Fisher-Price P6831 User manual

www.fisher-price.com
P6831
R0322

Consumer Information
• Please keep this instruction sheet for future reference,
as it contains important information.
• Adult assembly is required.
• Tools required for assembly: Phillips Screwdriver,
Hammer and Scrap Block of Wood (not included).
• Age: 2-5 years
• Weight limit: 55 lbs (25 kg).
• Please save all packaging material until assembly is
complete to ensure that no parts are discarded.
• Please wipe each part with a clean, dry cloth
before assembly.
WARNING
CAUTION
To avoid serious injury:
• Adult supervision is required.
•
Never use near cars and other motor
vehicles, near streets, steps, sloped
driveways, hills, roadways, alleys, swimming
pool areas or other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
This product contains small parts
in its unassembled state.
Adult assembly is required.
2
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO P6831pr-0920

Seat
2 Fork Covers
Front Wheel
Assembly
Fork
Handlebar Back
Upper Steering Ring
Lower
Steering Ring
Rear Axle
Seat Pin
2 Rear
Wheel Hubs 2 Rear
Wheel Caps
2 Pedal Blocks
#8 x 2¼" Screw - 1 #6 x 1/2" Screw - 2
Note: Some parts shown are assembled to both sides of the trike.
*We’ve included one extra .354" cap nut for your convenience.
Note: Tighten and loosen the screws with a Phillips screwdriver. Do not over-tighten the screws.
4 Pedal Hubs
#8 x ¾" Screw - 6
2 Rear
Wheels
Part not shown: Label Sheet
ALL FASTENERS SHOWN ACTUAL SIZE
Handlebar Front
.354" Cap Nut - 2*
.354"
Parts
3
Frame

Assembly
Rear Axle Assembly
Frame
• Slide a rear wheel hub, rounded side up, onto the
rear axle.
• Slide a rear wheel, indented side down, onto the rear axle.
• Turn the frame upside down.
• Insert the rear axle assembly through the holes in the rear
of the frame.
• Turn the assembly upright.
• Slide a rear wheel, rounded side rst, onto the end of the
rear axle.
• Slide a rear wheel hub, pointed end rst, onto the end of
the rear axle.
Rear Axle
Rear Wheel Hub
(Pointed End First)
Rear Wheel
(Flat Side First)
Rear Axle
Rear
Wheel
(Indented
Side Down)
4
• Fit a cap nut on the end of the rear axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel to be sure the cap nut is securely attached to
the rear axle.
Hint: You may need the help of another adult to hold the
other end of the rear axle in place.
.354"
Rear Wheel Hub
(Flat Side Down)
1
2
4
3
Bottom View

Assembly
• Fit the tabs on a rear wheel cap into the slots in the rear
wheel hub. Push to "snap" the rear wheel cap in place.
• Repeat this procedure to attach the other rear wheel cap
to the other wheel hub.
• Fit two pedal hubs onto the pedal axle tabs. Make sure
the tabs t into the slot in each pedal hub.
• While holding the pedal hubs on the pedal axle, insert the
pedal axle into the hole in the center of the front wheel.
• Press the pedal hubs into the center of the front wheel
until they are ush with the surface of the front wheel.
• Repeat this procedure on the other side with the other
two pedal hubs.
• Fit the lower steering ring onto the frame, as shown.
Rear Wheel Hub
Rear Wheel Cap
Pedal Hub
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle ts into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x ¾" screws into the fork cover and tighten.
• Repeat this procedure to attach the other fork cover to the
other fork arm.
Fork Arms
Pedal Axle
Groove
Fork Cover
Front Wheel
Assembly
Pedal Hub
Pedal Axle Tab
5
Lower Steering Ring
5
6
7
8

Assembly
Fork Post
Lower
Steering Ring
Fork Cover
• While holding the lower steering ring in place, insert the
fork post up through the hole in the neck of the frame.
Make sure the fork is positioned so that the fork covers
face the rear wheels.
• Fit the upper steering ring onto the frame, as shown.
REAR OF TRIKE
• Fit the handlebar front to the fork post, as shown.
• Fit the handlebar back to the fork post and handlebar front.
Hold them together rmly.
• Insert the remaining #8 x ¾" screws through the outer
holes in the handlebar back and tighten.
Handlebar Front
¾" Screw
¾" Screw
Handlebar Back
Fork Post
6
Upper
Steering Ring
• Insert the #8 x 2¼" screw through the center hole in the
handlebar back and tighten.
2¼" Screw
911
12
10

Assembly
• Fit the seat onto the frame.
• Insert the seat pin into the holes in the frame.
Hint: The seat is adjustable to your child's size. Have your
child sit on the seat and check the foot pedal distance.
Adjust the seat up or down for your child's comfort.
Seat Pin
• Fit the pedal blocks onto each pedal for smaller riders.
Insert a #6 x 1/2" screw into hole in each pedal block
and tighten.
• Remove the pedal blocks for bigger riders and store for
future use.
1/2" Screw
Seat
13
14
7

Consumer Information
Care
• Periodically, check the plastic parts and if broken or cracked,
dispose of them properly.
• Periodically, check all fasteners regularly to be sure they
are tight. If the fasteners are not tight, tighten them
as necessary.
• To clean, use a mild soap and water solution and a clean
cloth. Rinse clean with water to remove soap residue.
IMPORTANT! It is a good practice to start training children
very young regarding the importance of helmet use. When
children are older and riding bicycles and faster vehicles,
it is important that they use a helmet each and every time
they ride. For this reason, even while riding a tricycle, it is
a good idea to familiarize your child with helmet use,
so that it becomes a habit for life. Choose a helmet that
complies with requirements of the applicable certifying
agency for bicycle helmets.
8