Flight Model EXTRA-330SC 60CC User manual

Wing Span:93 in /2326mm Flying Weight:7800-8000g;
Wing Area:110.7sq.dm; Radio:6Channel 6Servos;
Length:95 in / 2414.3mm; Engine:60CC Gas
CAUTION : this plane is not a toy and should be kept away
children under 16 years of age! Before use , please carefully read
this manual.
●First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce its
performance to full extent .
●Assemble this kit only in places out of children’s reach!
●Take enough safety percautions prior to operating this model.
You are responsible for this model’s assembly and safe operation!
●Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
P.1

MAIN WINGS
Gather wing parts as shown.
Install the aileron horns in place
with AB glue.
Install the servo after
pulling the servo extention wire
in the wing.Install the servo arm
on the servo and loctitle it in place
on the mount screw.Install the
pushrod and control horn.
●Use screw to fixed winglet
●Check to make sure you have
the servos in a reverse manner
so ailerons with work properly.
P.2

STABILIZER AND RUDDER
●Stabilizer parts together
●Apply epoxy into hinge hole
of the elevator
●Attach the servo extension wire
using foam wire holding brackes
or zip ties to the formers along
the sides of the fuse so they
can't interfere with the rudder
control cables.
P.3

Mount the servo arm on to the
elevator push rod before installing
it on the servo so you can tighten
the nylon insert locking nut to the
mounting screw.
Slide the stab on to the alumium
tube and attach to fuse using the
bolts provided.
●Make sure the bolts has been
totally screwed into the blind nuts.
Install the servo arm to the servo
after making sure the elevator is
level with the stab with the servo
is in dead center.Tape the
elevator in place using blue
painter's masking tape.
Bolt on tabs for
stabs
P.4

●Gather rudder parts as shown.
●Make sure to allow room for
epoxy to penetrate the hinges.
Carefully slide the rudder onto
each hinge and against the trailing
edge of the fin.Wipe away excess
epoxy with alcohol wetted wipes.
●Ensure there is no gap
between fin and rudder.
Install the rudder servo in the
fuselage that prepared by factory.
Feed the rudder cable through the
cable exit tube in the tail of the
fuse toward the front of the fuse.
Repeat on other side.
Adjust rudder pull-pull cables
to desied tension by screwing in
or out on the threaded couplers
and or ball links.Make all adjust-
ments with the rudder servos still
powered up and centered,and the
rudder still taped in the neutral
position.
Push
rods
Rudder
servo arm
P.5

●Connect the main wings and the
fuselage with CF tube
MAIN LANDING GEAR AND TAIL WHEEL
●Gather landing gear parts
as shown.
●Install the main landing gear
with
the bolts provided and use blind
nuts already installed and use
blue Loctite on the mounting
bolts.
●Bottom View
P.6

●Put the shield in the landing
gear
●Drill holes，as shown
●Use screw to lock it
P.7

●Install the wheel cover,
and fix it up to landing
gear with screw.
The finished photo as shown.
P.8

●Gather tail wheel parts as shown.
●Use screw to lock tail landing
gear on the wing bottom
●Measure the length of the engine
from the firewall mounts to the
prop thrust washer for the proper
distance allowing 1/4" to 1/2" from
the dege of the cowl.
Move if needed.
P.9

●Draw the engine ecnter line and
thrust line darker with a ball point.
Note the 2 degree right thrust built
in to the firewall.
●The cowl is already built with this
offset as well.
●Use the drill template if you are
going to use a DLE 60 or measure
your engines mounting location.
Remember the engine is mounted
inverted.
FUEL TANK
● Assembly diagram.
P.10

●Gather fuel tank parts as shown
Install the fuel tank mounting
ties under the fuel tank floor.
Install the battery,receiver and
switch in place as shown.
Velcro tank straps
over foam.
P.11

CANOPY
Slide the rubber backed washers
on the hatch mounting bolts and
insert bolts through the hatch
mounting holes and into the fuse
blind nuts.Tighten snugly but do
not over tighten and crush the
hatch or the fuse sides.
COWLING
Mount the cowl using the cowl
mounting screws and rubber
backed washers.the rubber
backed washers are to prevent
the fiberglass cowl from cracking
from normal engine vibration.
P.12

CG POSITION & CONTROL THROWS
P.13

THE FINISHED PHOTO
Another scheme for choice
Flight Model MFG CO.,LTD
ADD:No.10,Fu Ning Street,Xian Xi Industrial,Chang An Town,Dong
Guan City,Guang Dong Province,China
Tel: [phone]
Fax: [phone]
E-mail:[e-mail]
Web: http://www.flight-model.com/products_list.html
http://flight-model.en.alibaba.com/
P.14

children under 16 years of age! Before use , please carefully read
P.15

P.16

P.17

P.18

P.19

P.20