Symbols
Do not apply around or remove from HAZARDOUS LIVE
conductors.
43URGXFWLVSURWHFWHGE\GRXEOHLQVXODWLRQ
7Risk of Danger. Important information. See Instruction Sheet.
8Risk of Electric Shock.
&DQDGLDQ6WDQGDUGV$VVRFLDWLRQKDVFHUWL¿HGWKDWWKHSURGXFW
PHHWVDSSOLFDEOH86DQG&DQDGLDQ6WDQGDUGV
0Conforms to relevant European Union directives.
6DIHW\6SHFL¿FDWLRQV
&DWHJRU\5DWLQJ CAT III 600 V per IEC/EN61010-1, Pollution Degree 2
&RPSOLHVZLWK86DQG&DQDGLDQ6WDQGDUGV&$1&6$&
No. 61010-1-04 and No. 61010-2-032-04; UL61010-1
0IEC 61010-1 2nd Edition IEC 61010-02-032
(0& EN 61326-1, FCC for emission and immunity
Electrical Characteristics
Nominal current in 5 A ac r.m.s.
Overload up to 70 A r.m.s.
&RQGXFWRUSRVLWLRQLQÀXHQFH RIUDQJHDW+]
(UURUGXHWRDGMDFHQWFRQGXFWRU P$$DW+]
Frequency range 40 Hz to 5 kHz (-3 dB)
7HPSHUDWXUHFRHI¿FLHQW RIUDQJH&
0D[LPXPZRUNLQJYROWDJH
(see Safety section) 600 V ac r.m.s. or dc
&UHVW)DFWRU DGGWRDFFXUDF\
Output 400 mV/A
General Characteristics
0D[LPXPFRQGXFWRUVL]H PPGLDPHWHU
EXVEDU[PP
&DEOHOHQJWK P
2SHUDWLQJWHPSHUDWXUHUDQJH &WR&
6WRUDJHWHPSHUDWXUHUDQJH &WR&
2SHUDWLQJKXPLGLW\ WRUK
(non condensing)
'LPHQVLRQV LQ[LQ[LQPP[
PP[PP
:HLJKW OENJ
Connector LEMO / Redel 6 pin plug
$OWLWXGH PPD[LPXP
Accuracy (at 50 Hz)
Accuracy (48 Hz to 65 Hz)
P$WR$ P$
$WR$
Phase Shift (48 Hz to 65 Hz)
P$WRP$ 8QVSHFL¿HG
P$WR$ W\SLFDO
Reference Conditions
(QYLURQPHQWWHPSHUDWXUHUDQJH &WR&
+XPLGLW\ WRUK
&XUUHQW VLQXVRLGDOZDYHIRUPWR+]
GLVWRUWLRQIDFWRUQR'&FRPSRQHQW
/RDGLPSHGDQFHIRUYROWDJHRXWSXW 02KPS)
Measurements
)RUWKHEHVWPHDVXUHPHQW
3XWWKHFRQGXFWRULQWKHFHQWHURIWKH&XUUHQW&ODPSMDZ
Make sure that the Current Clamp is perpendicular to the conductor.
'RQRWPHDVXUHZKLOHQHDURWKHUFXUUHQWFDUU\LQJFRQGXFWRUV
Operation
87:DUQLQJ
7RSUHYHQWHOHFWULFDOVKRFNRUSHUVRQDOLQMXU\KROGWKHSURGXFWEHKLQGWKH
WDFWLOHEDUULHU
To use the Current Clamp:
1. &RQQHFWWKHFODPSFDEOHWRWKHLQVWUXPHQW
2. Make sure that the measurement instrument is set to the correct range.
3. 7RRSHQWKH&XUUHQW&ODPSMDZSXVKWKHUHOHDVHEXWWRQWRZDUGWKHMDZ
4. &RQQHFWWKH&XUUHQW&ODPSMDZVDURXQGWKHLQVXODWHGFRQGXFWRUIRU
PHDVXUHPHQWDQGUHOHDVHWKHEXWWRQ0DNHVXUHWKDWWKHUHOHDVHEXWWRQLVLQWKH
initial position to continue the circuit test.
Maintenance
87:DUQLQJ
7RSUHYHQWSRVVLEOHHOHFWULFDOVKRFNRUSHUVRQDOLQMXU\GRQRWXVHDQG
GLVDEOHWKHSURGXFWLILWLVGDPDJHG
If the Current Clamp does not correctly operate, use these steps to help isolate the
SUREOHP
1. ([DPLQHWKHMDZIRUDFOHDQPDWLQJVXUIDFH,IWKHUHLVXQZDQWHGPDWHULDOWKHMDZ
ZLOOQRWFORVHFRUUHFWO\DQGZLOOFDXVHPHDVXUHPHQWHUURUV
2. Make sure that the function selection and range are correct on the Multimeter
DQGDGMXVWHGWRWKHVHQVLWLYLW\RIWKH&XUUHQW&ODPS
Note
A damaged clamp under warranty will be repaired or replaced (at Fluke’s
discretion) at no charge.
Cleaning
,IQHFHVVDU\FOHDQWKHFDVHZLWKDGDPSFORWKDQGZHDNGHWHUJHQW
7Caution
7RSUHYHQWGDPDJHWRWKH&XUUHQW&ODPSGRQRWXVHDEUDVLYHVRUVROYHQWVWR
clean the clamp.
2SHQWKHMDZVDQGFOHDQWKHPDJQHWLFSROHSLHFHVZLWKDOLJKWO\RLOHGFORWK'RQRW
let rust or corrosion collect on the magnetic core ends.
text.indd 2 1/5/2011 10:16:30 AM
