Flashforge ADVENTURER 3 User manual

本手册仅适用于闪铸科技 Adventurer3 3D打印机
This guide is only applicable to FLASHFORGE Adventurer3 3D printer
快速启动指南
ADVENTURER 3 /冒险家 3
Quick Start Guide
中文P11
SZ16-ZN/EN-A05

Unpacking
1. Open the box. 2. Remove wrapping paper box on the top,
there is a Quick start, an after-sales service,
an accessory kit, a power cable and a roll
of material on the plastic box.
01
3. Take out the printer of the carton, remove
bubble pack outside the printer.
4. Tear off fixed tapes and front door
protective bag.
5. Take power cable out and plug it into power
input.
6. Plug the other end of power cable into socket,
turn on the power switch.

9. Tap [Tools]-[Setting] on the touch screen as the picture
showed above, tap [Move].
Move Camera
FilamentCheck Led
<
2/3
<
Status Language
Calibration Home
1/3
< <
Build
Tools
Filament
Network Preheat
Setting About
7. Turn on the power switch. 8. Open the front door.
02

10. Tap the upper arrow in the moving page to make the extruder raises for removing the
paper box on the bottom easier.
11. Squeeze wrapping paper box to the
middle slighly and take it out.
X
YZ
X: 20.00 Y: 45.00 Z: 36.00
12. Unboxing completed! Recommended that
you take good care of packing materials for
furthur carrying and keeping.
03

3D Printer Filament After-sales
service card
Allen WrenchScrewdriverQuick Start Guide Unclogging Pin Tool
Power Cable
Kit Contents
本手册仅适用于闪铸科技 Adventurer3 3D打印机
快速启动指南
Thisguide is only applicable to FLASHFORGEAdventurer3 3D printer
ADVENTURER3 发明家 3
SZ16-ZN/EN-A01
1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
1.Hot! Avoid touching the heating nozzle and heating build plate in operation.
Pleaserefer to FlashForge official websitewww.flashforge.com to download
thenewest User Guide and Quick Start Guide.
(SUPPORT-SupportCenter - Select a Product)
2.Moving parts in printer may cause injury. Do not weargloves or other
sourcesof entanglement in operation.
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。
最新版本说明书请前往闪铸科技官方网站www.sz3dp.com下载。
（技术支持 - 下载中心 - 说明书/快速启动指南下载）
9
Grease
04

Getting to know your Adventurer 3
1. Filament guide tube 2. Filament guide tube joint 3. Extruder base 4.Cooling Fan
5. Removable nozzle 6. Extruder cables 7. Clip 8. Led light
9. Turbo Fan Baffle 10. Front door 11.Y-Axis sliding slot 12.Platform base
13. Removable build plate 14.Touch-screen 15.USB stick input 16.Power switch
17. Power input 18. Spool holder 19.Filament cover 20. Filament cover handle
21. Moto 22. Filament intake 23.Filament feeding wheel 24. Top cover
25. Air outlet 26. Ethernet input
2
3
4
5
16
7
8
9
22
23
10
13
11
12
14 15
21
16
17
18
19
20
24
25
26
05

3. Open the filament cover, insert the filament into the
filament intake, push filament into the feeding wheel
until some resistance is sensed.
Note: Please make sure filament has been pushed into
the feeding wheel!
First Print
1. Tap [Filament], tap [Load], after load completed, tap [OK].
2. As shown on the left, loading starts when the extruder
heated to target temperature.
Build
Tools
Filament
Load
Change
200 /235℃
Heating extruder...
Cancel
235 /235℃
Preheat completed,
Begin loading...
ok
06

4. Load completed when you see filament come out of
extruder, tap [OK]. Put the spool of filament on the spool
holder, close the filament cover.
Mind the loading direction of filament, make sure to be clockwise as the picture
showed.
235 /235℃
Press ok when new color appears
ok
07

1. Tap [Build], choose the file path: Print from local memory card.
2. Locate the model file in the model list, Tap on its right to start printing;
or tap model file picture or file name to enter model details page, tap to start printing.
3. Extruder will heat up and printer will start printing after heating completed. After model
printing finished, printer will sound a beep and pop out notice on touch screen.
Model Print
Build
Tools
Filament
6.67GB
No job
Not Available
1/3
< <
...
0h10 min
Time Remaining
m
7.49
20mm_Box-
PLA.gx
20mm_Box-PLA.gx
20mm_Box-P...
0 h 10 min
0.70M
Build completed!
ok
08