Fisher-Price M9974 User manual

Please keep this instruction sheet for future reference,
as it contains important information.
Requires three “AA” batteries (included).
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
M9974
www.fisher-price.com
Actual product may appear different
than the product shown.
Doll sold separately.

This package contains small parts in its
unassembled state. Adult assembly is required.
Take extra care during unpacking and assembly.
CAUTION
Assembly
• Fit the body onto the base, as shown.
1
• Fit the basket into the slot on the base.
2
Assembled Parts
2
#8 x 1/2” Screws – 12
Shown Actual Size
Note: Tighten and loosen all
screws with a Phillips screwdriver.
Do not over-tighten screws.
Handlebar - 2 Pieces
Seat
Basket
Body
Base
Body
Basket
Base
Slot

Assembly
• First, insert the long handlebar
through the hole in the pony head A.
Hint: You may need to turn the long handlebar to fit it into
the hole.
• Then, insert the short handlebar through the hole on the
other side of the pony head B.
• While holding the handlebars in place, carefully tip the pony
so that the short handlebar faces up.
• Insert a screw into the hole in the short handlebar
and tighten.
3
• Turn the assembly upright.
• Fit the seat onto the assembly.
• Insert two screws into the holes on each side of the seat
and tighten.
3
4
Bottom View
5
• While holding the body and base together, carefully tip the
assembly over.
• Insert seven screws into the holes in the base and tighten.
Base
Seat
Long
Handlebar
Short
Handlebar
A
B

Battery Replacement
4
• Protect the environment by not disposing of this
product with household waste (2002/96/EC). Check
your local authority for recycling advice and facilities.
Battery Safety Information
For best performance, we recommend that you replace the
batteries that came with this toy with three, new “AA” (LR6)
alkaline batteries.
• Locate the battery compartment side of the pony.
• Loosen the screws in the battery compartment door with
a Phillips screwdriver. Remove the battery compartment door.
• Insert three “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door and tighten the screws.
• If toy begins to operate erratically, you may need to reset the
electronics. Slide the power/volume switch on the toy off and
then back on.
• When sounds become faint or stop, it’s time for an adult to
change the batteries!
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your toy. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the toy. Dispose of
batteries safely. Do not dispose of the product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging.
• If removable, rechargeable batteries are used, they are only
to be charged under adult supervision.
1.5V x 3
“AA” (LR6)

• Slide the power/volume switch on the toy to on with low volume ; on with high volume or off .
• Press the button on the pony's head for musical tunes.
Roll-Along with Music
Power/Volume
Switch
5
Press

Wipe with a clean cloth dampened with a mild soap and water
solution. Do not immerse.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. M9974pr-0920
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA
Consumer Information
FCC Statement (United States Only)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device
must accept any interference received, including interference
that may cause undesired operation.