Flashforge ADVENTURER 3 V2 User manual

This guide is only applicable to FLASHFORGE Adventurer3 V2 3D printer
ADVENTURER 3 V2
Quick Start Guide

Unpacking
1. Open the box. 2. Remove wrapping paper box on the top,
there is a Quick start, an after-sales
service, an accessory kit, a power cable
and a roll of material on the plastic box.
01
3. Take out the printer of the carton,
remove bubble pack outside the
printer.
4. Tear o fixed tapes and front door
protective bag.
5. Take power cable out and plug it
into power input.
6. Plug the other end of power cable into
socket, turn on the power switch.

9. Tap [Tools]-[Setting] on the touch screen as the
picture showed above, tap [Move].
Move Camera
FilamentCheck Led
<
2/3
<
Status Language
Calibration Home
1/3
< <
Build
Tools
Filament
Network Preheat
Setting About
7. Turn on the power switch. 8. Open the front door.
02

10.Tap the upper arrow in the moving page to make the extruder raises for
removing the paper box on the bottom easier.
11.Squeeze wrapping paper box to the
middle slighly and take it out.
X
YZ
X: 20.00 Y: 45.00 Z: 36.00
12. Unboxing completed! Recommended that
you take good care of packing materials for
furthur carrying and keeping.
03

3D Printer Filament
ScrewdriverQuick Start Guide0.3mm 240℃Nozzle 0.4mm 265℃
High Temperature
Nozzle
Power Cable Flexible Build Plate
Kit Contents
Grease
04
Allen WrenchUnclogging Pin Tool

Getting to know your Adventurer 3 V2
1. Filament guide tube 2. Filament guide tube joint 3. Extruder base
4.Cooling Fan 5. Removable nozzle 6. Extruder cables 7. Clip 8. Led light
9. Turbo Fan Bae 10. Front door 11.Y-Axis sliding slot 12.Platform base
13. Removable build plate 14.Touch-screen 15.USB stick input 16.Power switch
17. Power input 18. Spool holder 19.Filament cover 20. Filament cover handle
21. Moto 22. Filament intake 23.Filament feeding wheel 24. Top cover
25. Air outlet 26. Ethernet input
05

3. Open the filament cover, insert the filament into the
filament intake, push filament into the feeding wheel
until some resistance is sensed.
Note: Please make sure filament has been pushed into
the feeding wheel!
First Print
1. Tap [Filament], tap [Load], after load completed, tap [OK].
2. As shown on the left, loading starts when the
extruder heated to target temperature.
Build
Tools
Filament
Load
Change
200 /235℃
Heating extruder...
Cancel
235 /235℃
Preheat completed,
Begin loading...
ok
06

4. Load completed when you see filament come out
of extruder, tap [OK]. Put the spool of filament on
the spool holder, close the filament cover.
Mind the loading direction of filament, make sure to be clockwise as the picture
showed.
235 /235℃
Press ok when new color appears
ok
07

1. Tap [Build], choose the file path: Print from local memory card.
2. Locate the model file in the model list,
Tap on its right to start printing; or tap
model file picture or file name to enter model
details page, tap to start printing.
3. Extruder will heat up and printer will start printing after heating completed. After
model printing finished, printer will sound a beep and pop out notice on touch
screen.
Model Print
m
08

Model Remove
1.As showed in picture, press down dotted line area and draw out
the removable build plate.
When printing completed, extruder and build plate may still hot,
please start operating after cooling down!
2.Bend the build plate, the plate will produce certain deformation, seperating
the plate away from the bottom of model (Please use a scraper to assist
removing when model is too small or big).
Notices
09