Fisher & Paykel HP60 User manual

Installation Instructions
Contents of Packaging
Cooker hood (1)
Installation Instructions User
Guide Manual (1)
150mm ducting adapter with non return
flap
125mm ducting adapter (1)
13mm screw (2)
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
1

Product and Cabinetry Cutout Dimensions
Product Dimensions (mm) HP60 HP90
A. Overall height of product
(with ducting adapter)
350
(395)
315
(360)
B. Overall width of product 530 830
C. Overall depth of product 280 280
D. Thickness of flange 2 2
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
2

Product Dimensions (mm) HP60 HP90
E. Width of chassis 492 792
F. Depth of chassis 255 255
G. Height of side of chassis 120 120
H. Width of top surface of chassis 220 220
I. Length of angled surface of chassis 260 335
J. Distance from centre of ducting outlet to back of chassis 145 145
K. Distance from centre of ducting outlet to side of chassis 245 395
L. Diameter of ducting outlet 150 150
M. Distance between centre of lights 80 285
N. Distance from centre of light to back of product 70 115
Length of power cord 750 750
Cabinetry Cutout Dimensions (mm)
Overall width of cutout 500 800
Overall depth of cutout 260 260
O. Base of brackets/clips to bottom of chassis min. 15 – max. 40 min. 15 – max. 40
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
3

• Actual product dimensions may vary by ± 2mm.
• Please read the entire instructions before installing the cooker hood.
Height of Cooker Hood
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
4

Minimum Clearances mm
P. Height top of hob to base of product
*Electric hob (for induction hob see note below)
Gas hob
min. 600 – max. 750
min. 650 – max. 750
Cooker hood installation height above the hob is the user’s preference. This cooker hood must be installed between the
minimum and maximum height limits indicated in the table above. Installation at the minimum height limit will improve
the efficiency of capturing cooking odours, grease and smoke. Installation at the maximum height limit improves user
ergonomics by offering increased head room.
* Induction Cooking Considerations
• Induction hobs use energy efficient technology that only heats the contents of a cooking pot.
• Unlike gas or traditional electric hobs, the surrounding air does not get heated when using an induction hob. As
a result, cooker hood filters, splashbacks and surrounding cabinetry do not get warmed up, increasing the
likelihood of condensation on these cooler surfaces.
• Other factors like ambient temperature, humidity, natural ventilation of the room, size of the cookware and how
the induction hob is being used also influence condensation. For example, aggressive boiling on high hob heat
settings like PowerBoost increases the rate at which water is evaporated, increasing the likelihood of
condensation.
• It is important to understand that neither the cooker hood nor the induction hob are faulty as a result of this
phenomenon.
Condensation can be minimised by:
• Installing the cooker hood at the maximum height above the hob as specified in this user guide.
• Using the cooker hood on a lower speed setting when boiling.
• Using the induction hob on a lower heat setting when boiling.
• Switching the cooker hood on 5 minutes before cooking and letting it run for at least 5 minutes after cooking.
Refer to the ‘Operating instructions’ section on how to use the timer function.
Venting Options
Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are fulfilled.
The cooker hood can be installed to operate with the exhaust air ducted externally from the kitchen, or installed to
operate with the exhaust air recirculating within the kitchen.
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
5

Ducted Externally
For an externally ducted installation it is recommended that 150mm diameter, rigid or semi-rigid ducting is used. This will
require a 160mm (min) round hole in the ceiling or wall. Care should be taken to position the hole correctly.
For optimal efficiency, use rigid or semi-rigid ducting for reduced noise and increased airflow. Flexible ducting should
only be used as a last resort (ie in difficult installations) and if used, ensure that it is pulled tight.
Recirculation Mode
This cooker hood can be installed to recirculate within the kitchen where ducting externally is not a practical option. To
enable the product to operate in recirculation mode, please purchase carbon filters (refer to ‘Parts and Accessories’).
The carbon filters are required to remove odours.
A ducting hole is not required in the wall or ceiling if the cooker hood is installed to operate
in recirculation mode.
Installation
• This product is heavy and requires two persons for installation.
• Failure to install the screws or fixing device in accordance with these instructions may result in
electrical hazards.
The manufacturer is not liable for any damage caused by not following these instructions.
1. Prepare for installation.
Before installing your cooker hood:
• Please read the instructions carefully.
• Unpack the cooker hood and check that all functions are working.
• Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and
frequency at the installation site.
• The stainless steel and glass surfaces of the cooker hood are very easily damaged during installation if
grazed or knocked by tools. Please take care to protect the surfaces during installation.
• Protect the hob surface below with cardboard, or the like, to prevent damage occurring whilst the cooker
hood is being installed above.
2. Fit the 150mm ducting adapter with non return flap to the cooker hood using the screws supplied.
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
6

3. Provide an opening on the underside of the cupboard (see product and cabinetry cutout dimensions).
4. Remove the filters and face plate of the cooker hood.
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
7

5. Lift the cooker hood and fit through the opening of the cupboard till the spring loaded brackets/clips hold the
product in place.
6. Secure cooker hood while tightening the 4 brackets/clips.
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
8

7. Connect duct and plug cooker hood in.
https://producthelp.fisherpaykel.com/eu/Cook/Cooker_Hoods/Built-in_Integrated/HP90IHCB3/User_Guide_HP90IHCB3/03_in…
Updated: Sun, 02 Jan 2022 12:41:57 GMT
Powered by
9