Fisher-Price BDD52 User manual

1
To prevent entanglement,
keep hair away from wheels.
CAUTION
Press and
hold the GO
button and
they’re off!
BDD52
fisher-price.com
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four AA (LR6) alkaline batteries (not included) for vehicle operation.
Adult assembly is required. Tool required for battery installation:
Phillips screwdriver (not included).
The vehicles are not recommended for use on loose dirt or wet surfaces.
Wipe this toy with a clean cloth dampened with
a mild soap and water solution. Do not immerse any part of this toy.
This toy has no consumer serviceable parts. Do not take the vehicles apart.

2
FCC Statement (United States Only)
This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Note: Changes or modifications not
expressly approved by the manufacturer
responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Consumer Information
ICES-003
This Class B digital apparatus complies
with Canadian ICES-003. Operation is
subject to the following two conditions:
(1) this device may not cause harmful
interference and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
NMB-003
Cet appareil numérique de la classe
B est conforme à la norme NMB-003
du Canada. L’utilisation de ce dispositif
est autorisée seulement aux conditions
suivantes : (1) il ne doit pas produire
de brouillage et (2) l’utilisateur du
dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même
si ce brouillage est susceptible de
compromettre le fonctionnement
du dispositif.
CO
N
SU
MER
ASS
I
S
T
A
N
C
E
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
©2014 Mattel. All Rights Reserved.
PRINTED IN CHINA BDD52a-0920

3
Battery Installation
• Locate the battery compartment door
on the bottom of each vehicle.
• Loosen the screw in each battery
compartment door with a Phillips
screwdriver and remove the door.
• Insert two AA (LR6) alkaline batteries
into each vehicle.
• Replace the battery compartment
door and tighten each screw. Do not
over-tighten.
• If a vehicle begins to operate
erratically (stops after bumping into
an object or it does not turn off)
you may need to reset electronics.
Remove the batteries for about
3 minutes and then reinstall them.
• When sounds or motions from a
vehicle become faint or stop, it’s time
for an adult to change the batteries.
For longer life, use alkaline batteries.
Battery Safety
Information
In exceptional circumstances, batteries
may leak fluids that can cause
a chemical burn injury or ruin your
product. To avoid battery leakage:
• Do not mix old and new batteries
or batteries of different types:
alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods
of non-use. Always remove exhausted
batteries from the product. Dispose of
batteries safely. Do not dispose of this
product in a fire. The batteries inside
may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or
equivalent type, as recommended.
• Do not charge non-rechargeable
batteries.
• Remove rechargeable batteries from
the product before charging.
• If removable, rechargeable batteries
are used, they are only to be charged
under adult supervision.
• Protect the environment by not
disposing of this product with
household waste (2002/96/EC).
Check your local authority for
recycling advice and facilities.
1,5V x 4
AA (LR6)

4 5
Lower Track Assembled Parts
“Snap” both tall
trestles, labeled 4, and
a short trestle, labeled
8, to the track piece
labeled 4 - 5 - 12.
“Snap” a short
trestle, labeled 8,
to the track piece
labeled 5 - 6.
d
Each track piece has a number on the bottom. Simply match
the numbers and fit the pieces together! For best performance,
we suggest assembling on a hard, flat surface.
“Snap” a short
trestle, labeled 8,
to the track piece
labeled 2 - 3.

6 7
Each track piece has a number on the bottom.
Simply match the numbers and fit the pieces together!
Upper Track Assembled Parts
“Snap” the wide
based trestle, labeled
10, to the track piece
labeled 9 - 11.

8 9
Decoration
1
1
4
6
6
2
2
7
8
10
11
12
13
13
9
5
3
1
1
6
6
2
2
7
8
10
11
13
13
9
3
Before applying the labels, wipe the surface with a clean, dry cloth to remove any dust or oils.
Place the labels exactly as shown in the illustration and avoid repositioning the labels.
After applying a label, rub it firmly with a clean dry cloth, starting at the center, to remove any air bubbles.

10
Race to Win!
• Lift the starting gates on the track.
• Set the vehicles on the arrows behind
the starting line.
• Shake each vehicle to start the
“engine” and the sound effects.
Hint: For maximum distance, shake
the vehicle 7 or 8 times. Shaking more
than this does not increase the distance
each will travel.
• Press and hold the GO button and
they’re off!
• When a vehicle stops, pick it up,
shake it and set it down again to
rejoin the race.
Hint: Vehicles can also be used on any
smooth, flat surface.
• Lift the track lever to lift the upper
track and send a vehicle to the
lower track.
• Slide the lever to send the opponent
into Spinout Alley™!
Hint: To reset the the spinout platform,
push it back up the track and “click”
into place.
1
2
3
4Reset Spinout Platform