).
Refer to the User guide to learn more
about this feature.
3 Press the left and right scroll
-+
-+-+
-+
-+-+
buttons to set the time.
1
The display will flash 24 Hr.
4 Press the select
ERUTAREPMETNOITCNUF
button to
confirm.
2a Press the right scroll
-+
-+-+
button to scroll
between 24 Hrand 12 Hr
2b Press the select
ERUTAREPMETNOITCNUF
button to confirm.
continued over
Locking the control panel
To lock, press and hold the select
ERUTAREPMETNOITCNUF
button until the lock indicator light
ERUTAREPMETNOITCNUF
comes on.
To unlock, press and hold the
cancel
ERUTAREPMETNOITCNUF
button until the lock
indicator light
ERUTAREPMETNOITCNUF
flashes and then
goes out.
NZ AU GB IE
BUILT-IN OVEN
QUICK START GUIDE

There will be a distinctive smell and a small amount of smoke during the conditioning of the oven.
This is normal, but make sure the kitchen is well ventilated during the conditioning.
Once cooled, wipe out the oven with a damp cloth and mild detergent, and dry thoroughly.
It is important to condition your oven before using it for cooking and baking. Conditioning will burn off any manufacturing residues and ensure
that you get the best results right from the start.
1 Make sure you have removed ALL the cable ties used to secure the shelving during transit.
2 Make sure you have set the clock.
3 Make sure all the shelves are fitted.
USING THE TIMER
FOR MORE INFO
FIRST USE
4 CONDITION THE OVEN
3 REPLACE SHELVING IN YOUR PREFERRED POSITIONS
Stop Notch
Shelf stop
Guard rail
Guard
rail
Front bar
Rear shelf tagFront shelf tag
We recommend placing the telescopic sliding shelves on positions 2 and 4 as these are the shelf positions most often used.
To replace a wire shelf, check the guard rail (as shown) to make sure the shelf is the right way up.
slide it horizontally back along the side racks ensuring it is level and the stop notch is facing down.
To replace a telescopic sliding shelf, position it so that the front bar is toward you, as shown.
Check that the sliding frame is not extended.
Check the guard rail (as shown) to make sure the shelf is the right way up.
Position the shelf so that it is level and the rear shelf tag at the back of the sliding frame rests behind the side rack wire (as shown).
Then push the sliding shelf all the way to the back of the oven, until the front shelf tag drops into place behind the side rack wire.
For your safety, the wire shelves and telescopic sliding frames are built together as one unit and are not separable. This means that when placed
properly on the side racks, the slides will prevent the wire shelves from tilting when pulled towards you.
To prevent the tags from lifting off the side racks, take care to slide the shelves forward horizontally.
NOITCNUF NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
NOITCNUF NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
NOITCNUF NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
Replacing a wire shelf
Shelf positions
Replacing a telescopic sliding shelf
7
Leave the temperature at 200
o
C
for 5 minutes.
The halo will remain white.
1 Select the timer
-+
-+-+
by pressing
the right scroll
-+
-+-+
button once.
The timer
-+
-+-+
indicator will appear
and the colon will flash.
2 Press the select
ERUTAREPMETNOITCNUF
button to
confirm.
The display will flash to indicate
the timer is ready to be set.
3 Set the time by pressing the
scroll
-+
-+-+
-+
-+-+
buttons.
Holding the buttons down
will speed up the scrolling.
4 Press the select
ERUTAREPMETNOITCNUF
button to
confirm.
The timer will then begin to
count down.
If you want to check the time
of day, press the cancel
-+
-+-+
button once.
Press the right scroll
-+
-+-+
button
to scroll back to the timer.
8 When you have finished, turn the function dial to
Off
NOITCNUF NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
. The halos will go out.
You can use the timer at any time, even if you are not using the oven.
If the time is more than an hour, the display will count down in minutes (hr:min). If it is less than an hour, it will count down in seconds (min:sec).
You can set the timer for up to 23 hours 59 minutes.
Important!
The timer does NOT turn the oven off.
To modify the timer setting
1 Make sure the display shows the remaining time counting down.
2 Press the select
ERUTAREPMETNOITCNUF
button.
3 Press the scroll
-+
-+-+
-+
-+-+
buttons to set a new time.
4 Press the select
ERUTAREPMETNOITCNUF
button to confirm.
To cancel the timer setting
1 Make sure the display shows the remaining time counting down.
2 Press the cancel
-+
-+-+
button until the display shows the time of day and the timer
-+
-+-+
indicator disappears.
When the set time is up
The display will show 0:00 and a tone will sound every 15 seconds.
Press any button to stop the tone sounding. The display will revert to showing the time of day.
For detailed information on the
other features of your oven
For warranty information
If you…
have any questions or comments
need a Fisher & Paykel authorized
technician to service your product
need replacement parts or accessories
want to register your product
see your ‘User guide’
see your ‘Service and warranty’ booklet
see your ‘Service and warranty’ booklet or contact us
NZ toll-free, 24/7 0800 372 273
AU toll-free, 24/7 1300 650 590
GB toll-free, 24/7 0845 066 2200
IE toll-free, 24/7 1800 625 174
www.fisherpaykel.com
590480C 08.17
NOITCNUF
NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
NOITCNUF
NOITCNUF
NOITCNUF
ERUTAREPMET ERUTAREPMET
NOITCNUF NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
4 Select the Bake
NOITCNUF NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
function.
The halo will glow white.
Each function has a preset
temperature and so the oven
will start heating at the Bake
preset temperature of 180
o
C.
5 Set the temperature to 200
o
C for 30 minutes.
While the oven is heating up, the temperature halo
will glow red and the temperature indicator will
alternately show the actual and set temperatures.
When the oven has reached set temperature, a tone
will sound and the halo will turn white.
6 After 30 minutes is up,
select the Fan Grill
NOITCNUF NOITCNUF NOITCNUF
ERUTAREPMET ERUTAREPMET
function.
1
2
6
5
4
3