Fisher-Price 73528 User manual

D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Rock, Roll ‘n Ride Trike
Rock, Roll ‘n Ride TrikeTM
Instructions
Model Number: 73528
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Age: 11/2years - 5 years.
Weight Limit: 50 lbs. (23 kg).
Tools needed for assembly: Phillips Screwdriver, Hammer and Scrap Block of Wood (all not included).
If you have any questions about this product, or are missing a part, please call
us toll-free at 1-800-432-KIDS, rather than return this product to the store.

WARNING
•Adult supervision is required.
•Never use near steps, sloped driveways,
hills, roadways, alleys, swimming pools or
other bodies of water.
•Always wear shoes or sneakers.
•Never allow more than one (1) rider.
Please read these instructions carefully and identify all
parts before assembly. Refer to the parts page for identifica-
tion.Call Fisher-Price®Consumer Relations, toll-free at
1-800-432-KIDS, 8 AM - 6 PM EST Monday through
Friday. Hearing-impaired consumers using TTY/TDD
equipment, please call 1-800-382-7470.
Or, write to:
Fisher-Price®Consumer Relations,
636 Girard Avenue
East Aurora, NewYork 14052.
For other countries outside the United States:
Canada:call 1-800-567-7724, or write to: Mattel Canada Inc., 6155
Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone [phone].
Australia:Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag
#870, Richmond, Victoria 3121 Australia. Consumer Advisory Service
1300 135 312.
New Zealand:16-18 William Pickering Drive, Albany 1331, Auckland.
Consumer Information
Fasteners
Fasteners
All SHOWN ACTUAL SIZE
#8 x 3" Screw – 1
Cap Nut – 2*
Consumer Information
2
2
#10 x 3/4" Screw - 11
#8 x 3/4" Screw - 13
*Note: For your convenience, an
extra cap nut is included.

Parts
Parts
Fisher-Price
Seat Pin
Seat
Handlebar
Handle Pin
Frame Cover
Handle Top
Handle Bottom
Base
2 Base/Handle Covers
Fork
Front Wheel
2 Fork Covers
4 Pedal Axle Covers
Pedal Axle 2 Pedals
Straight Axle 2 Rear Wheels
2 Cap Nuts
2 Wheel Caps
Frame
Footrest
Note: The base/handle assembly
can be attached to the trike in
either the Ride-on Rocker (page 9)
or Learn to Pedal (page 10) mode.
3
3

Assembly
Assembly
•Please save all packaging material until assembly is complete to ensure that no parts are discarded.
•Please wipe each part with a clean, dry, cloth before assembling this product.
This product contains small parts in its
unassembled state. Adult assembly is required.
•Place a cap nut on a scrap block of wood.
•Place one end of the straight axle into the cap nut.
•Tap the cap nut with a hammer. Make sure the cap nut is
securely attached to the straight axle.
1
Straight Axle
Cap Nut
2
Straight Axle
Rear Wheel
Spoke Side Down
3
•Turn the frame upside down.
•Insert the straight axle assembly through the holes in the
rear of the frame.
•Fit the wheel cap into the center of the wheel.Tap the
wheel cap with a hammer to secure it to the wheel.
Frame
Wheel
Cap Hole
Hole
Rear Wheel
Straight Axle
•Slide a rear wheel (spoke side down) onto the straight axle.
Bottom View
4
4
Scrap Block
of Wood
CAUTION

Assembly
Assembly
4
•Turn the frame on its side with the exposed end of the
straight axle up.
•Place the assembled rear wheel on the scrap block
of wood.
•Slide the other rear wheel (spoke side up) onto the end of
the straight axle.
•Place a cap nut on the end of the straight axle.
•Tap the cap nut with a hammer. Gently pull the rear
wheel up to be sure the cap nut is securely attached
to the straight axle.
Cap Nut
Straight Axle
Rear Wheel
Spoke Side Up
Assembled
Rear Wheel
•Fit two pedal axle covers onto the pedal axle metal tabs.
Make sure the metal tabs fit into the slot in each pedal
axle cover.
6Pedal Axle Cover
Pedal Axle
Metal Tab
Slot Pedal Axle Cover
•While holding the pedal axle covers on the pedal axle,
insert the pedal axle into the hole in the center of the
front wheel.
7Pedal Axle Covers
Pedal Axle
Front Wheel Hole
•Push the pedal axle covers into the center of the front
wheel until they are flush with the surface of the
front wheel.
8Pedal Axle Covers
•Fit the wheel cap into the center of the wheel.Tap the
wheel cap with a hammer to secure it to the wheel.
•Set the frame assembly aside.
5Wheel Cap
5
5
Scrap Block
of Wood

Assembly
Assembly
• Push the pedal axle covers into the center of the front wheel
until they are flush with the surface of the front wheel.
10
Pedal Axle Covers
6
6
• Place a scrap block of wood under the front wheel assembly.
•Slide a pedal on the pedal axle.
•Tap the pedal with a hammer until it is secure.
•Repeat this procedure to attach the other pedal to the
other end of the pedal axle.
•Pull on the pedals to be sure they are secure on the
pedal axle.
11
Pedal
Pedal Axle
Front Wheel
Assembly
•Place the front wheel assembly between the fork arms so
that the pedal axle fits into the groove at the bottom of
each fork arm.
•Place a fork cover over the pedal axle on one fork arm.
•Insert two #10 x 3/4" screws into the fork cover and tighten
with a Phillips screwdriver. Do not over-tighten.
•Repeat this procedure to attach the other fork cover to the
other fork arm, using the #10 x 3/4" screws.
12
Fork Cover Fork Arms
Groove
Pedal Axle
Scrap Block
of Wood
Front Wheel Assembly
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052, U.S.A.
©2002 Mattel, Inc. All Rights Reserved.
®and
TM designate U.S. trademarks of Mattel, Inc.
Printed in Mexico
73528a-0920
•Turn the front wheel assembly over.
•Insert a pedal axle cover onto the top of the pedal axle
and into the hole in the center of the front wheel.
•Insert the remaining pedal axle cover below the pedal axle
and into the hole in the center of the front wheel.
9Pedal Axle Cover
Pedal Axle Cover
Pedal Axle

•Insert the knobbed end of the
footrest up through the opening in
the underside, center of the frame .
•Rotate the footrest 1/4turn .
•Slide the footrest toward the handle-
bar as far as it will go until the top of the footrest is
positioned over the opening’s rectangular cut-out.
•Lower the knobbed end of the footrest into the rectangular
cut-out in the frame .
Assembly
Assembly
•Turn the frame upright.
•Insert the fork post up through
the hole in the frame neck. Make sure the fork is posi-
tioned so that the fork covers face the rear wheels.
•Place the handlebar over the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
•Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post so that part of the screw (about
3/4")
is still visible
.
•Then, tighten the screw with a Phillips screwdriver.
Do not over-tighten.
13
Handlebar
Frame Neck
Fork Covers
Fork Post
14
Frame Opening
Footrest
Knobbed End
Footrest
Top View
Knobbed End
7
7
• Place the frame cover over the frame opening. Make
sure the holes in the frame cover align with the holes
on the frame.
•Insert three #10 x 3/4" screws into the frame cover and tight-
en with a Phillips screwdriver. Do not over-tighten.
15
Frame Cover
•Place the seat on the seat mount.
•Adjust the seat for your child’s comfort by aligning the hole
in the seat with one of the seat mount adjustment holes.
16
Seat Mount Adjustment Holes
Seat
Seat Mount
2
➥
➥
3
➥
1
2
3
3/4"
1
FIRST, insert the screw
so that 3/4" is visible.
THEN, tighten the screw
with a Phillips screwdriver.

Assembly
Assembly
•While pushing down on the seat, insert the seat pin
through the hole in the seat and into a seat mount
adjustment hole.
17
Seat Pin
•Insert 13 - #8 x 3/4" screws through the handle top, base
and into the handle bottom.Tighten the screws with a
Phillips screwdriver. Do not over-tighten.
19
•Place the base/handle assembly on a flat surface so that
the wheel retainers are upright.
•Fit the trike onto the base/handle assembly so that the
rear frame rests in the grooves in the base and the front
wheel fits between the wheel retainers in the base/handle.
20
Wheel
Retainers
Base/Handle
Grooves
•Fit the handle top and bottom to the end of the base, as
shown.
18
Handle Top Base
8
8
Handle Bottom

Ride-on Rocker
Ride-on Rocker
•Insert the base/handle pin through one wheel retainer, a
hole in the front wheel and into the other wheel retainer.
•Push the handle pin to “snap” it into place.Pull on the
handle pin to be sure it is secure.
Wheel Retainer
Front Wheel
Wheel Retainer
Base/Handle Pin
9
9
IMPORTANT! Be sure to adjust the seat in the most forward
position for Ride-on Rocker mode.
Label Application
Label Application
Handle
Place Center
of Label Here
Center of Label
Assembly
Assembly
21
Base/Handle
Flared End
Trike
Handle
Cover
•Position the base/handle covers so that the flared end
faces the front of the trike.
•Fit the base/handle covers onto the trike rear frame near
the rear wheels.
•Insert two #10 x
3/4"
screws through each base/handle
cover and into the base/handle.Tighten the screws with a
Phillips screwdriver. Do not over-tighten.
Assembly is now complete.
•Before applying the label, wipe the surface of the
handle with a clean, dry cloth to remove any dust or oils.
•Remove the backing from the label.
•First, position the center of the label on the handle,
as shown.Then, smooth each end of the label outward
to attach it to the handle.
•For best results, avoid repositioning a label once it has
been applied to the handle.

3
2
Base/Handle
•Insert the handle pin through one side of the base/handle,
through the holes in the back of the frame and out through
the hole in the other side of the base/handle. Make sure
the handle pin “snaps” into place.
•Pull on the handle pin to be sure it is secure.
Base/Handle
•Rotate the base/handle to the upright position.
Handle Pin
Learn to Pedal Trike
Learn to Pedal Trike
10
10
Learn to Pedal Trike
Learn to Pedal Trike
•If you are converting from the ride-on rocker mode, remove
the handle pin from the wheel retainers and front wheel.
1
Wheel Retainer Front Wheel Wheel Retainer
Handle Pin