Flashforge Adventurer 5M User manual

Adventurer 5M
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch

2
English
3 –21
Čeština
22 –40
Slovenčina
41 –59
Magyar
60 –78
Deutsch
79 –98

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
󹘯󹘰󹘱󹘲󹘳www.alza.co.uk/kontakt
✆[phone]
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz
Safety Notice
Please carefully read and strictly follow all the safety warnings and notices below all the
time.
Note: Each 3D printer undergoes printing tests before leaving the factory. Filament
residue on the nozzle or slight scratches on the build plate are normal and do not affect
usage.
Work Environment Safety
•Please keep the workspace clean and tidy.
•Please ensure the equipment operates away from combustible gases, liquids,
and dust. High temperatures generated during operation may react with
combustible gases, liquids, or airborne dust, potentially causing fires.
•Children and untrained individuals should not operate the equipment alone.
Electrical Safety
•Please properly ground the equipment. Do not modify the plug. Ungrounded
equipment/improperly grounded equipment/modified plug will inevitably
increase the risk of electric leakage.
•Avoid exposing the equipment to damp or direct sunlight environments.
Humidity will increase the risk of electric leakage. Exposure to sunlight will
accelerate the aging of plastic parts.
•Make sure to only use the power cord provided by Flashforge.
•Do not use the equipment during thunderstorms.
•Please turn off the equipment and unplug it if it is not in use for a long time.

4
Personal Safety
•Do not touch the extruder, build plate, etc., during printing.
•Do not touch the extruder and build plate after finishing printing to avoid high
temperature burns or mechanical damage.
•Do not wear scarves, masks, gloves, jewelry, or other objects that can easily get
tangled into the equipment while operating it.
•Do not operate the equipment while you are tired or under the influence of
drugs, alcohol, or medication.
Cautions
•Keep the inside of the equipment clean. Do not drop metal objects into the
grooves at the bottom of the build plate.
•Please clean up filament debris in time. It is recommended to operate this
outside the equipment.
•Any modification of the equipment by yourself will void the warranty.
•Please keep the distance between the extruder and build plate for at least 50mm
during filament loading. Too-close distance may cause nozzle clogs.
•Please operate the equipment in a well-ventilated environment.
•Do not use the equipment for illegal activities.
•Do not use the equipment to make food storage containers.
•Do not place printed models into your mouth.
Equipment Environment Requirements
Room temperature: 15-30℃; Humidity: 20-70RH%
Equipment Placement Requirements
The equipment must be placed in a dry and well-ventilated environment. A distance of
at least 20cm must be reserved around the front, back, left, and right sides of the
equipment. Recommended storage temperature: 0-40°C.
Compatible Filament Requirements
When using this equipment, it's recommended to use Flashforge's filaments. If non-
Flashforge filaments are used, there will be certain differences in material properties,
and print parameters may need adjustments.
Filament Storage Requirements
Please store filaments in a dry and dust-free environment after unpacking. It is
recommended to use the matching filament dry box for storage.

5
Equipment Introduction
1. Extruder
2. Touch screen
3. Build plate
4. USB port
5. Screw holes for spool holder
6. Filament detection sensor
7. Ethernet port
8. Power switch
9. Power socket

6
Printer Parameters
Device name
Adventurer 5M
Extruder quantity
1
Printing precision
±0.2mm (testing based on 100mm cubes)
Positioning accuracy
X/Y-axis: 0.0125mm
Z-axis: 0.0025mm
Layer thickness
0.1-0.4mm
Build volume
220×220×220mm
Nozzle diameter
0.4mm default (0.25/0.6/0.8mm optional)
Printing speed
10-300mm/s
Max acceleration
20000mm/s2
Max travel speed
600mm/s
Max extruder temperature
280°C
Supported filament
*PLA/*PETG (0.4mm nozzle)
*TPU/PLA-CF/PETG-CF (0.6/0.8mm nozzle)
Note: Materials marked with * are
recommended for printing.
Power supply
AC 100~120V / 200~240V, 50/60Hz, 350W
Device size
353×376×413mm (excluding the display
and spool holder)
262×402×448mm (including the display,
excluding the spool holder)
Net weight
10.8kg
Connectivity
USB/Wi-Fi/Ethernet
Operating temperature
15~30°C
Compatible operating system
Windows 7/8/10/11; Linux (Ubuntu 20.04
or later); MacOS (10.9 or later)
Slicing software
FlashPrint 5
Maximum platform temperature
110°C
Levelling method
One-click auto levelling
Filament run-out reminder
Yes
Power loss recovery
Yes
Smart touch screen
4.3”
Build plate
PEI flexible steel plate

7
Initial Setup
Unboxing
Safety notice: Do not power on the printer until the installation is completed.
First, open the box. Remove the upper foam packaging, Quick Start Guide and After-
sales Service Card. Take out the machine, place it on a level workspace and remove the
packaging bags and tapes. Remove the filament, power cable, screen, and accessory box
from the chamber protective foam. Remove the inner protective foam from the
extruder. Move the chamber foam according to the arrow direction and remove the
foam.
Packing List
•3D printer
•Filament
•Power cable
•After-sales service card
•Quick start guide
•Touch screen
•Spool holder (with 2 screws)
•Grease
•Glue
•Diagonal pliers
•Unclogging pin tool
•Screwdriver
•Allen wrench (2.0, 2.5, 3.0)
Installing the Spool Holder and Filament Guide Tube
Take out the two screws and spool holder from the accessory box. Install the spool
holder at the position shown in the figure with the two screws. (Note: Please tighten
them using a 2.0mm Allen wrench.)

8
Insert the filament guide tube to the extruder and insert the other end of the filament
guide tube into the filament detection sensor.
Installing the Screen
Note: Before the installation, please remove the tape of the screen cable. Tear it off
gently to avoid damaging the cable.
As shown in the picture, insert the screen cable into the screen connector.
Lift the buckle on the screen's cable socket to the indicated position (Fig. 1), then insert
the screen cable into the socket connector. Note: Ensure proper insertion and check
alignment of the indicator line with socket. Press down the buckle on the cable socket to
the indicated position according to the arrow direction (Fig. 2).

9
Insert the buckle on the back of the screen into the printer's slot and push the screen
according to the arrow direction to lock it in place.
Unlocking the Build Plate
Note: Please ensure that the platform has been cleared up!
Please use a 2.0mm Allen wrench to remove four screws which lock the build plate (as
indicated by the arrow).
First Print
Power on the printer, turn on the power switch, and wait for the screen to respond.
Following the guide on the screen, select your preferred language. Upon language
selection, click [Next] and the machine will perform the first calibration. Vibrations and
noise during calibration are normal. (Note: Please keep the machine on a stable surface
and do not move it during calibration.)
Load the filament. First, cut off the bent part of the filament end. Hang the filament on
the spool holder. Pass it through the filament sensor until it's seen from the other end
of the filament guide tube. Push it forward to the feed roller, until it cannot go further.
(Please use PLA filament for the first print on initial setup).

10
Click [Load] and select [PLA] for the first print. Wait for the extruder to heat up. Feeding
will begin after heating. Successful filament extrusion from the nozzle indicates
successful loading. Lastly, confirm the filament guide tube is properly inserted.
Note: If no filament is extruded, manually insert the filament into the inlet and click
[Back] to retry. Feel for filament movement until it is extruded.
Please clear the filament residues on the nozzle and platform. Users must apply glue to
the platform so as to improve adhesion for the first print. Click [Print] and the machine
starts printing the built-in file (configured for PLA material).
Software Introduction & Installation
Before printing 3D model files, you need to configure slicing presets for the
corresponding printer. Recommended slicing software: OrcaSlicer / FlashPrint 5
Pre-printing steps:
•Obtain the 3D file (STEP/STL/OBJ).
•Download and install the slicing software.
•Use the slicing software to convert the file into the machine-readable format.
•Import the sliced file via a USB flash drive or network transfer to the printer for
printing.

11
OrcaSlicer
This slicing software, created by the open-source community, offers more open
configuration options. Experienced users are recommended to use this slicing software.
Download and Installation Instructions
•Download the latest slicing software from the official website:
https://github.com/SoftFever/OrcaSlicer/releases.
•Find the OrcaSlicer software package on the USB flash drive and install the
version that matches your system.
Note: Files can be imported by project, requiring a click on the project file each time you
open it. Alternatively, configs can be imported, eliminating the need to do so each time,
but this may not be compatible with higher software versions.
Using OrcaSlicer
Import Project Files
Open the installed OrcaSlicer and click [Open Project].
The profile should be in .3mf format. You can find the corresponding file on the USB
flash drive. Drag it directly into OrcaSlicer or open it directly (if the machine is not
configured with a USB flash drive, please download the corresponding profile from
Flashforge's official website).
After importing the profile, the software interface will display the corresponding printer,
and you can select the desired printing material.
Select the model file to be printed. You can drag it directly into the software or click
[File] - [Import] to import the model file (STL/STEP/OBJ/3MF, etc.).
Click [Slice all]. Once slicing is completed, click [Export G-code file], save the file to a USB
flash drive, and then insert it into the printer for printing.
Import Configs
Open the installed OrcaSlicer. Click [File] - [Import] - [Import Configs...].
The config file should be in .json format. You can find the corresponding files on the USB
flash drive, select all, and open it (if the machine is not configured with a USB flash drive,
please download the corresponding config files from Flashforge's official website).
After importing, the corresponding printer, available filaments, and recommended
parameters will be displayed. Select the model file to be printed. You can drag it directly
into the software, or click [File] - [Import] to import the model file (STL/STEP/OBJ/3MF,
etc.).
Click [Slice all]. Once slicing is completed, click [Export G-code file], save the file to a USB
flash drive, and then insert it into the printer for printing.

12
FlashPrint 5
FlashPrint 5 is not open source. It is user-friendly and suitable for users with no 3D
printing experience or those who don't require parameter adjustments.
Download and Installation Instructions
•Download the latest slicing software from the official website:
https://www.flashforge.com/download-center.
•Find the FlashPrint 5 software package on the USB flash drive and install the
version that matches your system.
After installing the slicing software, import the model file by clicking [File] and [Load File]
or by pressing CTRL+O. Select the corresponding printer type. Click [Start Slicing]. After
slicing is completed, save the file to a USB flash drive for printing.
Note: The slicing profiles available in FlashPrint 5 are configured based on extensive
testing with various types of filaments. We recommend using the recommended
temperature settings provided in the profiles. If you believe a specific filament requires a
different temperature, you can make minor adjustments and print smaller objects at the
set temperature for testing to ensure smooth operation.
Printing
Filament Loading and Changing
Filament loading: Click the filament icon in the printer’s interface to enter the filament
loading interface and follow on-screen instructions to complete the filament loading.
Filament changing: Click the filament icon in the printer’s interface and click on the
filament change icon and follow on-screen instructions to complete filament changing.
Pull out the filament guide tube as shown and cut the filament.

13
Pull out the cut filament and insert the new filament into the filament guide tube. If the
material type is changed, click [PLA] to select the corresponding material type.
Click [Start], wait for the extruder to heat up and filament feeding will begin. When you
see the previous filament is extruded, insert the new filament, and observe its flow and
the extrusion. If the new filament smoothly comes out of the nozzle, the filament change
is successful. If not, hold the filament by hand, insert it into the inlet, and click [Again] to
retry. Feel for filament movement until it is extruded. After successful loading, insert the
filament guide tube into the inlet.
Notes:
•If the previous filament roll is completely used up and there is no filament in the
guide tube, you can proceed with the loading process directly.
•When changing filament, try to clear out the old filament using the new filament.
•You can click the [?] button to view the nozzle usage guide on the screen.
Network Connection
Click on settings and then click on the Wi-Fi icon to enter the network connection
interface.
Wireless Network Connection
Turn on the Wi-Fi switch and tap to connect to the corresponding wireless network.
Once connected successfully, the network will be marked, and a Wi-Fi icon will appear at
the top right corner of the screen.
Wired Network Connection
Select [Ethernet] and plug the network cable into the Ethernet port on the back of the
printer following on-screen instructions. Once connected successfully, it will display as
[Connected], and an Ethernet icon will appear at the top right corner of the screen.
Printing Methods
Printing via USB
The printer supports printing via USB. Save the sliced file to a USB flash drive, insert it
into the printer, and select the corresponding file to start printing.
Printing via Wi-fi transfer
After successfully connecting the printer to the network, open FlashPrint 5. After
finishing slicing, click [Print] in the menu and select the Adventurer 5M as the machine to
connect to. You can connect it to the printer by entering the IP address or by automatic
scanning.
Note: The printer and the computer must be connected to the same network.
The IP address can be viewed by long-pressing the connected network or in the Printer
Info interface by clicking the Home button and then Information button.

14
Printing via FlashCloud
Click on settings and then click on the FlashCloud icon, turn on the FlashCloud switch,
and view the registration code. Open the FlashCloud website and register an account.
After email activation, you can log in and use FlashCloud: https://cloud.sz3dp.com/.
Click [My Printer] - [Add Printer]. On the Add Printer page, enter the registration code
(cloud registration code) and name the printer. After clicking [OK], the information will
appear on the printer's FlashCloud interface.
Printing via PolarCloud
Open the Polar Cloud website and register an account. Polar Cloud: https://polar3d.com
Note: Polar Cloud service may not be available in your region.
After logging in, click the icon at the top right corner, click [Settings], and click [PIN Code]
in the menu to find the PIN code. After connecting the Adventurer 5M to the network,
simply turn on the Polar Cloud switch and enter your account and PIN code.
Model Removal After Printing
Note: When printing is completed, the nozzle and build plate may still be at a high
temperature. It is recommended to allow them to cool down before removing the
model.
After printing is completed, directly take out the flexible steel plate and bend the
platform to remove the model. Ensure there is no residual filament on the platform
before the next print.
Tips on model removal:
•Please take the platform plate outside the printer for model removal to prevent
model debris from accumulating inside the printer. It's recommended to keep
the chamber clean.
•For models printed with TPU or other flexible materials, it is recommended to use
a scraper for removal, which ensures you can remove the flexible model from the
bed without causing damage.

15
Introduction to Auxiliary Functions
Levelling and Calibration
During the first startup, equipment calibration will be performed. During subsequent
use, choose levelling or vibration compensation as needed.
When to perform levelling:
•If continuously printing with PLA material, perform automatic levelling once with
no need to do so before each print. However, performing levelling can inevitably
improve the printing success rate;
•When switching between different materials (e.g., from PLA to ABS), please
perform levelling before each print;
•If the platform-nozzle distance is too far (poor adhesion) or too close (no filament
extrusion), please perform automatic levelling;
•After replacing the build plate or nozzle, please perform automatic levelling.
When to perform vibration compensation:
•When there is noticeable ghosting and ringing on 3D prints;
•After adjusting the tension of the synchronous belt;
•When the printer has been unused for a long time and is now being restarted.
Instructions:
Click on settings and click on the levelling button to enter the levelling and calibration
interface. Choose [Leveling] or [Vibration test], click [Start], and the printer will
automatically perform the corresponding operation. (Note: Before calibration, ensure
there are no foreign objects on the platform or at the nozzle tip.)
Other Function Settings
In the information interface, you can enable or disable sound and filament detection,
and perform firmware updates.
•When [Filament detect] is enabled, the printer will stop printing if filament runs
out mid-print.
•When connected to a wireless network, click [Firmware update] to view the
current version, check for updates, and perform online firmware updates.

16
Maintenance
Suggestions on Platform Plate Usage
•Powder coated PEI plate requires glue and is suitable for printing PLA/PETG/PLA-
CF/PETG-CF/ ABS/ASA. TPU printing does not require glue. This plate comes with
the printer.
•PEI film plate is suitable for printing PLA/TPU without glue. For PETG, it's
recommended to use glue. This plate can be purchased separately.
•PC sticker platform plate is suitable for printing PC/ABS/ASA. This plate can be
purchased separately.
•After applying glue to the platform plate, it can be cleaned with water.
•If the platform plate gets oily, it can be cleaned with a dish detergent.
•If the platform plate deforms significantly after long-term use, it's recommended
to replace it with a new one.
Suggestions on Nozzle Usage
•Please use one nozzle for the same type of material to avoid clogs and extend
nozzle lifespan, especially when working with fibre-reinforced materials and
PETG. Please avoid mixing them with other materials.
•When switching to a different material with the same nozzle, if the new material's
printing temperature is lower, adjust the setting to a higher temperature for
filament extrusion to purge old filament from the nozzle.
•When switching to a different material with a higher printing temperature, just
load the new filament.
•To clean residual filament inside the nozzle, you can perform multiple filaments
loading or manually clear any remaining filament using the unclogging pin tool.
•After replacing the nozzle, please perform levelling again.
General Maintenance
•Please apply lubricating oil to the guide rails after 200 hours of printing.
•Please replace the filter cotton every 300 hours of printing or when it appears
darker in colour.
•Please clean the filament residue inside the equipment chamber in time.

17
Frequently Asked Questions
How to unclog the nozzle?
Method 1: Click [Load] and heat the nozzle to the printing temperature of the used
filament. After heating, remove the filament guide tube, and check if the filament is bent
or filament tip is not smooth. If so, trim and insert the guide tube and filament into the
nozzle, then click [Load] and check.
Method 2: If Method 1 doesn't work, use the unclogging pin tool.
Method 3: If Method 2 doesn't work, please replace the nozzle.
How to replace the nozzle?
Note: Please power off the printer before replacing to nozzle!
First, remove the filament guide tube and cut the filament. Press the left and right
buckles and remove the nozzle. Trim the filament along the nozzle top. Insert the new
nozzle into the extruder and you can hear a "click" sound indicating the buckle position
has changed. Ensure that the nozzle slot aligns flush with the bottom of the extruder.
Note: If you have trouble aligning the nozzle, you can press the buckles during
installation or remove the front cover of the extruder (grab the lower part of the front
cover with your hand and lift it upward slightly) to check the position.
Whether it is installed in place is judged as follows:
•Ensure the nozzle is pressed to the bottom firmly during installation.
•Check if it is properly installed:
oCheck the red buckle positions on the left and right.
oCheck if the nozzle slot is flush with the bottom of the extruder (if your
view is obstructed, you can remove the front cover of the extruder to
observe).
Power up the printer, click the filament button to enter the loading interface, and follow
the on-screen instructions to complete filament loading. Filament coming out of the new
nozzle smoothly indicates a successful nozzle replacement.
Is levelling required after nozzle replacement?
Yes. It is recommended to perform automatic levelling to ensure high print quality as
slight errors may occur during nozzle installation. The equipment defaults to the
levelling operation before each print.

18
What to do if the extruder moves but doesn't extrude filament at the beginning of
printing after clicking the model for printing?
Observe the filament guide tube to check if filament has entered the nozzle. If not,
please click [Load] until filament comes out. If that doesn’t help, check if the nozzle is
clogged. If so, please refer to the solution of the first question “How to unclog the
nozzle”.
What to do if the nozzle position is too high (far from the platform) or too low
(hitting the platform) during printing? How to level it?
Please check if the platform is properly installed and there is no excessive residue on the
nozzle. If these issues exist, address them first. Then, go to the settings interface, select
the levelling option, and perform automatic levelling or enable automatic levelling
before printing.
Can filaments from other brands be used?
Yes. You can use filaments from other brands, but certain parameter adjustments are
required due to slight temperature differences in different filaments.
Is it safe to print with ABS material?
ABS can release toxic gases during heating. If conditions permit, consider printing in a
well-ventilated area. It is recommended to print non-toxic materials such as PLA in
children's activity places.
What to do if the printed model warps or doesn't adhere well?
Method 1: Increasing the platform temperature can improve the adhesion between the
platform and the model.
Method 2: Adding a brim during model slicing can alleviate the issue.
Method 3: Apply glue.
Method 4: Clean the platform to remove any oil or dirt.
Method 5: Check if the platform is level. The levelling and calibration function can be
used.

19
What to do if print files cannot be found and the screen displays only folders after
inserting the USB flash drive?
The USB flash drive format is incorrect. The printer supports the FAT32 file system.
Please format the USB flash drive to FAT32.
What to do with the Wi-Fi connection failure?
Please check if the Wi-Fi name contains special characters. If so, modify it and try again.
Furthermore, please check if the password contains special characters. If so, modify it
and try again.
What to do during a firmware update?
Do not power off the printer or disconnect from the network during firmware download
or update to prevent update failures.
Why is the boot screen white?
If the startup sound can be heard, please replace the screen or cable. If not, please
contact the Alza customer care.

20
Warranty Conditions
A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you
need repair or other services during the warranty period, contact the product seller
directly, you must provide the original proof of purchase with the date of purchase.
The following are considered to be a conflict with the warranty conditions, for
which the claimed claim may not be recognized:
•Using the product for any purpose other than that for which the product is intended
or failing to follow the instructions for maintenance, operation, and service of the
product.
•Damage to the product by a natural disaster, the intervention of an unauthorized
person or mechanically through the fault of the buyer (e.g., during transport,
cleaning by inappropriate means, etc.).
•Natural wear and aging of consumables or components during use (such as
batteries, etc.).
•Exposure to adverse external influences, such as sunlight and other radiation or
electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage,
electrostatic discharge voltage (including lightning), faulty supply or input voltage and
inappropriate polarity of this voltage, chemical processes such as used power
supplies, etc.
•If anyone has made modifications, modifications, alterations to the design or
adaptation to change or extend the functions of the product compared to the
purchased design or use of non-original components.