Flash LED PAR 64 18x12 RGBWA+UV FLAT User manual

LED PAR 64 18x12
RGBWA+UV FLAT
User Manual
Art No F7100345
EAN [5905358808450]
SERIES: DJ

CONTENTS
INTRODUCTION 3
SAFETY INFORMATION 3
PRODUCT INFORMATION 4
INSTALLATION 4
CONNECTION 5
DMX CHART 8
WARNING! Use clamp to rig the xture.
WARNING! When clamping the xture to a truss or other structure at
any other angle than with the yoke hanging vercally downwards, use two
clamps of half-coupler type. Do not use any type of clamp that does not
completely encircle the structure when fastened.
WARNING! Posion or shade the bar so that the front lens will not be
exposed to sunlight or any other strong light source from any angle - even
for a few seconds. See Figure 1. The LED PAR lens can focused the sun’s
rays, creang a potenal re hazard and causing damage.
IMPORTANT! Do not point strong light output from other xtures at the
LED PAR, as intense illuminaon can damaged the display.
Figure 1.
2

INTRODUCTION
SAFETY INFORMATION
THANK YOU FOR PURCHASING LED PAR 64. FOR SAFETY RE-
ASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CARE-
FULLY READ THE INSTRUCTIONS.
Please keep this User Manual
for future consultaon. If you sell
the xture to another user, be sure
that they also receive this instruc-
on booklet.
Unpack and check carefully the-
re is no transportaon damage be-
fore using the xture.
Before operang, ensure that
the voltage and frequency of po-
wer supply match the power
requirements of the xture.
It’s important to ground the
yellow/green conductor to earth
in order to avoid electric shock.
Disconnect main power before
servicing and maintenance.
Use safety chain when xes this
xture. Don’t handle the xture by
taking its head only, but always by
taking its base.
Maximum ambient temperature
is: 40°C Don’t operate it where the
temperature is higher than this.
In the event of serious ope-
rating problem, stop using the
fixture immediately. Never try
to repair the fixture by your-
self.
Repairs carried out by unskil-
led people can lead to damage
or malfunction. Please contact
the nearest authorized techni-
cal assistance center. Always
use the same type spare parts.
Do not connect the device
to any dimmer pack.
Do not touch any wire during
operation and there might be a
hazard of electric shock.
To prevent or reduce the risk
of electrical shock or fire, do
not expose the fixture to rain
or moisture.
The housing must be repla-
ced if they are visibly damaged.
Do not look directly at the li-
ght spot while the fixture is on.
3

PRODUCT INFORMATION
INSTALATION
Light Source:
18x12W RGBWA+UV LED’s
Power consumpon: 120W
Power supply voltage:
100-240V, 50/60Hz AC
LED macro colors
Operang modes: DMX512,
Manual, Auto, Sound-controlled,
Master/Slave, Sound acve,
DMX channel mode
6 /1 0 A / 10 B
IP Rang: IP20
Housing made: Aluminium
Cooling: Acve
AC IN/OUT: PowerCon
3-Pin XLR DMX Input/Output
Net Weight: 2.2 kg
Gross weight: 2.6 kg
Net Dimensions:
H(20)xW(20)xD(8) cm
Pack Size:
H(23)xW(26)xD(26) cm
The unit should be mounted via
its screw holes on the bracket.
Always ensure that the unit is
firmly fixed to avoid vibration
and slipping while operating.
Always ensure that the structu-
re to which you are attaching
the unit is secure and is able
to support a weight of 10 ti-
mes of the unit’s weight. Also
always use a safety cable that
can hold 12 times of the we-
ight of the unit when installing
the fixture. The equipment must
be fixed by professionals. And it
must be fixed at a place where is
out of the touch of people and
has no one pass by or under it.
The fixture may be installed in
any orientation, but if installed
horizontally with a downward
4
beam-angle, water can poten-
tially pool in the fan wells. Under
normal operation the moisture
will evaporate. However, in loca-
tions with high rainfall, you may
wish to fabricate a rain shield
above the fixture, or modify the
position and orientation of the
fixture to minimize pooling.
Two quarter-turn brackets are
supplied with the fixtre if it is
to be flown above the ground.
Rig the fixture to a support truss
or structure using the supplied
brackets and suitable clamps.
Fasten a safety cable between
the support structure and the
attachment point on the fixture.
The safety cable must be able to
bear at least 10 times the weight
of the fixture.

CONNECTION
The device is equipped with the following interfaces:
1. DMX (in/out): XLR 3(5)-pin socket
2. Power (in/out): powerCON socket
The connecon is performed using cable with
XLR-female -> XLR-Male plugs.
1
3
22
SHIELD
SIGNAL (+)
SIGNAL (-)
3
1
FEMALE
XLR
MALE
XLR
1
SHIELD
SIGNAL (+)
SIGNAL (-)
FEMALE
XLR
MALE
XLR
2
3
4
5
1
2
3
45
CAUTION! At the last xture, the
DMX signal has to be terminated
with a terminator. Solder a 120Ω
resistor between signal (-) and si-
gnal (+) into a XLR plug and plug
it in the DMX output of the last
xture.
3-PIN XLR
5-PIN XLR
5
The package includes:
❶ - LED PAR (1 pc)
❷ - Power cable type
powerCON (1 pc)
❸ - User Manual (1 pc)
❹ - Mounting bracket (1 pc)
❶
❷
❸
❹
User
Manual

Using lamp, the change rate of power voltage should be within ±10%,
if the voltage is too high, it will shorten the light’s life; if it’s not enough,
the lamp will be dark. Please restart it aer turning o light for 20 mi-
nutes unl full-cooling. Frequent switching will reduce the life span of
lamps and bulbs; intermient using will improve the life of bulbs and
lamps.
Input Voltage Amperage Frequency Total Power
100-240[V] AC 0,78[A] 50/60[Hz] 120[W]
Voltage Specicaon.
6
Control Menu
DMX
Controller DMX 512 DMX 512 120
Ω
Diagram of connecon of devices by DMX cable.
IMPORTANT! The maximum number of devices connected
in series via power cable is 10 pcs.
The connecon is performed using power cable with powerCON con-
nector (included). The device must be operated by qualied personnel.
CAUTION! In the case of cable damage do not aempt to repair. Repla-
cement or repair can be made only on the manufacturer or by a person
with appropriate permissions
MENU
UP DOWN ENTER
DISPLAY

7
Manual Menu
D 001 CH 001-512
Channel Ch 6 / CH 10 A / CH 10 B
AU (Jump Changing) 01-99 Speed
FA 01-99 Speed
PU 01-99 Speed
SO 01- 99 Sensivity
Red 001-255
Green 001-255
Blue 001-255
White 001-255
Amber 001-255
UV 001-255
ST (Strobo) 01 - 99 Slow > Fast
Reno ------

8
CH
No 6CH 10 A CH 10 B CH
1Red Dimmer Dimmer
2Green Red Strobo
3Blue Green Macrocolor
000-050 Empty
051-100 Jump changing programm
101-150 Gradual changing prog.
151-200 Pulsive changing prog.
201-255 Sound acvated on
4 White Blue Speed macro color
Speed from slow>fast, music ac-
vated, sensivity from slow >fast
5Amber White Red
6 UV Amber Green
7UV Blue
8Strobo White
9Macrocolor Amber
000-050 Empty
051-100 Jump changing programm
101-150 Gradual changing prog.
151-200 Pulsive changing prog.
201-255 Sound acvated on
10 UV
DMX CHART

9

10

11

FLASH-BUTRYM Sp.j.
Skarbimierzyce 18 · 72-002 Dołuje · POLAND
WWW.FLASH-BUTRYM.PL