Fisher & Paykel BI453 User manual

Built-in oven
Installation instructions
NZ AU
BI453 and BI603 models

Important!
To avoid hazard, follow these instructions carefully before installing or using this product.
Please make this information available to the person installing the product as it could reduce
your installation costs.
This oven is to be installed and connected to the electricity supply only by an authorised person.
Installation must comply with your local building and electricity regulations.
Failure to install the oven correctly could invalidate any warranty or liability claims.
Before you install the oven, please make sure that
A suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned
to comply with the local wiring rules and regulations. The switch must be of an approved
type installed in the fixed wiring and provide a 3 mm air gap contact separation in all poles in
accordance with the local wiring rules.
In Australia and New Zealand, a switch of the approved type with a 3 mm air gap must be installed
in the active (phase) conductor of the fixed wiring.
The location of the oven connection socket (if fitted) is outside the cavity if the product is flush to
the rear wall.
The electrician allows at least 1.5 m free length of connection cable within the cavity for ease of
installation and servicing of the product. The mains cable should not touch any hot metal parts.
Note: the oven has a recess at the bottom rear to allow for the cable entry. The mains cable must
enter the cavity in this recessed area.
The cavity is completely sealed with no gaps. This allows the cooling air to vent correctly, under
the oven and through the oven frame. If you do not seal the cavity, the surrounding cabinetry may
overheat and become damaged.
The benchtop and oven cavity are square and level, and are the required dimensions.
The height from the floor suits the user.
The oven door/s can open fully without obstruction.
When you install the oven
For ovens with cooktops, make sure that the controls connect to the correct heating elements.
Do not seal the oven or cooktop into the cabinetry with silicone or glue. This makes future
servicing difficult. Fisher & Paykel will not cover the costs of removing the oven or cooktop, or of
damage caused by this removal.
Fit the washers to the screws (supplied) and use them to secure the oven to the cabinetry. Do not
over-tighten the screws. You could damage the oven frame enamel.
Do not stand on the door, or place heavy objects on it.
Safety and warnings
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.

1
Contents
Product and cabinetry dimensions 2
Installing the oven 6
Installing the cooktop 7
Important!
SAVE THESE INSTRUCTIONS

2Product and cabinetry dimensions
Single oven models
A
B
CE
D
F
G
H
J
K
L
Product and cabinetry dimensions (mm)
BI453
models
BI603
models
Aoverall height of product 450 595
Boverall width of product 595 595
Coverall depth of product (without handle) 562 562
Dheight of chassis 433 578
Ewidth of chassis 550 550
Fdepth of chassis 542 542
Gdepth of oven frame and control panel (excl. knobs) 20 20
Hdepth of oven door (open) (measured from front of oven frame) 320 465
Iminimum inside width of cavity 560 560
IIoverall width of cavity 600 600
Jinside height of cavity 438 583
JIoverall height of cavity 455 600
Kminimum inside depth of cavity 550 550
Lflush fitting cabinetry clearance 20 20
Note: If installing a cooktop above the oven ensure adequate clearance is provided for the cooktop as per the
cooktop manufacturer’s instructions.
I
Installation diagrams for illustration purposes only
I
I
J
I
2.5 mm
16-20 mm
Ensure the cavity is completely sealed with no gaps
L

3
Product and cabinetry dimensions
Double oven models
Product and cabinetry dimensions (mm)
BI603 2
models
BI603ED
BI603 1.5
models
Aoverall height of product 1077 932
Boverall width of product 595 595
Coverall depth of product (without handle) 562 562
Dheight of chassis 1060 915
Ewidth of chassis 550 550
Fdepth of chassis 542 542
Gdepth of oven frame and control panel (excl. knobs) 20 20
Hdepth of oven doors (open) (measured from front of oven frame) 465/465 465/320
Iminimum inside width of cavity 560 560
IIoverall width of cavity 600 600
Jinside height of cavity 1065 920
JIoverall height of cavity 1082 937
Kminimum inside depth of cavity 550 550
Lflush fitting cabinetry clearance 20 20
Mminimum clearance from floor to bottom of cavity 380 525
A
B
C
D
E
F
G
H
I
J
K
L
I
I
J
I
M
Ensure the cavity is completely sealed with no gaps

4Product and cabinetry dimensions
Product and cabinetry dimensions (mm)
BI603 CTE
models
Aminimum inside width of cavity 560
AIoverall width of cavity 600
Binside height of cavity 583
BIoverall height of cavity 600
Cminimum inside depth of cavity 550
Dflush fitting cabinetry clearance 20
Eminimum clearance from benchtop surface to
top surface of oven chassis 55
Built-in oven/cooktop
combination
BENCHTOP
OVEN
Please refer to cooktop
installation instructions
p/n 599100
Dimensions as
per single oven
model BI603
B
C
D
A
E
E
B
A
I
B
I
Ensure the cavity is completely sealed with no gaps

5
Built-in oven/microwave
combination model
Product and cabinetry dimensions
B
C
D
H
J
A
E
F
G
H
K
L
M
I
Product and cabinetry dimensions (mm)
BI603 XC
models
Aoverall height of product 932
Boverall width of product 595
Cdepth of microwave (excl.frame and control panel) 455
Ddepth of microwave frame and control panel 30
Ewidth of microwave chassis 558
Fdepth of oven chassis 542
Gdepth of oven frame and control panel (excl. knobs) 20
Hdepth of oven door (open) (measured from front of oven frame) 465
Idepth of microwave door (open) 440
Jminimum inside width of cavity 560
JIoverall width of cavity 600
Kminimum inside height of cavity 935
Lminimum inside depth of cavity 550
Mflush fitting cabinetry clearance 20
J
I
Ensure the cavity is completely sealed with no gaps
545

6Installing the oven

O
MM








12
34
56

7
Installing the cooktop


O
MM
12
34
56
Please refer to cooktop
installation instructions
p/n 599100

8