Fisher-Price P6615 User manual

P6615
www.fisher-price.co.uk
IMPORTANT! KEEP
INSTRUCTIONS FOR
FUTURE REFERENCE.
WARNING

2
Important!
To prevent electric shock, do not immerse
in water; wipe clean with damp cloth.
Do not expose the product to rain or moisture.
Do not place objects filled with liquids on
or near the product.
DANGER
To prevent strangulation with power cord, never
place transmitter within reach of child.
WARNING
This product cannot replace responsible
adult supervision.
CAUTION

3
• For proper setup and use, please read these instructions.
• Please keep this instruction sheet for future reference, as it contains important information.
• Transmitter operates on AC current. Receiver operates on AC current (use enclosed AC adaptor) or
3,6V, 750 mAh NiMH rechargeable battery pack (included).
• Before first time use, charge the rechargeable battery pack for four hours.
• Adult assembly is required for wall mounting. Tools needed for assembly: electric drill, 7mm (.25 inch)
drill bit, hammer, Phillips screwdriver (tools not included).
• Adult setup is required.
• This product is not intended to be used as a medical monitor and its use should not replace
adult supervision.
• Test sound/video reception of receiver before first-time use and whenever you change location of
the transmitter.
• Adults Note: Periodically examine this product for damage to the cord, housing or other parts that may
result in the risk of fire, electric shock or injury. If the product is damaged, do not use it.
• Never use extension cords with the AC adaptor.
• Never use transmitter or receiver near water (i.e. bathtub, sink, wet basement, etc.).
• Always use transmitter and receiver where there is adequate ventilation. To prevent overheating,
keep the the transmitter, receiver and battery pack away from heat sources such as radiators, heat
registers, direct sunlight, stoves, amplifiers, fire, excessive heat or other appliances that produce heat.
• Fisher-Price®does not recommend the use of two monitors in one house.
• Always remember that you are using public airwaves when using your monitor. Conversations, even from
rooms near your transmitter, may broadcast to other nursery monitors, radios, cordless telephones or
scanners outside your home. To protect the privacy of your home, always turn off the transmitter when
not in use.
• Do not connect to more than the recommended number of power supplies.
• The AC adaptor is not a toy.
• Disconnect the AC adaptor from the receiver before cleaning.
• If this product begins to operate erratically, you may need to reset the electronics. Turn the transmitter
power/volume dial off and then back on; press the receiver main power/menu button to turn power off
and press again to turn power back on.
• The receiver unit may generate a tone when there is radio interference present in the location of
operation whilst monitoring. The unit will resume to normal when the interference stops.
• Carrier Frequency: 2.4 Ghz
• Product features and decoration may vary from photos.
Important!
Hereby Mattel declares that the product is in compliance with the essential requirements and other
relevant provisions of European Council Directives 99/5/EC, 89/336/EEC. Suitable for the U.K.
0125 !

4
9
10
12
11
4
14
Features
Receiver Transmitter
6
1
4
7
3
13
2
5
8
AC Adaptor/Charger Transmitter Tabletop Stand

5
1Main Power/Menu Button – Press to turn receiver main power ON; press again for the main
menu; press and hold for approximately five seconds to turn main power OFF.
2Power L.E.D. – Turns on when receiver power is ON.
3Menu Navigation/Volume Control Button – Press up, down or side arrows to scroll through menu
options. When the menu is not on the screen, press the side arrows to adjust volume.
4Speaker
5Video Screen
6Video Screen On/Off Button – Press to turn the video screen on; press again to turn it off.
7Sound Lights – Shows you baby's sounds.
8DC Input Jack – Insert the AC adaptor/charger pin to use AC power/charge the battery.
9Camera Lens
10 Power/Volume Dial – Rotate to turn transmitter power ON and adjust volume to a comfortable
level for baby.
11 Microphone
12 Music, Sounds and Night Light Buttons
Music – Choose from 5 lullaby songs.
Sounds – Play nature sounds.
Night Light – Turn on night light for baby.
13 Power L.E.D. – Turns on when transmitter power is ON.
14 Night Light – Lights room with a soft glow.
Features

6
Fasteners Shown Actual Size
Wall Mount Parts
Wall Mount Bracket Cord Wrap Base Stand
Wall Anchor – 4
#8 x 5 cm (2") Screw – 4

7
Charging the Battery
(Inside the Receiver)
DC Input Jack
IMPORTANT! Fully charge the receiver (with battery pack inside) for four hours before first-time use.
Use only the included AC adaptor charger! Do not use any other adaptor charger.
• Fit the AC adaptor charger pin into the DC input jack on the receiver.
• Plug the AC adaptor charger into a standard wall outlet.
Notes: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”. Use the AC
adaptor charger only in a wall outlet. Do not plug the AC adaptor charger into a ceiling outlet.
• If you are monitoring baby while charging the battery pack, you will see the charging icon on the
video screen.

8
Testing Sound/Video Reception
• Place the transmitter in the room where you intend to use it.
• Point the transmitter toward the area you will be monitoring. Adjust the camera angle by rotating the top
portion of the transmitter up or down.
• Turn the power/volume dial ON.
• Turn on a radio.
Power Dial
Test transmitter transmission and receiver reception before installing the wall mount bracket
and cord wrap (if used) and each time you change location of use.
Radio

9
Testing Sound/Video Reception
• Place the receiver in the room where you intend to use it.
• Press the main power/menu select button on the front of the receiver to turn power ON.
• Adjust the receiver location for best reception.
• When sound is picked up by the receiver, the sound lights will turn on.
- One or two lights indicate quieter sounds.
- Three or more lights indicate louder sounds.
• If you cannot see an image on the receiver screen, adjust the transmitter location or camera angle.
Sound Lights
Main Power/Menu Select
Button

10 11
Transmitter Wall Mount Installation
To prevent strangulation with power cord, never
place transmitter within reach of child.
WARNING
IMPORTANT! Test the reception of the monitor before installing the wall mount bracket and cord wrap.
Use the assistance of one adult to hold the transmitter against the wall in the spot you want to install it.
Then, test the reception of the receiver in several locations around your house. Please refer to the Testing
Sound/Video Reception section of these instructions.

10 11
• To provide the greatest viewing range, we recommend you install the wall mount bracket at least
1,8 meters (6 feet) from the floor.
• Make sure the camera lens does not have an obstructed view of your baby. Adjust the camera up or down.
• Allow adequate ventilation of the transmitter when mounted. Do not mount the transmitter above heating
vents or other heat producing sources. Do not mount the transmitter where it can receive direct sunlight.
• Install the wall mount bracket on a flat section of the wall. The wall mount bracket cannot be
corner mounted.
• Make sure the AC adaptor will reach a wall outlet before installing the wall mount bracket. To prevent
entanglement, never use an extension cord.
Transmitter Wall Mount Installation
1,8 Meters
(6 Feet)

12 13
Transmitter Wall Mount Installation
• Using a 7mm (.25 inch) drill bit, drill one hole through each pencil mark you made on the wall.
• Hold the wall mount bracket against the wall in the location you want to install it. Make sure the wall
mount bracket is straight.
• Using a pencil, make a mark on the wall inside the upper hole and lower slot on the wall mount bracket.
• Set the wall mount bracket aside.
Wall Mount Bracket
1
2

12 13
• Fit a wall anchor into each of the drilled holes.
• Tap each wall anchor lightly with a hammer until the ends of each wall anchor are even with the surface
of the wall.
• Align the holes on the wall mount bracket with the wall anchors.
• Insert two screws into the holes in the wall mount bracket and tighten with a Phillips screwdriver. Do not
over-tighten.
Wall Anchor
Transmitter Wall Mount Installation
3
4

14 15
• Position the cord wrap against the wall, so that it is centred below the wall mount bracket and as close
to the floor as possible.
• Move the cord wrap approximately 1,3 cm (.5 inch) towards the wall outlet.
• Using a pencil, make a mark on the wall inside both holes in the cord wrap.
• Set the cord wrap aside.
Transmitter Wall Mount Installation
Cord Wrap
Wall Mount Bracket
5

14 15
• Using a 7mm (.25 inch) drill bit, drill one hole through each pencil mark you made on the wall.
• Place a wall anchor into each of the drilled holes.
• Tap each wall anchor lightly with hammer until the ends of each wall anchor are even with the surface of
the wall.
Wall Anchor
Transmitter Wall Mount Installation
7
6

16 17
Transmitter Wall Mount Installation
• Align the holes on the cord wrap with the wall anchors.
• Insert two screws into the holes in the cord wrap and tighten with a Phillips screwdriver.
Do not over-tighten.
Cord Wrap
• Put the transmitter into the base stand.
• Fit the transmitter cord into the slot in the base stand and the wall mount bracket.
• Slide the stand into the slot on the wall mount bracket.
Wall Mount Bracket
Transmitter
Slot
Base Stand
8
9
Slot

16 17
10
Transmitter Wall Mount Installation
IMPORTANT! Make sure the cord is taught between the transmitter and cord wrap. Excess cord can form
loops or extend into the crib and present a strangulation hazard.
• Extend the transmitter cord straight down the wall to the cord wrap.
• Wrap the transmitter cord around the cord wrap, leaving just enough to reach the wall outlet. Make sure
there is no slack in the transmitter cord.
• Thread the transmitter cord through the groove in the front of the cord wrap. Make sure the transmitter
cord is fully inserted in the groove.
• Plug the transmitter cord into the wall outlet.
Groove
Cord Wrap
1,8 Meters
(6 Feet)

18
Setup/On Screen Displays
Main Menu
• First, turn both transmitter and receiver
power ON. Then press the main power/
menu select button on the receiver to
see the main menu.
• Press the up, down or side arrows to
scroll through menu options. As you
scroll, the menu choices highlight and
blink on the screen.
• Press the main power/menu select
to choose:
Music
Sounds
Night Light
Voice Activated Screen
Contrast/Brightness
Turn Main Menu Off
Hint: The main menu turns off if you
do not scroll through choices or make
a selection within approximately
15 seconds. Simply press the main
power/menu select button again to
return to the main menu.
• You can turn on music or sounds and a
night light for baby. You cannot turn on
both music and sounds.
MAIN POWER/
MENU SELECT

19
Setup/On Screen Displays
Sounds
Turn sounds off
Select nature sounds
Select heartbeat sounds
Return to previous menu
Exit menu
If you turn sounds ON one of the
sound icons or will appear
on the bottom of the screen.
Music
Turn music off
Turn music on and cycle through
all five songs
Select song number one
Select song number two
Select song number three
Select song number four
Select song number five
Return to previous menu
Exit menu
If you turn the music ON the music
icons will appear on the bottom of
the screen.

20
Setup/On Screen Displays
Night Light
Turn night light off
Turn night light on
Return to previous menu
Exit menu
If you turn the night light on the night
light icon will appear on the bottom
of the screen.
Voice Activated
(For Nighttime Use)
Video screen turns on for 30 seconds
and then turns off. When baby
makes noise, video screen automati-
cally turns back on. It will remain on
and turn off after 30 seconds from
the last sound detected. You can also
press any button on the receiver to
turn video back on.
Video screen does not turn on when
baby makes noise. Press the video
screen on/off button on the top of the
receiver to turn the video screen on
and off.
Return to previous menu
Exit menu