Flight Model ZERO A6M5B User manual

For Intermediate & Advanced Fliers.
SAFETY PRECAUTIONS
This radio control model is not a toy!
Fist-time builders should seek advice from people having building
Experience in order to assemble the model correctly and to produce
Its performance to full extent.
Assemble this kit only in places out of children’s reach!
Take enough safety precautions prior to operating this model.
You are responsible for this model’s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
Notice:
**This manual included Specification, Parts list in paper and CD full instruction manual.**
Before you read the CD. Please install Acrobat Reader. First.
“Acrobat Reader” logo are trademarks of Adobe Systems Incorporated
This Products Produce by P & D Products Company
3F., 94 HAK PO ST., KLN. HONG KONG Fax: [phone]
E-mail: [email protected]

Elevator
Cut film and cut four slot as the show.
Glue the hinges with Epoxy.
Drill a 3mm hole for Elevator control
horn.
Install Elevator horn as show.

Trim out the film as show.
Install Elevator as show.
Install Elevator servo as show.

Install Elevator servo hatch as show.
Install Elevator servo , horn and linkage
as show.
Install STB. Join and anti roll pin as
show.
Then glue them all in piece with Epoxy.

Install Stb. In other side of Fus. as show.
The drill a 2.3mm hole , then use a
3X15mm TP. Screw to lockup the Stb.
Rudder
Cut film and cut three slot as the show.
Glue the three copper hinges with Epoxy.
Parts need:3 copper hinges.
Supply from separately.
Drill a 3mm hole for Rudder control
wire.
Gule it with Epoxy after you install
Rudder on the fus.

Cut a slot Rudder control wire.
as the show
Install Rudder control wire.
Drill a 3.5 hole at the root of Fin.

Install the rudder as the show.
Place the two hard wood stick and glue it
inside tail of Fus.
Install the tail landing gear as show.

Install the control put put as what kind of
that you use.
We are use Robart Retacts 160 or 160wc.
Aileron:
Cut film and cut three slot as the show.
Glue the three copper hinges with Epoxy.
Parts need:3 copper hinges.
Supply from separately.
Drill a 3mm hole for Aileron control
horn.

Install the Aileron control horn as show.
Trim off the film at the servo bay as
show.
Install Aileron servo , horn and linkage as
show.

Flap:
Cut film and cut three slot as the show.
Glue the three copper hinges with Epoxy.
Parts need:3 copper hinges.
Supply from separately.
Notice: the Hinges should be install at
the lower part of LE. Of Flap.
Drill a 3mm hole for Flap control horn.
Install Flap servo , horn and linkage as
show.
IMPORTAN NOTICE:
If you use “Y” servo lead to control the
that two Flap servo you need a reverse
direction sever, or you install control in
same direction.

Install the wing panel wing join.
Drill a 6mm hole from root first.
Then place the 6mm pin from left to right
side of wing as show.
Use lock pin and O ring wish to hold the
wing panel together as show.

Place the wing panel on fus. Bottem.
Then drill two 6mm hole from fus. As
show.
Install two wing pin at fount of wing .
Let at least 25mm out of the hole.
Then glue it together with Epoxy.
Place wing panel on the fus. Bottem
again with wing pin.
Then drill two 6mm hole for wing bolt as
show.

Follow the 6mm wing bolt hole to drill
two 8mm hole for blind nuts
Install blind nuts and glue it with epoxy.
Install the retact gear as show.
We recommend “Robart Retacts” #154.
Install the wheel cover as show.

Install the wheel cover as show.
Notice the wheel should be use 5in
wheel.
Option part:
Drill two small hole on to the tank mount
as show.
Place the tank mount on the tank and
follow the small hole you just drill and
drill two small hole again to the tank.

Use two TP. Screw to lockup the tank and
tank mount as show.
Drill two 10mm hole at the wing root
first.
Then place the tank under the wing panel
and drill two 3mm hole for tank mount
bolt.
Install two 3mm blind nuts inside the
tank mount and glue it with Epoxy.

Install the tank as the show.
Notice: you need install the wing panel
before you install the tank.
Drill the wing bolt hole as your motor
mount .
Notice, there have 2 degree right thrust
and 2 degree down thrust.
We recommend use 65cc-80cc Gas
motor.

Diver hub should be have 10-15mm out
from cowl end.
Place the Exhaust pipe on to the hard
wood block then use 3X15 TP. Screw to
fix it as show.
Glue six exhaust pipe with wood block as
show. And also glue four cowl mount
wood block as show.

Notice. When you install the exhaust pipe
you need to check and follow the
position of cowl, because the exhaust
pipe position was a bit differ in differ
side of the cowl.
Drill four 2mm hole at differ side of the
cowl and use 3X15mm TP. Screw to the
cowl.
Option parts : Interior cockpit
Cut the interior cockpit as show.

Glue the cockpit to the interior as show.
Install the cockpit panel inside the fus. as
show.
Then use thick CA. to glue it together.
Follow the mark on canopy use heat gun
to bend the edge of canopy inside 90
degree as show.

Install the Antenna and glue it together
with Epoxy as show.
Cut a open at rear canopy as show to
allow the Antenna out of the canopy.
Install the rear canopy as show.
Fix it with 3 pcs. 2.5 X 10 TP. Screw.