Fisher-Price M5644 User manual

www.fisher-price.com
Please keep this instruction sheet for future reference, as it contains
important information.
Requires three “AA” (LR06) alkaline batteries (not included).
Adult assembly is required.
Tool required for battery installation: Phillips screwdriver (not included).
M5644

Assembled Parts
2 Track Pieces Barn
Station Ramp
House Crossing
Gate
Bushes

Battery Installation
• Locate the battery compartment on the bottom of the toy.
• Loosen the screw in the battery compartment door with a Phillips screwdriver. Remove the
battery compartment door.
• Insert three “AA” (LR06) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screw with a Phillips screwdriver.
• When sounds from this toy become faint or stop, it’s time for an adult to change the batteries.
1.5V x 3
“AA (LR06)”
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities (Europe only).
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury
or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-
zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from
the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries
inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.

Assembly
• Fit the track pieces together and “snap” in place.
Track Pieces
1
1
Barn
• Attach the barn, station and house to the stops on the track.
Hint: Each building will only fit in one place. If it does not fit, try again in a different spot.
Station House
1
3
Crossing Gate
• Fit the crossing gate onto the ramp.
1
5
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. M5644pr-0920
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA

All Aboard!
Power Switch
• Slide the power switch on the bottom of the track to the on position .
• Drive the train around the track to hear fun sounds and music at every stop!
• Press or twist the buttons on each building for a surprise!
Bushes
• Attach the bushes to the track and “snap” in place.
1
2
Assembly
Ramp
• Connect the ramp to the track.
1
4

Consumer Information
Care
• Wipe the toy with a clean cloth dampened with a mild soap and water solution.
• Do not immerse the toy.
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.