Fisher & Paykel RS7621WR User manual

INSTALLATION GUIDE
NZ AU GB IE
RS6121WR, RS7621WR, RS6121WL
& RS7621WL models
INTEGRATED COLUMN
REFRIGERATOR FREEZER

3
CONTENTS
Safety and warnings 4
Integrated column models 5
Check your appliance 6
Remove pre-installed parts 6
Moving your appliance 7
Supplied parts 8
Required parts 10
Door panel set 11
Door and drawer handle kits 11
Hinge change kit 12
Product dimensions — 610MM model 13
Cavity dimensions — 610MM model 14
Door panel dimensions — 610MM model 15
Custom door panel install dimensions — 610MM model 16
Door clearance — 610MM model 17
Drawer clearance — 610MM model 18
Toe kick dimensions — 610MM model 19
Toe kick install options 20
Product dimensions — 760MM model 21
Cavity dimensions — 760MM model 22
Door panel dimensions — 760MM model 23
Custom door panel install dimensions — 760MM model 24
Door clearance — 760MM model 25
Drawer clearance — 760MM model 26
Toe kick dimensions — 760MM model 27
Dual install options 28
Cavity dimensions — 610MM + 610MM dual install 29
Cavity dimensions — 610MM + 760MM dual install 30
Cavity dimensions — 760MM + 760MM dual install 31
Toe kick panel dimensions — dual install 32
Power supply dimensions 33
Electrical specification 34
Plumbing specification 34
Before installation 35
Install anti-tip bracket 36
Connect water and power supply 38
Position and alignment in cabinetry 40
Secure appliance to cabinetry 45
Remove hanging brackets 46
Install door and drawer panels 47
Install locking bracket 51
Install adjustment brackets 51
Install toe kick panel 52
Install toe kick grilles 53
Install top trim 53
Install water filter 54
Install air flow divider 55
Install cabinet side trims 56
Install door and drawer side trims 57
Dual installation 58
Change the door hinges (optional) 64
Final checklist 70

4
SAFETY AND WARNINGS
SAVE THESE INSTRUCTIONS
WARNING!
To avoid hazard, follow these instructions carefully before installing or using thisappliance.
zPlease make this information available to the person installing the appliance.
zAssume all electrical parts are live.
zDisconnect power supply before servicing and installation.
BEFORE INSTALLATION
z The appliance has front and rear rollers for moving the appliance forward and backward.
Do not move the appliance sideways to avoid damaging the rollers or the floor
covering/surface.
z Ensure your appliance is not exposed to any heat generating appliance eg cooktop, oven
or dishwasher.
z The appliance must be installed by a qualified installer, or Fisher and Paykel trained and
supported service technician to avoid faulty electrical and plumbing connections.
z All connections for electrical power and grounding must comply with local codes and
ordinances and be made by licensed personnel when required.
z Avoid installation of the appliance/s near a ground fault circuit interrupter (GFCI).
z Ensure the appliance is installed properly. Improper installation that results in appliance
failure is not covered under the appliance warranty.
UNPACKING
z The appliance is heavy and requires at least twopersons to move and install.
z Remove the installation kit (internal box) and trims kit (external box) while the product is
still on the pallet.
z Avoid scratching the surface of your appliance when moving or installing.
z Keep the appliance stable and door closed to prevent tipping over when moving to the
installation location.
z Ensure the feet of the appliance are retracted before moving to the installation location.
z If the appliance is damaged, contact your Fisher and Paykel dealer.
z Ensure all components and accessories are complete. Refer to 'Before installation' page.
z Record the default Wifi password, and the model and registration numbers for future
servicing or repair of your appliance.
ELECTRICAL/PLUMBING
z Electrical and water supply connections for these appliances must be located in an
adjacent area or unit (cabinet or cupboard) that are easily accessible in case of repair or
disconnection.
z Ensure an isolating switch is available if electrical connection is not accessible.
INSTALLATION
Cavity preparation
z The anti-tip bracket and fittings supplied must be fitted tothe wall of the finished
enclosure to withstand a 100kg load.
z Ensure that the anti-tip bracket is installed correctly to prevent the possibility of the
appliance tipping forward when the door is open.
! WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electrical shock or death.
• Read and follow the safety and warnings
outlined in this User guide before operating this
appliance.
! WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: panel edges may be sharp.
• Do not put fingers in the drawers when closing.
!WARNING!
Tip Hazard
• This product may tip. Keep children away and
take care. Failure to follow this advice may
result in injury.
• This appliance is top-heavy and must
be secured to prevent the possibility of
tippingforward.
To ensure that the appliance is stable under
all loading conditions:
• Theanti-tip bracket and fittings supplied
must be installed by a professional installer
according tothe installation steps in this guide.

5
SAFETY AND WARNINGS
Positioning inside the cabinetry
z Ensure the door of the appliance is closed when rolling into thecabinetry.
z Ensure the power cord is not run over or damaged when rolling the product into
the cabinetry.
Aligning inside the cabinetry
z For flush installation, ensure the door panels are installed flush with cabinetry front surface.
Ensure the appliance is properly is centred.
z All four corners of the appliance must be supported firmly on the floor to eliminate any
movement. Installing the appliance on a soft, uneven, or not level floor may cause twisting
and poor door sealing.
Fixing inside the cabinetry
z Use low speed, low torque setting when using a powered driver for the screws when fixing
or aligning the product.
z Make sure to remove the depth alignment brackets before fixing theappliance inside the
cabinetry.
z Open the appliance door to remove the alignment brackets from both sides of the
appliance, and then re-tighten the screws.
Installing the door panel
Stainless steel panel
z Protect the finish of the Fisher and Paykel Stainless Steel door panels from any scratch
or damage.
z Remove the blue tape attached to inner edges of the door panels after the handles are
installed.
z We recommend to load the shelves in the appliance door with weights to ensure an
accurate door panel gap width. Load 15kg for 610mm models, and 20kg for 762mm
models.
Custom panel
z If using Custom door panels, ensure they are prepared as per 'Custom door panel install
dimensions' section.
z The thickness of the custom door panel can vary as long as the screws do not penetrate
beyond the full depth of the door panel, and as long as the overall weight of door panel
does not exceed the allowable weight. Refer to 'Door panel dimensions' for maximum door
panel weight of your product.
z Do not place the handle holes in marked areas to avoid clashing with panel
attachment brackets.
z Minimum panel thickness where screw hole is drilled must be 16mm.
Switching the door hinge (optional)
z Door hinges are interchangeable for each model. A hinge change kit is available and can be
purchased separately if you prefer to change from ‘right hand hinge’ to ‘left hand hinge’ or
vice versa.
INTEGRATED COLUMN MODELS
RS6184WR
Refrigerator-Freezer (610mm)
Right Hinge
RS7684WR
Refrigerator-Freezer (762mm)
Right Hinge
RS6184WL
Refrigerator-Freezer (610mm)
Left Hinge
RS7684WL
Refrigerator-Freezer (762mm)
Left Hinge

6
Ensure you follow the unpacking steps printed on the packaging box of your appliance. Check
that your appliance is the correct model as per your order. Check that the components and
install kits are complete.
c fe
Remove the pre-installed parts. Keep
all parts to use later.
A Top trim
B Top door extrusion
C Top grille
D Bottom grille
E Toe kick mounting plate
F Air flow divider
d
CHECK YOUR APPLIANCE
Remove the trims kit at the back of
the appliance. The kit contains:
1 Top door panel side extrusion
2 Bottom drawer panel
side extrusion
3 Bottom drawer top trim
4 Cabinet side trim
Remove the installation kit and
miscellaneous items kit from inside
the appliance.
AB
REMOVE PRE-INSTALLED PARTS
2 3 41
INTEGRATED COLUMNS
RS4621F, RS6121F, RS7621F,
RS6121S & RS7621S models
INSTALLATION GUIDE
NZ AU GB EU
849164B 10.18

7
Hand truck
Follow the steps below to move your appliance to the install location. Be careful when tilting
the appliance forward/backward. Tape the door shut to prevent opening while moving the
appliance.
MOVING YOUR APPLIANCE
Tilt the appliance slightly forward
and insert the hand truck between
pallet and appliance. Tilt backward to load appliance
onto hand truck and push to install
location
24
Remove the brackets from the
non-hinge side of the pallet.
1Restrain the appliance with
strap and remove the remaining
brackets.
4
Strap

8
SUPPLIED PARTS
#8 x 19 Countersunk Twin Thread Posi Screw
#8 x 19 Countersunk Twin Thread Posi Screw
Depth alignment gauge (4) Barbed plug (2) 8Gx16 Countersunk screw (7)
#10x40 Pan Head Philips Screw
#10x40 Pan Head Philips Screw
Anti-tip bracket (1) Masonry plug (4) 10-12x35mm crosshead screw (5)
Side bracket (6) Bracket slider (6) Side spacer bracket (6)
#8 x 16 Mush Washer Twin Thread Philips Screw
#8 x 16 Mush Washer Twin Thread Philips Screw
For Custom door panels:
M5x12 Cross-head screw (32)
Hinge limiting pin (3) Air toe kick seal (1) Locking clip (2)
ANTI-TIP BRACKET ASSEMBLY
Supplied in separate bags
DOOR PANEL ATTACHMENT KIT INSTALL FASTENERS KIT
MISCELLANEOUS PARTS

9
USER GUIDE
US CA NZ AU GB IE SG HK
863023A 09.19
INTEGRATED COLUMN
WINE CABINET
RS2484VL2K1, RS2484VR2K1,
RS6121VL2K1, RS6121VR2K1
models
INTEGRATED COLUMNS
WINE CABINET
RS2484VL2K1, RS2484VR2K1,
RS6121VL2K1, RS6121VR2K1
models
INSTALLATION GUIDE
US CA NZ AU GB IE SG HK
863020A 09.19
User guide (6) Installation guide (1)
SERVICE & WARRANTY
SERVICE ET GARANTIE
ΣΈΡΒΙΣΚ ΑΙ ΕΓΓΎΗΣΗ
SERVIZIO E GARANZIA
SERVICE & GARANTIE
HUOLTO JA TAKUU
SERVICE OG GARANTI
保修和维修
服務和保修
Service & Warranty (1)
Collet locking clip (1) Water filter (1)
1/2 BSP Stainless steel braided hose
with adaptor (1)
1/4” (6.35mm) Adaptor (2)
Top door panel side extrusion (2) Cabinet side trim (2)
Bottom drawer panel side extrusion (2) Bottom drawer top trim (1)
SUPPLIED PARTS
Door spanner (1) M4 Hex key (1)
TRIMS INSTALL KIT (EXTERNAL BOX)
SUPPLIED TOOLS
WATER FILTER KIT
MISCELLANEOUS ITEM PACK

10
Used for dual or multiple installation of appliances. Can be purchased separately through an
authorised Fisher and Paykel dealer. Visitfisherpaykel.com for more information.
Top joiner fastener kit
M5x20 Cap screw (1) M5x16x1 Plain washer (1)
Bottom joiner fastener kit
M6 Washer 843453
M5 Washer
M5 x20 Cap Screw 847984
M6 x 12 Cap Screw 248072
8Gx16 Mush Washer 840371
10 x 50 Dual Lock
M6 Nut 839455
M5 Nut 839107
M6x16 screw plastic washer
M6x16 Washer screw (1) M6x12x3.2 Plastic washer (1) M6 Hex nut (1)
Top joiner bracket kit
#8 x 16 Mush Washer Twin Thread Philips Screw
#8 x 16 Mush Washer Twin Thread Philips Screw
8Gx16 Mush washer screw (2) Central spacer (1)
Not supplied and must be provided by the installer.
Powered driver Flathead screwdriver Ruler
Hacksaw Cross-head screwdriver Pencil
Cutter T20 star-head screwdriver 13mm socket wrench
Hand truck
Not supplied and can be purchased separately through an authorised Fisher and Paykel dealer.
Visitfisherpaykel.com for more information.
Standard toe kick height is 102mm forstandard
stainless steel door panel.
For Custom door panel installation, atoe
kick 50-152mm must be fitted andadjusted
accordingly.
An extra bottom grille is required for 50mm
toe kick installation. You can purchase the extra
bottom grille (Part No. 847542P) online at
fisherpaykel.com.
Toe kick panel (1)
REQUIRED PARTS
TOE KICK PANEL
INSTALL JOINER KIT
REQUIRED TOOLS

11
Not supplied and must be purchased separately through an authorised Fisher and Paykel
dealer. Visitfisherpaykel.com for more information. Select among the handle kit options below:
Custom door panel set
Supplied by customers to match their
cabinetry.
DOOR AND DRAWER HANDLE KITSDOOR PANEL SET
M5 x 14 Mush Head SS Philips Screw
M5 x 14 Mush Head SS Philips Screw
For SS door panels:
8Gx16 Mush washer screw (32)
Stainless steel door panel set
Not supplied and must be purchased
separately through an authorised Fisher
and Paykel dealer. Visitfisherpaykel.com for
more information..
MODEL RH LH
RS61 CA 25711 CA 25712
RS76 CA 25709 CA 25710
HANDLE KIT RS61 RS76
M5 x 25 Pan Head Socket Screw OR M5x25 hex screw
M5 x 25 Pan Head Socket Screw OR M5x25 hex screw
Square aluminum
handle (1)
M5x25 Hex screw (4) CA 25725 CA 25717
M5 x 25 Pan Head Socket Screw OR M5x25 hex screw
M5 x 25 Pan Head Socket Screw OR M5x25 hex screw
Round aluminum
handle (1)
M5x25 Hex screw (4) CA 25727 CA 25719
M5 x 25 Pan Head Socket Screw OR M5x25 hex screw
M5 x 25 Pan Head Socket Screw OR M5x25 hex screw
Square fine aluminum
handle (1)
M5x25 Hex screw (4) CA 26014 CA 25866
M5 x 25 Pan Head Socket Screw OR M5x25 hex screw
M5 x 25 Pan Head Socket Screw OR M5x25 hex screw
Square fine black
handle (1)
M5x25 Hex screw (4) CA 25912 CA 25909

12
HINGE CHANGE KIT
POCKET HINGE TOPRH
POCKET HINGE TOPLH
BRACKET ADAPT K05 BTM RH
BRACKET ADAPT K05 BTM LH
POCKET HINGE TOPRH
POCKET HINGE TOPLH
BRACKET ADAPT K05 BTM RH
BRACKET ADAPT K05 BTM LH
Top hinge pocket RH
(2)
K05 bottom adaptor bracket RH
(1)
Top hinge pocket LH
(2)
K05 bottom adaptor bracket LH
(1)
BRACKET ALCOVE TOP LH
BRACKET ALCOVE TOP RH
BRACKET ADAPT COL K05 RH
BRACKET ADAPT COL K05 LH
BRACKET ALCOVE TOP LH
BRACKET ALCOVE TOP RH
BRACKET ADAPT COL K05 RH
BRACKET ADAPT COL K05 LH
Top alcove bracket RH
(1)
K05 top adaptor bracket RH
(1)
Top alcove bracket LH
(1)
K05 top adaptor bracket LH
(1)
MODEL LEFT HINGE TO RIGHT HINGE KIT
RS61 CA 848184P
RS76 CA 848184P
MODEL RIGHT HINGE TO LEFT HINGE KIT
RS61 CA 848183P
RS76 CA 848183P
Not supplied and must be purchased separately. Available online at fisherpaykel.com.

13
PRODUCT DIMENSIONS MM
A Overall height 2134
B Overall width 603
C Overall depth* 610
*Excluding front door panel.
PRODUCT WEIGHT KG
Weight (with packaging) 162
Weight (without packaging) 142
PRODUCT DIMENSIONS — 610MM MODEL
C
B
A

14
CAVITY DIMENSIONS — 610MM MODEL
Aligns appliance flush with the cabinetry. Aligns appliance flush with the frame of cabinetry.
B
A
CAVITY DIMENSIONS MM
A Overall height 2134
B Overall width 610
C Minimum overall depth* 635
D Minimum cabinetry gap clearance from edge of door panels 3
E Minimum required finished return 102
* Assumes a door panel thickness of 3/4” (19mm).
C
D
E
A
B
C
D
E
A
B
FRAMELESS CABINETRY FRAMED CABINETRY

15
DOOR PANEL DIMENSIONS — 610MM MODEL
DIMENSIONS MM
A Height of top door panel 1254
B Height of bottom drawer panel 772
C Width of door/drawer panel 603
D Depth of door panel* min 16- max 25
DOOR PANEL WEIGHT KG
Weight of top door panel** max 15 1/2
Weight of bottom drawer panel** max 9 1/2
* Excluding door handle
** Maximum panel weight must not be exceeded
DIMENSIONS MM
A Height of top door panel 1254
B Height of bottom drawer panel 772
C Width of door/drawer panel 603
D Depth of door panel* 19
DOOR PANEL WEIGHT KG
Weight of top door panel 9
Weight of bottom drawer panel 6
*Excluding door handle
STAINLESS STEEL PANEL CUSTOM PANEL
B
C
A
D
B
C
A
D

16
CUSTOM DOOR PANEL INSTALL DIMENSIONS — 610MM MODEL
BOTTOM PANEL—REAR VIEW
TOP PANEL—REAR VIEW
Dimensions apply for the preparation and installation of Custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com.
z The thickness of the custom door panel can vary provided that the screws do not penetrate beyond the full depth of the door panel.
z Measurements of screw hole locations can vary depending on the height of toe kick 50–152mm.
2" (50mm)
301.6mm
203.2mm
50.8mm
603.2mm
32.6mm
38.m 127mm
507.8mm)
1092mm
50mm50mm
1254mm
Ø2mm REF
10x Pilot holes recommended
for bracket attachment.
(Do not penetrate front surface).
Ensure handle is mounted
65mm from edge to centre
of panel — this will avoid
interference with bracket.
11301.6mm
203.2mm
50.8mm
755.6mm
32.6mm
50mm
38.1m 88mm
508.4mm
588.4mm
771.5mm
Cutouts in the hanging bracket
are applicable for Fisher and
Paykel handles only.
Ø2mm REF
10x Pilot holes recommended
for bracket attachment.
(Do not penetrate front surface).
Iflocating a custom handle in
the shaded area shown above,
ensure handle screw headsare
countersunk into the back of the
door panel to avoid interference
with the hanging bracket.

17
A
C
WALL
DOOR CLEARANCE — 610MM MODEL
Insert hinge limiting pin
Before pushing the appliance into
the cabinetry, insert the supplied
hinge limiting pin into the borehole
of the top hinge. The hinge limiting
pin limits the door swing to 90°.
DIMENSIONS MM
A Width of door (90° open) measured from front of door 660
B Minimum door clearance* to adjacent wall** (115°—full internal access) 356
C Minimum door clearance* to adjacent wall** (90°—reduced internal access) 110
WALL
FULL INTERNAL ACCESS
A
B
115° DOOR OPENING 90° DOOR OPENING
LIMITED INTERNAL ACCESS

18
DIMENSIONS MM
A Maximum drawer extension when open* 400
B Maximum drawer extension when open** 461
* Excluding handle
** Including handle
DRAWER CLEARANCE — 610MM MODEL
A
B

19
TOE KICK PANEL (CA 25390)
DIMENSIONS MM
A Width of toe kick 606
B Height of toe kick 102
B
A
drawer panel
toe kick panel
DIMENSIONS MM
A Width of toe kick 606
B Height of toe kick min 51 - max 152
TOE KICK DIMENSIONS — 610MM MODEL
drawer panel
toe kick panel
B
A
For Custom door panel installation, a custom toe kick 2” –6” (50 – 152mm) can be
manufactured and fitted by cabinetmaker. The Custom door panel height needs to be adjusted
accordingly. Extra lower grilles are required for a 2” (50mm) toe kick installation.
Can be purchased separately through an authorised Fisher and Paykel dealer. Visit fisherpaykel.
com for more information.
STAINLESS STEEL TOE KICK PANEL CUSTOM PANEL TOE KICK PANEL

20
TOE KICK INSTALL OPTIONS
toe kick panel
For custom toe kick with 6"
(152mm) height.
Standard toe kick height is
4" (102mm) with Stainless steel
door panel.
Min 27/8" (73mm) – max
4" (102mm) toe kick depth
measured from rearof door
panel
For custom toe kick
with 2" (50mm) height
(extra lower grille attached).