Fisher-Price Barbie Free Spirit Trike 72639 User manual

Free Spirit Trike
Please keep these instructions for future reference.
Adult assembly is required.
Tools needed for assembly: Hammer, Phillips Screwdriver, Scrap Block of Wood (all not included).
If you have any questions about this product, or are missing a part, please call us toll-free
at 1-800-432-KIDS, rather than return this product to the store.
Age: 2 - 5 years.
Weight Limit: 55 lbs.
Instructions
Model Number: 72639
72639b-0920.qrk 12/6/00 9:26 AM Page 1

#8 x 3" Screw – 1
#8 x 3/4" Screw – 4
ALL SHOWN ACTUAL SIZE
Lock Washer – 2
Washer – 2
Cap Nut – 2
WARNING
• Adult supervision is required.
• Never use near steps, sloped driveways,
hills, roadways, alleys, swimming pools
or other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
2
4 Pedal Hubs
2 Pedals
2 Lock Washers
Pedal Axle
2 Fork Covers
Front Wheel
Fork
Frame
Handlebar
Seat
Straight Axle
2 Washers
2 Rear Wheels
2 Hubcaps
2 Cap Nuts
NOTE: Some parts shown are assembled
to both sides of the trike.
IMPORTANT!
• Please save all packaging material until assembly
is complete to ensure that no parts are discarded.
• If you are missing a part, please call us toll-free at
1-800-432-KIDS, rather than return this product to
the store.
• Please wipe each part with a clean, dry cloth
before assembly.
Parts
Parts
72639b-0920.qrk 12/6/00 9:26 AM Page 2

• Place a cap nut on a scrap block of wood.
• Place one end of the straight axle into the cap nut.
• Tap the end of the straight axle with a hammer. Make sure
the cap nut is securely attached to the straight axle.
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
• Slide a washer onto the straight axle.
Cap Nut
Straight Axle
Rear Wheel
Indented
Side Down
Straight Axle
Washer
3
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
Hole Hole
Frame
Straight Axle
Hubcap
1
3
2
Bottom View
Scrap Block
of Wood
Assembly
Assembly
CAUTION
This product contains small parts in its
unassembled state. Adult assembly is required.
72639b-0920.qrk 12/6/00 9:26 AM Page 3

• Fit two pedal hubs onto the pedal axle tabs. Make sure the
tabs fit into the slot in each pedal hub.
Pedal Hub
Pedal Hub
Pedal Axle
Tab
Tab
Slot
• While holding the pedal hubs on the pedal axle, insert the
pedal axle through the hole in the center of the front wheel.
Hole
Pedal Axle
Pedal Hubs
Front Wheel
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
Pedal Hubs
5
6
7
4
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the assembled rear wheel on the scrap block of wood.
• Slide a washer onto the straight axle.
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
• Slide a hubcap (peg side down) onto the straight axle.
• Fit a cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Gently pull the rear wheel
up to be sure the cap nut is securely attached to the
straight axle.
• Set the frame assembly aside.
Cap Nut
Indented
Side Up
Assembled Rear
Wheel
Straight Axle
Rear Wheel
Washer
Hubcap
Frame
4
Bottom View
Scrap Block
of Wood
Assembly
Assembly
72639b-0920.qrk 12/6/00 9:26 AM Page 4

5
Pedal Hubs
Pedal Hub
Pedal Hub Pedal Axle
• Turn the front wheel assembly over.
• Insert a pedal hub onto the top of the pedal axle and into
the hole in the center of the front wheel.
• Insert the remaining pedal hub below the pedal axle and
into the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
• Insert a lock washer into the slot in the pedal. Make sure
the raised tabs on the lock washer are facing the
“closed” or outside end of the pedal.
• Insert the other lock washer into the other pedal.
Lock Washer
Raised Tabs
Slot
Closed (Outside) End
of Pedal
8
9
10
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x 3/4" screws through the fork cover and into
the fork arm. Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• Repeat this procedure to attach the other fork cover
to the other fork arm.
Fork Arms
Pedal Axle
Groove
Fork Cover
#8 x 3/4" Screw – 4
SHOWN ACTUAL SIZE
• Place a scrap block of wood under the front wheel assembly.
• Fit a pedal on the pedal axle.
• With the lock washer centered over the pedal axle end, tap
the pedal with a hammer until it is secure.
• Repeat this procedure to attach the other pedal to the other
end of the pedal axle.
Lock Washer
(Inside)
Front Wheel
Assembly
Front Wheel Assembly
Scrap Block
of Wood
Pedal Axle
Pedal
11
12
Assembly
Assembly
72639b-0920.qrk 12/6/00 9:26 AM Page 5

6
• Turn the frame upright.
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
• Place the handlebar over the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
Hint: You may need to rotate the handlebar to align the holes.
• Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post. Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
Handlebar
Frame Neck
Fork Post
Fork Cover
#8 x 3" Screw – 1
SHOWN ACTUAL SIZE
• At an angle, insert one peg on the back of the seat into the
hole in the top rear of the frame.
• Insert and “snap” the other peg on the back of the seat
into the other hole in the top rear of the frame.
One-time assembly is now complete.
Seat
Holes
Pegs
13 14
Rear of Trike
Assembly
Assembly
72639b-0920.qrk 12/6/00 9:26 AM Page 6

7
Proper label application will help to keep the labels looking their best!
• Wash your hands before applying the labels.
• Make sure the areas where the labels will be applied are clean and dry. Wipe your vehicle with a clean, soft, dry cloth to
remove any dust or oils.
• For best results, avoid applying a label more than once.
• Apply the labels as shown in the illustrations below.
• After applying a label, rub the label firmly with a cloth to make sure the label is adhered to your vehicle.
Right Side
Left Side
7
6
2
4
1
8
3
6
5
Label Decoration
Label Decoration
72639b-0920.qrk 12/6/00 9:27 AM Page 7

• Check plastic parts regularly and if broken or cracked, dispose of them properly.
• Check all fasteners regularly to be sure they are tight. If the fasteners are not tight, tighten them as necessary.
• To clean the trike, use a mild soap and water solution and a clean cloth. Rinse clean with water to remove soap residue.
If you have any questions about this product:
In Canada, call 1-800-567-7724, or write to: Mattel Canada Inc, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
In Great Britain, telephone [phone].
In Australia, Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812
(valid only in Australia).
Questions? We'd like to hear from you!
Call Consumer Relations, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired
consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to: Consumer Relations, 636 Girard Avenue,
East Aurora, New York 14052.
Maintenance
Maintenance
Consumer Information
Consumer Information
Fisher-Price, Inc., a subsidiary of Mattel, Inc.
East Aurora, New York 14052, U.S.A.
© 2000 Mattel, Inc. All Rights Reserved. Printed in Mexico
® and ™ designate U.S. trademarks of Mattel, Inc. 72639b-0920
BARBIE is a U. S. trademark of Mattel, Inc.
72639b-0920.qrk 12/6/00 9:27 AM Page 8