Flight Model F043 Super Decathlon User manual

Wing Span:96in/2438mm; Flying Weight:5144g;
Wing Area:134sq.dm; Radio:6Channel 5Servos;
Length:63.5in/1614mm; Engine:28-35CC Gas
CAUTION : this plane is not a toy and should be kept away
children under 16 years of age! Before use , please carefully read
this manual.
●First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce its
performance to full extent .
●Assemble this kit only in places out of children’s reach!
●Take enough safety percautions prior to operating this model.
You are responsible for this model’s assembly and safe operation!
●Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
P.1

MAIN WING
apply epoxy into
hinge hole of the wing
粘
Connect the aileron and
the main wing by hinges.
Be sure to apply instant
type glue to both sides
of each hinges.
Cut the servo holes on the
bottom of the main wings
P.2

Use gule to fix up the
horns
Put the servo into the
hole and fix it with screws.
Link the servo arms and
tri-horns with pushrod
STABILIZER AND ELEVATOR
P.3

apply epoxy into
hinge hole of the elevator
Fix up the stabilizer and
elevator with hinges and AB
glue.
Cut the servo holes on the
profile of the fuselage
P.4

Install the servo in the hole
as shown
Be assured that the screw
is fixed up
Link the servo to
the elevator with pushrod.
Cut the hole of rudder
as shown
P.5

Using glue fixed rudder angle
Install the rudder servo
Be assured that the screw
is fixed up
attach the servo arm to the
ruddert servo as shown
P.6

As shown in picture, This is
TAIL WHEEL finished for the rudder servo
MAIN LANDING GEAR
Fix up the landing gear
on the fuselage bottom with
screws.
●Bottom View
Put the cover board in the
right position,then fix up it.
P.7

Install the wheel as shown.
Install the wheel cover,
and fix it up to landing
gear with screw.
Install the tail landing gear
Use screws to fix up the
fuselage bottom.
ENGINE
P.8

Drill the engine mounting
holes as the board provided
Use the ruler to measure
the length from firewall
to airscrew
Install the cowl,propeller and
spinner as shown
FUEL TANK
P.9

Install the fuel tank into
the fuselage, and fixup it
with belt.
Install the fuel tank mounting
ties under the fuel tank floor.
Install the battery,receiver and
switch in place as shown.
Wing Assemble
Fixed the steel wire
P.10

as shown
connect two strut lines in correct
location
Fix it up to aluminium sheet
with screw as shown
The finished photo as shown
P.11

Put the cover through strut lines
Use screws to fix it up
of the fuselage.
Put the cover board in the
right position,then fix up it.
Use screws to fix it up
of the fuselage.
Put the cover board in the
P.12

right position,then fix up it.
Use screws to fix it up
of the fuselage.
put the wing strut throuht to
the fuselage
wing strut fixed up on the
P.13

fuselage.
Fixed up wing strut board
use of screw
CANOPY
Install the side window into
the fuselage as shown
Install above the window into
the fuselage, as shown,
Use screws to fix up the
P.14

fuselage.
Install the canopy into
the fuselage as shown
CG POSITION & CONTROL THROWS
P.15

THE FINISHED PHOTO
P.16

Another scheme for choice
Dong Guang Flight Model CO.,Ltd
ADD:No.10,Fu Ning Street,Xian Xi Industrial,Chang An Town,
DongGuan City,Guang Dong Province,China
Tel: [phone]
Fax: [phone]
E-mail:inf[email protected]
Web: http://www.flight-model.com/product/eindex.asp
http://flight-model.preview.alibaba.com/
P.17

P.18

P.19

children under 16 years of age! Before use , please carefully read
P.20