Fisher-Price 73528 User manual

1
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Age: 1½ years - 5 years.
Weight Limit: 50 lbs. (23 kg).
Tools needed for assembly: Phillips Screwdriver,
Hammer and Scrap Block of Wood (all not included).
73528
www.fisher-price.com

2
WARNING
To avoid serious injury:
• Adult supervision is required.
• Never use near cars and other motor vehicles,
near streets, steps, sloped driveways, hills,
roadways, alleys, swimming pool areas or
other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one (1) rider.
Fasteners
All SHOWN ACTUAL SIZE
#8 x 3" Screw – 1
Cap Nut – 1*
Consumer Information
#10 x 3/4" Screw - 11
#8 x 3/4" Screw - 13
*Note: For your convenience, an
extra cap nut is included.
Note: Tighten and loosen the screws with a Phillips
screwdriver. Do not over-tighten the screws.

3
Parts
Seat Pin
Seat
Handlebar
Handle Pin
Frame Cover
Handle Top
Handle Bottom
Base
2 Base/Handle Covers
Fork
Front Wheel
Assembly
2 Fork Covers
4 Pedal Axle Covers
Straight Axle 2 Rear Wheels
Cap Nuts
2 Wheel Caps
Frame
Footrest
Note: The base/handle assembly
can be attached to the trike in
either the Ride-on Rocker (page 9)
or Learn to Pedal (page 10) mode.
Parts not shown: Assembly
Tool and Label.

4
Assembly
• Please save all packaging material until assembly is
complete to ensure that no parts are discarded.
• Please wipe each part with a clean, dry, cloth before
assembling this product.
This product contains small parts in its
unassembled state. Adult assembly is required.
1
Straight Axle
Rear Wheel
Spoke Side Down
• Turn the frame upside down.
• Insert the straight axle assembly through the holes in the
rear of the frame.
• Fit the wheel cap into the center of the wheel. Tap the
wheel cap with a hammer to secure it to the wheel.
Frame
Wheel
Cap Hole
Hole
Rear Wheel
Straight Axle
• Slide a rear wheel (spoke side down) onto the straight axle.
Bottom View
CAUTION
2

5
Assembly
• Fit the wheel cap into the center of the wheel. Tap the
wheel cap with a hammer to secure it to the wheel.
• Set the frame assembly aside.
4
Wheel Cap
3
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the assembled rear wheel on the scrap block
of wood.
• Slide the other rear wheel (spoke side up) onto the end
of the straight axle.
• Place a cap nut on the end of the straight axle.
• Place the assembly tool over the cap nut and tap it with
a hammer. Gently pull the rear wheel up to be sure
the cap nut is securely attached to the straight axle.
Cap Nut
Straight Axle
Rear Wheel
Spoke Side Up
Assembled
Rear Wheel
Assembly Tool
Scrap Block
of Wood
• Fit two pedal axle covers onto the pedal axle metal tabs.
Make sure the metal tabs fit into the slot in each pedal
axle cover.
• While holding the pedal axle covers on the pedal axle,
insert the pedal axle into the hole in the center of the
front wheel.
• Push the pedal axle covers into the center of the front
wheel until they are flush with the surface of the
front wheel.
• Repeat this procedure with the other two pedal axle
covers on the other side of the front wheel assembly.
5
Pedal Axle
Cover
Pedal Axle
Cover
Metal Tab
Slot
Pedal Axle

6
Assembly
• Place the front wheel assembly between the fork arms
so that the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #10 x ¾ " screws into the fork cover
and tighten.
• Repeat this procedure to attach the other fork cover to
the other fork arm, using the #10 x ¾ " screws.
6
Fork Cover Fork Arms
Groove
Pedal Axle
Front Wheel Assembly
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052, U.S.A.
©2008 Mattel, Inc. All Rights Reserved. ® and TM designate U.S. trademarks of Mattel, Inc.
• Turn the frame upright.
• Insert the fork post up through
the hole in the frame neck. Make sure the fork is
positioned so that the fork covers face the rear wheels.
• Place the handlebar over the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
• Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post so that part of the screw (about ¾")
is still visible . Tighten the screw.
7
Handlebar
Frame Neck
Fork Covers
Fork Post
PRINTED IN MEXICO 73528c-0920
FIRST, insert the screw
so that ¾" is visible.
THEN, tighten the screw.
¾"

7
• Insert the knobbed end of the foot-
rest up through the opening in the
underside, center of the frame .
• Rotate the footrest ¼ turn .
• Slide the footrest toward the
handlebar as far as it will go until
the top of the footrest is
positioned over the opening’s rectangular cut-out.
• Lower the knobbed end of the footrest into the rectangular
cut-out in the frame .
Assembly
8
Frame Opening
Footrest
Knobbed End
Footrest
Top View
Knobbed End
• Place the frame cover over the frame opening. Make
sure the holes in the frame cover align with the holes
on the frame.
• Insert three #10 x ¾" screws into the frame cover
and tighten.
9
Frame Cover
• Place the seat on the seat mount.
• Adjust the seat for your child’s comfort by aligning the hole
in the seat with one of the seat mount adjustment holes.
10
Seat Mount Adjustment Holes
Seat
Seat Mount
2
➥
➥
3
➥
1
2
3
1

8
Assembly
• While pushing down on the seat, insert the seat pin
through the hole in the seat and into a seat mount
adjustment hole.
11
Seat Pin
• Insert 13 - #8 x ¾ " screws into the handle top
and tighten.
13
• Place the base/handle assembly on a flat surface so that
the wheel retainers are upright.
• Fit the trike onto the base/handle assembly so that the
rear frame rests in the grooves in the base and the front
wheel fits between the wheel retainers in the base/handle.
14
Wheel
Retainers
Base/Handle
Grooves
• Fit the handle top and bottom to the end of the base,
as shown.
12
Handle Top
Base
Handle Bottom

9
Ride-on Rocker
• Insert the base/handle pin through one wheel retainer,
a hole in the front wheel and into the other wheel retainer.
• Push the handle pin to “snap” it into place. Pull on the
handle pin to be sure it is secure.
Wheel Retainer
Front Wheel
Wheel Retainer
Base/Handle Pin
IMPORTANT! Be sure to adjust the seat in the most
forward position for Ride-on Rocker mode.
Label Application
Handle
Place Center
of Label Here
Center of Label
Assembly
15
Base/Handle
Flared End
Handle
Cover
Trike
• Position the base/handle covers so that the flared end
faces the front of the trike.
• Fit the base/handle covers onto the trike rear frame near
the rear wheels.
• Insert two #10 x ¾" screws into each base/handle cover
and tighten.
Assembly is now complete.
• Before applying the label, wipe the surface of the
handle with a clean, dry cloth to remove any dust or oils.
• Remove the backing from the label.
• First, position the center of the label on the handle,
as shown. Then, smooth each end of the label outward
to attach it to the handle.
• For best results, avoid repositioning a label once it has
been applied to the handle.

10
3
2
Base/Handle
• Insert the handle pin through one side of the base/handle,
through the holes in the back of the frame and out through
the hole in the other side of the base/handle. Make sure
the handle pin “snaps” into place.
• Pull on the handle pin to be sure it is secure.
Base/Handle
• Rotate the base/handle to the upright position.
Handle Pin
Learn to Pedal Trike
Learn to Pedal Trike
• If you are converting from the ride-on rocker mode, remove
the handle pin from the wheel retainers and front wheel.
1Wheel Retainer
Front Wheel
Wheel Retainer
Handle Pin