Fisher-Price 79029 User manual

w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Model Number: 79029
Please read these instructions before assembly and use of this product.
Keep this instruction sheet for future reference, as it contains important information.
With seat in place, for use by children who have the neck control to hold their head upright.
To prevent falls, never use with an active child who may be able to climb out of the seat.
Adult assembly is required.
This product requires three “C” (LR14) alkaline batteries (not included).
Tool needed for battery installation: Phillips Screwdriver (not included).
Step & Play Piano
Product features may vary from picture above.

2
To prevent serious injury or death:
•When seat is in place, use only for
a child who is able to hold head
upright unassisted and who is not
able to walk.
•Never leave child unattended.
Always keep child in view while
in product.
•Never use near steps or pools,
hot surfaces or areas that may be
hazardous to a child. Product may
move during use.
•To avoid tip over, place product on
a flat, level surface.
WARNING
Occasionally a consumer may experience a problem with
one of our products. If this should happen, please call us
toll-free, rather than return this product to the store.
Usually, we can solve the problem over the telephone
or send you replacement parts.
Please call Fisher-Price® Consumer Relations, toll-free at
1-800-432-5437, 8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or, write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
For other countries outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont
Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone [phone].
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond,Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre,
Harbour City, Tsimshatsui, HK, China.
Consumer Information
Warning

3
Parts
Pad
2 Legs with
▲ Detail
Base
Seat Ring
4 Rollers
Seat Base
Upper Rail with Leg
Upper Rail
Trumpet
Bell
Mirror
Tray
Maraca
Tambourine
Leg with
● Detail
444444
3 3 3 3 3 3
111111
222222
222
1
1
1
333
444
Note: The legs and base sockets have been coded with tape. Do not remove the tape
until you have completed assembly of this product.

222
4
Assembly
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.
2
•Locate the leg with tape on it.
•Locate the matching tape covering the socket in the base.
•Align the tab on the leg with the slot in the base socket.
•Insert and “snap” the leg into the base socket.
4 4 4 4 4 4
3 3 3 3 3 3
2 2 2 2 2 2
111111
1
1
1
1
•Locate the upper rail with leg and tape on it.
•Remove the cardboard attached to the wire connector. Throw
the cardboard away.
•Pull the wire connector out from the hole in the bottom of
the leg.
2
Tape
Base Socket
Wire Connector
Tape
2
Upper Rail with Leg
Cardboard
Leg
•Position the upper rail with leg so that the leg with tape is
over the base socket with matching tape.
•Insert and “snap” the leg with tape into the socket with
matching tape.
•Now, firmly push the upper rail above the leg with tape on
it. Make sure you hear a “snap”.
•Firmly push the upper rail above the leg with tape on it.
Make sure you hear a “snap”.
•Pull up on the upper rail to be sure it is secure.
2
2
2
4 4 4 4 4 4
222
1
1
1
3 3 3 3 3 3
2 2 2 2 2 2
3
Upper Rail
with Leg
Base Socket
PUSH
PUSH
Tape
2
1
1
1
222
333
444
4 4 4 4 4 4
3 3 3 3 3 3
4
Base Socket
Base Socket
•Locate the legs with tape on them.
•Locate the matching tape covering the sockets in the base.
•Align the tabs on the legs with the slots in the base sockets.
•Insert and “snap” the legs into the base sockets.
4
3
Tape
4
Tape
3

5
Assembly
•Fit the upper rail onto the legs, as shown.
•Push down firmly above each leg until, you hear the upper rail
“snap” into place on each end.
•Pull up on the upper rail to be sure it is secure.
Note: Remove the tape on the legs and around the base
sockets.Throw the tape away.
1
1
1
222
333
444
5
•Fit the “T” end of the strap on the trumpet through the slot in
the upper rail. Pull the trumpet to be sure it is secure in the
upper rail.
6
Upper Rail
Trumpet
Upper
Rail Slot
Hint: You may want to use the end of a slotted screwdriver to push
the “T” end of the strap through the slot.
PUSH
PUSH
“T” End
•At an angle, fit the single tab on the bell into the slot in the
upper rail.
•Now, push and “snap” the other two tabs on the bell into the
slots in the upper rail.
•Position the mirror so that it is toward the inside of the product.
•Insert and “snap” the tabs on each end of the mirror into the
matching slots in the upper rail.
7
8
Bell Upper
Rail
Slot
Mirror
Slots
PUSH

6
Assembly
•Fit the tray underneath the mirror, into the upper rail,
as shown.
•Insert and “snap” the ends of the maraca and tambourine into
the holes in each end of the upper rail with keyboard.
10
9
Tray
Maraca
Tambourine
• Locate the seat lock buttons on the underside of each
upper rail.
•Fit the groove on each side of the seat base onto the tracks on
the upper rails.
12
Seat
Lock
Button
Track
Seat Base
Groove
•Turn the seat base upside down on a flat surface.
•Insert and “snap” a roller into each clip on the edge of the seat
base, as shown.
•Repeat this procedure to assemble the remaining two rollers to
the other side of the seat base.
11
Seat Base
Roller
Roller
Clip
Clip

7
•Position the seat ring so that the
inside (ribbed side) is up and the
star marking is toward you.
•Fit the red slots on the pad to the
seat ring pegs on either side of the
star marking, as shown.
Assembly
•While pushing a seat lock button on one of the upper rails,
slide the seat base over it.
•Now, push the seat lock button on the other upper rail and
slide the seat base over it.
•Push the seat base so that it is positioned in the center of the
product. You should hear a “snap” on each side.
13
Seat Ring
Ribbed Side
Red Slot Red Slot
Marking
14
Pegs
Marking
PUSH
•Pull the pad through the seat ring and wrap the pad
around the outside of the seat ring.
Seat Ring
Seat Ring
Pad
Pad
15

8
•Fit the other six slots on the seat pad to the corresponding
pegs on the seat ring.
•Tuck the seat pad behind all four rollers.
Assembly
16
Peg 2
Peg 3 Peg 4
Peg 5
Peg 6
Roller
Roller
Roller Roller
Peg 1
•Insert and “snap” the seat with pad into the hole in the
seat base.
•Pull up on the seat to be sure it is secure.
17
Seat with
Pad
Hole
in Seat Base
•Tip the end of the product up and locate the wire connectors.
•Fit the connectors together. If they will not go together easily,
do not force them together. Turn one or the other connectors
over, and try again!
One-time assembly is now complete.
18
Connectors

9
Installation
•Locate the battery compartment door under the upper rail
with keyboard.
•Loosen the screw in the battery compartment door with a
Phillips screwdriver. Remove the battery compartment door.
•Insert three “C” (LR14) alkaline batteries, as indicated inside
the battery compartment.
•Replace the battery compartment door and tighten the screw
with a Phillips screwdriver. Do not over-tighten.
Battery
Compartment
Door
Batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
•Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
•Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of bat-
teries safely. Do not dispose of batteries in a fire.
The batteries may explode or leak.
•Never short-circuit the battery terminals.
•Use only batteries of the same or equivalent type,
as recommended.
•Do not charge non-rechargeable batteries.
•Remove rechargeable batteries from the product
before charging.
•If removable, rechargeable batteries are used, they are only to
be charged under adult supervision.
SHOWN ACTUAL SIZE
1.5V x 3
“C” (LR14)
Hint: We recommend the use of alkaline batteries for
longer battery life.
Battery Safety InformationBattery Installation

10
Seat Height Adjustment
•Place baby in the seat. Check the distance between your
baby’s feet and the keyboard base.
•Remove baby from the seat.
•Join the buckles to shorten (upper position) or lengthen
(lower position) the seat pad.
Buckles
Upper
Position
Lower
Position
Remove Seat
•When baby outgrows using the seat, you can remove it from
the upper rails.
•Push the seat lock buttons under each upper rail (you will
have to do this one at a time), and slide the seat base off of
the upper rails.
•Store the seat in a safe location for future use.
Set-Up & Use
To prevent serious injury or death:
•When seat is in place, use only for a child who is able to hold head upright
unassisted and who is not able to walk.
•Never leave child unattended. Always keep child in view while in product.
•Never use near steps or pools, hot surfaces or areas that may be hazardous to a
child. Product may move during use.
•To avoid tip over, place product on a flat, level surface.
WARNING
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never
substitute parts.
PUSH PUSH