Fisher-Price L0542 User manual

www.fisher-price.co.uk
L0542
IMPORTANT!
KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.

2
Prevent serious injury or death from falls
or sliding out:
• The child should at all times wear a safety
harness correctly fitted and adjusted. The tray
is not designed to hold the child in the chair.
• It is recommended that only children capable
of sitting upright unassisted use the high
chair in the upright position.
• Always keep child in view while in the
high chair.
• Never leave child unattended.
• Do not use the high chair unless all
components are correctly fitted and adjusted.
Prevent injury from burns: Do not place this
high chair near open fires or any hot surfaces.
WARNING
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
2
Consumer Information
IMPORTANT! Place the high chair on a level, stable surface
away from electrical flexes. Be sure to keep electrical flexes out
of child's reach.
•Please read these instructions before assembly and use of
this product.
•Adult assembly is required.
•Tool needed for assembly: Phillips screwdriver (not included).
•Product features and decorations may vary from photographs.
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.

3
Assembled Parts
2 Bases Footrest
2 Frames
Hinge Rod
2 Seat Bottom Tubes
Pad Seat Bottom
Seat Back
Base Tray
Food Tray Teether Toy
Note: Tighten or loosen all screws with a Phillips screw-
driver.
Do not over-tighten the screws.
Shown Actual Size
#8 x 1,9 cm Screws – 8 #10 x 2,2 cm Black Screw – 7

4
1
•Place the seat bottom face down on a flat surface.
•At an angle, fit the footrest on the seat bottom, as shown.
Assembly
Seat Bottom
Footrest
•Slide a seat bottom tube through each set of plastic rings on
the seat bottom.
2
Plastic Rings
Seat Bottom Tubes
Plastic Rings
IMPORTANT! Before assembly and each use, inspect this prod-
uct for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Mattel for replacement parts and instructions if needed.
Never substitute parts.
•Align the holes in the plastic rings and the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each plastic ring and into
the seat bottom tubes, as shown. Tighten the screws. This may
require extra force.
•Push the seat bottom tubes back and forth to be sure they are
secured to the seat bottom. If the seat bottom tubes move, you
have probably not fastened them properly. Remove the screws
and check to be sure the screw holes in the seat bottom tubes
and seat bottom plastic rings are aligned. Replace and tighten
the screws.
3

5
Assembly
4
•Insert two #10 x 2,2 cm black screws through the footrest
and into the seat bottom. Tighten the screws. This may require
extra force.
Insert Screws Here
5
Seat Back Pin
Slot
•Turn the seat bottom assembly upright.
•Fit the seat back pins into the slots in the top side of the seat
bottom assembly.
Seat Back Pin
Slot
6
Hinge Rod
•Turn the seat assembly face down.
•Insert the hinge rod through the hinge on the seat back and
seat bottom, as shown.
•Insert a #10 x 2,2 cm black screw into the hinge rod. Tighten
the screw.
•Set the seat assembly aside for Assembly step 9.
Hinge

6
7
Assembly
•Pull the frame leg out on each frame to open. Make sure it
"clicks" into place.
•Position a frame so that the decorated side is outward.
•Fit the end of a base into the back leg of a frame.
•Fit a screw retainer over the hole in the back leg, as shown.
•Insert a #10 x 2,2 cm black screw through the screw retainer
and back leg. Tighten the screw.
•Repeat this procedure to fasten the other frame back leg to the
other side of the base.
Hint: The #10 x 2,2 cm black screws may have been assembled to
the screw retainers.
Frame Decorated Side
Frame Back Legs
Base
Screw Retainers
Frame Leg
8
•While pressing the levers on the seat height adjusters, lift them
to position 4 on the frame front legs, as shown.
Seat Height Adjusters
Position 4
Press Lever
9
•Fit the seat assembly between the frames.
•Insert the seat bottom tubes into the sockets in each seat
height adjuster.
Hints:
•Be sure the seat height adjusters are in the same position
(position 4).
•You may need to push the frames apart slightly to fit the seat
bottom tubes into the seat height adjuster sockets.
Seat Assembly
Sockets
Seat Bottom Tubes

7
Assembly
10
Base
•Insert the frame front legs onto the remaining base.
•Fit a screw retainer over a hole in the front leg.
•Insert a #10 x 2,2 cm black screw through the screw retainer
and front leg. Tighten the screw.
•Repeat this procedure to secure the other end of the base with
the remaining screw retainer and #10 x 2,2 cm black screw.
Hint: The #10 x 2,2 cm black screws may have been assembled
to the screw retainers.
Screw Retainers
11
•Push each seat height adjuster to be sure they are completely on
the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each seat height adjuster and
the ends of the seat bottom tube. Tighten the screws. This may
require extra force.
Seat Bottom Tube Ends
PUSH PUSH

8
Assembly
12
•Push each seat height adjuster to be sure they are completely on
the seat bottom tubes.
•Insert a #8 x 1,9 cm screw through each seat height adjuster and
the ends of the seat bottom tube. Tighten the screws. This may
require extra force.
Seat Bottom Tube Ends
PRESS
13
•Squeeze the restraint release tabs together.
•Remove the ends of the restraint system from the peg.
PRESS
14
•Remove both shoulder straps from the seat back.
•Remove the crotch strap from the seat back.
Shoulder Straps
Crotch Strap
15
•Fit the pocket on the top of the pad onto the seat back.
Seat Height Adjusters

9
Assembly
16
Clips
•Fit the clips on the front edge of the pad onto the seat bottom.
•Hook the elastic loops on each side of the pad onto the tabs in
the seat back.
Shoulder
Straps Up
Crotch
Strap Down
Lowest Slot
Hint: Do not unbuckle the restraint system. It is easier to attach or
re-attach it to the product if it is buckled.
•Grasp the restraint system so that the shoulder straps are up
and the crotch strap is down.
•Insert the end of the crotch strap through the lowest slot in the
pad and the seat back.
•From behind the product, attach the end of the crotch strap to
the peg.
17

10
Assembly
Smaller Baby
•Insert the ends of the shoulder straps through the lower slots in
the pad.
•From behind the product, attach the ends of the shoulder straps
to the peg.
18
Shoulder
Straps
Larger Baby
•From the front of the product, insert the ends of the
shoulder straps through the upper slots in the pad and
seat back.
•From behind the product, attach the ends of the shoulder
straps to the peg.
19