Fisher & Paykel IZONA CoolDrawer RB90S User manual

Important!
Disconnect power to surrounding appliances before preparing cavity.
Recommended to allow the vertical removal of the refrigerator bins.
WARNING!
Electrical shock hazard
Disconnect product from main power supply before installing appliance.
Failure to do so may result in electrical shock or death
Important safety precautions!
Installation of the CoolDrawer requires competent mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the CoolDrawer installation, the Installer must perform the Final Check List.
Remove all packaging materials supplied with the CoolDrawer.
The CoolDrawer is manufactured for indoor use only.
Important!
SAVE THESE INSTRUCTIONS
The model shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website
www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
SAFETY AND WARNINGS
WARNING!
Cut hazard
Take care – panel edges are sharp.
Failure to use caution could result in injury or cuts.
1
2
The CoolDrawer MUST be installed to allow for future removal from the enclosure if service is required.
Do not seal the CoolDrawer into the cabinetry with silicone or glue. Doing so will make future servicing
difficult. Fisher & Paykel will not be liable for any costs associated with removing or replacing a sealed-in
product, nor for repairing any damage that may be incurred by doing this.
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the
power supply cord.
Failure to install the CoolDrawer correctly will invalidate any warranty or liability claims.
If the power supply cord is damaged, it must be replaced. Parts are available from your Fisher & Paykel
Appliances Authorised Service Centre.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capacities, or lack of experience and knowledge unless they are supervised or given instruction
concerning use of the appliance.
Cabinetry must be sufficiently robust to support a combined product and food load of 100 kg. Bearers may
be required to support the internal shelf.
Before you install the CoolDrawer, please ensure that
The switched power outlet must be outside the refrigerator drawer cavity so that it is accessible after
installation.
The switched power outlet must be located outside the cavity, within 1400 mm from the CoolDrawer
cavity if situated on the left-hand side of the cavity and within 850 mm if situated on the right-hand side
of the cavity.
The services hole in the refrigerator cavity needs to be large enough for the power supply plug to fit
through.
PRODUCT DIMENSIONS
PARTS SUPPLIED
4
5CAVITY PREPARATION
CoolDrawer
Installation instructions
RB90S model FRAMELESS CABINETRY
WARNING!
Tipping hazard
Do not operate this appliance until it has been securely anchored inside the cabinetry.
The cabinet must be securely anchored to the floor.
Failure to use caution could result in injury or cuts.
Product dimensions (mm)
CoolDrawer
RB90S
Aoverall height of product (inc. installation brackets) 640
Boverall width of product 855
Coverall depth of product (excl. drawer panel; inc. power cord) 557
Ddepth of drawer (open) (excl. handle) 520
Installation diagrams for illustration purposes only
A
DH
Cabinetry dimensions (mm)
CoolDrawer
RB90S
Aoverall width of cabinetry frame 900
Bminimum inside width of cabinetry frame 864
Cinternal height of cabinetry to top of spacer block 644
Dinternal height of cabinetry*
(to allow for product and outlet duct height)
min. 665
max. 764
Eminimum height of toe kick 75
Fminimum depth** of toe kick 40
Gminimum distance from front of cabinetry to rear wall 560
Hwidth of spacer blocks 50
*Minimum internal height of cabinetry can be 644 mm if outlet duct is not used.
**All depth measurements are taken from the front face of the cabinetry frame (not drawer panel)
Minimum clearances (mm)
2 mm
13 mm
E
B
C
D
G
F
F
C
G
Installation
trims (2)
Installation brackets
(left-hand and right-
hand side) (2)
Outlet duct (1)Trim brackets (4) Drawer Panel
attachment
hooks (3)
Power
cord (1)
Note: Services can be located
either side of CoolDrawer.
max.
20 mm
max. 850 mm
min. ø50 mm
Benchtop
Panel
min. 535 mm
Installation diagrams for illustration purposes only
Drawer Panel
16-20 mm
False Panel
(896 mm)
height of False Panel
4 mm
6INTEGRATED PANEL PREPARATION
A
B
min. 130 mm
Phillips 16 mm
wood screw (6) Pan Head 16 mm
screw (12)
Pan Head
16 mm
screw (2)
Phillips
16 mm
wood
screws (6)
min. 535mm
min. 130mm
height of
Drawer
Panel
3CABINETRY DIMENSIONS
Shows cutout if cabinetry
depth at minimum
550 mm
Benchtop
Drawer panel
False panel
A
D
E
C
B
Integrated Panel material
16 - 20 mm panel thickness (18 mm recommended).
Maximum weight of 7 kg.
Adequately sealed to withstand moisture (50
O
C @ 80% RH)
Height of Drawer Panel
The following information is required to correctly define your drawer panel height:
Dimension Data Source
AClearance between top of Drawer panel and underside Your kitchen designer
of benchtop
BHeight between underside of cabinetry ceiling Your kitchen designer
and underside of benchtop
CInternal height of cabinetry to top of spacer block 644 mm
DDrawer panel height Calculated from A, B, C & E
EBottom face of Drawer panel to top of spacer block Your kitchen designer
(to ensure that bottom cover of product is not exposed) (Min. 154 mm, Max. 184 mm)
To calculate D complete the following equation:
D = C + B - A - E
i.e. For the F&P prefinished panel:
476 mm = 644 mm + 18 mm - 2 mm - 184 mm
Height of the False Panel
Determine the height of the false panel according to your individual kitchen cabinetry
requirements maintaining a 4 mm gap between panels.
F&P prefinish panel width is 896 mm assuming a 2 mm clearance either side of panel
height (D) is 476 mm.
Note: B must be min. 16 mm to ensure adequate clearance to benchtop.
An internal shelf can be used as an alternative to spacer blocks to
position the product at the correct height. In this case additional
cutouts will be required. Refer to Step 7.
SIDE VIEW

&
'
'
(
( ) *'&
+ ,
'
&
&
' '
&
(
( (
,+)bb
&%'bb
©&+bbbVm#
*%bb
'-&bb
'&*bb
'&*bb b^c#-+%bb
bVm#-+'bb
'*bb
,+bb
)%bb
'
()
&
)+bb
'bb 'bb
'
&
.bb
m(
'#*bb
-.+bb
&bb
*bb
&-bb
(&&bb(&&bb
)&)bb M
&+"'%bb
-
www.fisherpaykel.com 840714 FRAMELESS CABINETRY 09.09
13
18
ATTACH DRAWER PANEL TO FRONT OF DRAWER
FINAL CHECKLIST
Important!
Ensure a minimum of 3 screws
per side are used. The rear screws
must always be used. Horizontal
fixing is also optional.
If the cabinetry does not already have cutouts, ensure the modifications below are made.
Important!
Do not screw in trim
brackets at this stage.
Important!
Ensure the power cord is clipped in place.
(
&
'
'bb
&
'
Hook drawer panel onto
drawer front channel
Close the drawer and
check vertical clearances
Remove the panel and
adjust the TOP
attachment hooks
as necessary
Replace panel on
drawer and confirm
vertical clearances
Slide panel to achieve
horizontal clearances
Open drawer and clamp
panel onto drawer by
tightening the BOTTOM
attachment hook
Close the drawer and ensure it is flush
with adjacent cabinetry. If not, the
product may have to be pulled back
or forward.
Important!
Ensure you check basic operation and perform
the final checklist.
Attach the false panel securely
as recommended by the cabinet
maker.
Important!
The false panel needs to be removable for
servicing.
Secure using vertical
or horizontal fixing
CREATE CUTOUTS IN FRAME
7LOCATE & SECURE INSTALL BRACKETS 8
Important!
Cut outlet duct to be flush
with top of spacer blocks.
9ATTACH OUTLET VENT DUCT 10 ATTACH POWER CORD & TRIM BRACKETS
Important!
Note correct orientation of bracket.
Important!
Be careful not to damage power
supply cord when pushing
product into cavity.
11 MOVE PRODUCT INTO CAVITY 12 FIT DRAWER PANEL ATTACHMENT HOOKS
Attach handle as necessary.
Ensure all screws are flush
with panel surface.
X = 194mm – E, where E
is Bottom face of Drawer
Panel to top of spacer
block, see 6.
14 SECURE PRODUCT TO CABINETRY 15 ATTACH TRIMS TO SIDES OF CABINETRY
16 ATTACH FALSE PANEL 17 CHECK OPERATION
Open drawer and secure product
to cabinetry using four Trim
brackets and screws.
TO BE COMPLETED BY THE INSTALLER
Has all packaging been removed from the appliance?
Is the appliance securely fastened to the cabinetry?
Does the drawer slide freely and close properly?
Has the outlet duct been installed correctly?
Is the appliance level?
Are the panels securely attached?
Have the panels been properly aligned for correct operation and
appearance? Are all clearances even?
Is there clearance between drawer and cabinetry frame?
Has the power cord been plugged into a properly earthed 3-prong outlet,
which has been installed in accordance with all applicable electrical codes?
OPERATION:
Is the control panel lit?
Can you hear the compressor motor running?
When a hand is placed near the toe kick, can airflow be felt under front
right-hand side of appliance?
Have you demonstrated the basic operation to the customer?
Installer’s name:
Installer’s signature:
Installation company:
Date of installation:
LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER
Ensure there is clearance
between panel and cabinetry
when drawer is fully closed
*Only with cabinetry with internal shelf
*