Courtyard Creations KVS945Y 299-9911 User manual

KVS945Y (299-9911)
Usethecorrectboltsasindicated.Donottightenanyoftheboltsuntilthesectionalandottomanarecompletelyassembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC No. when contacting the service center.
SERVICE CENTER TOLL FREE NO
TEL: [phone]
FAX: [phone]
PAGE 1 OF 4
PARTS LIST
1
1
1
124
19
2
2
KVS945Y-CS02-7
KVS945Y-CS01-3
KVS945Y-CS03-5
KVS945Y-CS02-6
KVS945Y-CS03-4
COURTYARD CREATIONS INC.
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
1
2
13
4
5
6
8
11
12
13
14
15
16
17
18
19
20
21
22
23
24
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
!
!
!
!
!
1
1
1
1
2
1
7
11
KVS945Y-CS01-2
KVS945Y-CS04-H
KVS945Y-CS04-H
62KVS945YQ102
62KVS945YQ103
KVS945Y-CS08-5
CARLING WICKER SECTIONAL SOFA
17C40A0717001YX
17FA05040301-YX
17KAA0101----Y4
17KAB1101----Y4
F-3
10
9
24
1
2
3
1
1
1
17C40A0712001YX
18000C23001
61K945YX50001BA
61K945YY00001BA
61K945YB00001BA
17C40A0710001YX
61K945YX00001BA
61K945YY50001BA
BOLT M6*50
BOLT M6*35
BOLT M6*30
NUT WRENCH 10 &13MM
HEX. KEY WRENCH 4MM
LEFT ARM A
BACK ASSEMBLY A
RIGHT ARM B
SEAT ASSEMBLY B
SEAT ASSEMBLY A
BACK ASSEMBLY B
LEG A
LEG B
SUPPORT A
SUPPORT B
SUPPORT C
PLASTIC NUT M6*P1.0
WASHER d6.5*D13*1.0
BACK CUSHION
ARM CUSHION
LEFT SEAT CUSHION
RIGHT SEAT CUSHION
OTTOMAN CUSHION
217C40A0705001YX BOLT M6*15

50
#15 BOLT M6*50
PAGE 2 OF 4
FIGURE 1
Step 2:
Fasten the support A (#9) to the seat assembly A (#1)
by using bolt (#12). Fasten the support A (#9) to the
left arm A (#2) by using bolt (#13), washer (#16), and
plastic nut (#17). Keep the bolts loose. See Figure 2.
Step 3:
Insert the back assembly A (#3) into the left arm A (#2).
Fasten the back assembly A (#3) to the left arm A (#2)
by using bolts (#15), washers (#16), and plastic nuts (#17).
Keep the bolts loose. See Figure 3.
Step 4:
Place the right arm B (#5) onto a non-abrasive surface,
such as a carpet, with its underside facing upwards.
Fasten the seat assembly B (#4) to the right arm B (#5)
by using bolts (#15), washers (#16), and plastic nuts (#17).
Keep the bolts loose. See Figure 4.
FIGURE 2
FIGURE 3 FIGURE 4
1
2
12
13
16
17
15 3
2
25
4
16
3
17
50
#15 BOLT M6*50
15
16
17
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
Step 1:
Place the left arm A (#2) onto a non-abrasive surface,
such as a carpet, with its underside facing upwards.
Fasten the seat assembly A (#1) to the left arm A (#2)
by using bolts (#15), washers (#16), and plastic nuts (#17).
Keep the bolts loose. See Figure 1.
15
1
2
16
17
50
#15 BOLT M6*50
F-3
9
30
15
#13 BOLT M6*30
#12 BOLT M6*15

35
#14 BOLT M6*35
13
16
17
PAGE 3 OF 4
FIGURE 7 FIGURE 8
Step 5:
Fasten the support B (#10) to the seat assembly B (#4)
by using bolts (#13 and #14), washers (#16), and plastic
nuts (#17). See Figure 5.
Step 7:
Fasten the support C (#11) to the seat assembly B (#4)
and the seat assembly A (#1) by using bolts (#15),
washers (#16), and plastic nuts (#17). See Figure 7.
Step 8:
Fasten supports (#9 and #11) to the seat assembly A
(#1), the seat assembly B (#4), the back
assembly A (#3),
and the back assembly B (#6) by using bolts (#14 and #15),
washers (#16), and plastic nuts (#17). Fasten the support
A (#9) to the seat assembly A (#1) by using bolt (#12).
See Figure 8.
Step 6:
Insert the back assembly B (#6) into the right arm B (#5).
Fasten the back assembly B (#6) to the support B (#10)
by using bolts (#13), washers (#16), and plastic nuts (#17).
Fasten the back assembly B (#6) to the seat assembly B
(#4) and the right arm B (#5) by using bolts (#15),
washers (#16), and plastic nuts (#17). See Figure 6.
FIGURE 5 FIGURE 6
4
4
5
6
5
6
13
14
10 10
10
6
16
17
1617
35
#14 BOLT M6*35
15
16
17
30 #13 BOLT M6*30 30 #13 BOLT M6*30
50
#15 BOLT M6*50
15
11
4
1
16
17
15
16
17
15
16
17
3
3
6
6
4
1
50
#15 BOLT M6*50
F-3
11
9
11
14
12
16
17
15
#12 BOLT M6*15
1
49
11
50
#15 BOLT M6*50

FIGURE 9 FIGURE 10
30 #13 BOLT M6*30
13
7
8
20
23
24
22
21 21
20 20
8
Warranty
•This product is covered by Courtyard Creations Inc.'s one–year limited warranty.
•Proof of purchase (dated register receipt) is required for warranty claims.
•It remains the customer’s responsibility for freight and packing charges to and from the service center.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
For further assistance,
please visit us at
[email protected]
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL OF THE PARTS,MAKING SURE THAT
YOUHAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANYDIFFICULTYDURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
PAGE 4 OF 4
F-3
Step 9:
Fasten the leg A (#7) to legs B (#8) by using bolts (#13).
Make sure that all of the bolts have been tightened
completely. See Figure 9.
Step 10:
Turn to its upright position. Position all of the sections
together as illustrated, to complete your set. Place
cushions (#20, #21, #22, #23, and #24) onto the frame.
See Figure 10.
Cleaning and Maintenance
• Wash frame, wicker, and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use
bleach, acid, or other solvents on the frame, wicker, or fabric parts.
• The cushions may be washed on the surface only by using mild soap and water or a commercial foaming
upholstery cleaner if necessary. If washed, rinse well and hang to dry. Do not machine wash or dry.
• We recommend the use of furniture covers when not in use.
• Inspect and tighten all of the bolts and fasteners on a regular basis to ensure the proper performance and safety
of your sectional and ottoman.
• In order to prolong the life and beauty of your sectional and ottoman, we recommend that they be stored in a dry
and protected area during off season periods.