Flight Model EDGE-540 50CC User manual

CAUTION:This plane is not a toy!
Before use, please carefully read this
manual.
Wing span:84.9in/2158mm; Weight:5800g;
Wing area:83.9sq.dm; Engine:50cc gas;
Length:78.7in/2000mm Radio:6channels 6sevors

Gather the elevator, aluminium
joiner and elevator parts.
Connect the elevator and the
aileron by hings with AB glue.
Be sure to apply type AB glue
to full sides of each hinges.
ELEVATOR

Find out and cut the holes for
the servos and elevator joiner
in the fuselage.
Install the stablizers into
the reprepared hole .
Use two TP screws to fiting
up the stablizers to the
fuselage on each side.

Connect the servo wire to the
extension in the fuselage.
Screw the servo to the right
position in the fuselage.
Install the tri-horn on the
right position, and fixup it
with screw.
Connect the tri-horn and servo
with pushrod.

Gather the rudder,tailwheel,
tail landing gear and other
parts together.
Connect the rudder and the
fuselage by hings with AB glue
.
Be sure to apply type AB glue
to full sides of each hinges.
RUDDER AND TAILWHEEL

Gather the linkage parts
shown below.
Loop the cable back through
the brass swage tube as shown.
Crimp the brass tube with a
criming tool or pliers.

Attach a metal threaded RC
link to each threaded coupler.
Attach the RC links to the
rudder servo arm and then
attach the servo arm to the
rudder servo as shown.
Fixup the tri-horn onto the
rudder as shown.

Gather the carbon joiner,main
wings and other parts.
Apply AB glue
to all sides of each hinges,
to connect the aileron.
MAIN WINGS

Install the servo into the
fuselage and pull out the
servo wire from the hole shown
.
Install the tri-horn on the
right position, and fixup it
with screw.
Connect the tri-horn and servo
with pushrod.
shown.
Find out the drilled holes on
the fuselage as shown.

Screw the wings to the
fuselage as shown.
The canopy as shown.
Fixup the canopy to the
fuselage with TP screw.

Wheel mounted on center of
the axle.
Install the wheel cover in the
right position.
Tighten the axle so it does
not ratate during final
tightening.Install wheel
pants with two mounting bolts.
LANDING GERA

Bolt landing gear strut to
fuselage with 4 screw.
Ensure tapered edge of the
gear strut is facing toward
the rear.
Line up the template with the
firewall thrust lines and
mark the location of the
engine mounting holes.
Use a 1/4 drill to dill the
engine mounting holes.
INSTALL THE ENGINE

Gather the engine and
mounting hardware as shown.
Use a drop of blue lock tite
on the engine mounting bolts
prior to installing .
Insert the bolts through flat
fenderwashers.the firewall
and into the engine stand
offs.Tighten firmly.

Be sure to use flat fender
washers on the back side
of the firewall to distribute
bolt pressure.
Use a 1/4 bit to drill a
pushrod exit hole in the
firewall in line with the
engine carburetor throttle
arm.
Attach the 2-56 ball link to
the throttle pushrod
and secure to the carbnretor
throttle arm with a
2-56 bolt and nylon lock nut.

Fix up the cowling with two
TP screws on each sides.
Exp
25%
25%
30%
45%
45%
45%
3D flying
Aileron 40 degrees
Elevator 40 degrees
Rudder 45 degrees
Common flying
Aileron 20 degrees
Elevator 20 degrees
Rudder 30 degrees
CG POSITION & CONTROL THROWS
Surface Throws
INSTALL THE COWLING
130MM
5.12in
130MM