Fly sky Fms-g7 User manual

Quick Start Guide

快速操作指南FMS-G7

Http://www.flysky-cn.com

Release date: 2022-06-07

FCC ID: N4ZMG700

Read the safety messages listed below before operation!

• Do not use the product at night or during bad weather conditions, like rain or thunderstorms.

It can cause erratic operation or loss of control.

• Do not use the product when visibility is limited.

• Do not expose the product to rain or snow. Any exposure to moisture (water or snow) may

cause erratic operation or loss of control.

• Interference may cause loss of control. To ensure the safety of you and others, do not

operate in the following places:

Thank you for purchasing the products of Flysky! To find out more about our products, visit our

website at www.flysky-cn.com. If you encounter any problems during using, please refer to the

manual first. If the problem is still not resolved, contact your local dealer directly or contact the

customer service staff via Flysky official website.

• Do not use this product when you are tired, uncomfortable, or under the influence of alcohol

or drugs. Doing so may cause serious injury to yourself or others.

• The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a large

can block the RF signal and lead to loss of control.

• Never grip the transmitter antenna during operation. It significantly degrades signal quality

and strength and may cause loss of control.

• Do not touch any part of the model that may generate heat during operation, or immediately

after use. The engine, motor or speed control, may be very hot and can cause serious burns.

• Misuse of this product may lead to serious injury or death. To ensure the safety of you and

your equipment, read this manual and follow the instructions carefully.

• Make sure the product is properly installed in your model. Failure to do so may result in

serious injury.

• Make sure that the receiver's battery is disconnected before turning off the transmitter.

Failure to do so may lead to unintended operation and cause an accident.

• Ensure that all motors operate in the correct direction. If not, adjust the direction first.

• Make sure that the model stays within range in order to prevent loss of control.

CAUTION!

• RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF

USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Precautions

Near any sites

where other radio

control activity

may occur

Near people or

roads

On any pond/lake

when passenger

boats are present

Near power lines

or communication

broadcasting

antennas

Transmitter Overview

[1] CH1 Steering wheel

[2] CH2 Throttle

[3] Neck Strap Hook

[4] CH3 Three-position switch

[5] CH4 Reset button SW2

[6] Handle contains 4 batteries(Removable

battery)

[7] Logo sticker

[8] CH6 Reset button SW4

[9] LED light in green

[10] CH5 Reset button SW3

[11] BIND button

[12] ST- trim button

[13] TH-Throttle trim button

[14] Power switch

[15] CH7 Reset button SW5

[16] REV Sterring/Throttle reverse

[17] ST+ trim button

[18] TH+Throttle trim button

Basic Operations

Power on

Follow the steps below to turn on the transmitter:

1. Check to make sure that the batteries are fully charged and installed correctly.

2. Press and hold Power Switch until the LED indicator is solid on for 3S and then goes into

three-flash-one-off state, at the time, the transmitter is in standby mode. When the receiver

is connected to transmitter normally, the transmitter LED is solid on.

Controls

The ST+ andTH+ button are for increasing trim value defaultly, the buzzer will prompt with

tone 1 short beep when the trim is successful. One beep once for a press. when press for a

while, the buzzer will prompt with quick short beep. The buzzer will prompt with 2 short beeps

when the trim is over the mid-point. When the trim is at the end, the buzzer will prompt with

long beep.

Servo travel adjustment

CH1 servo travel can be adjusted by ST+/- button.The adjustment range is 0~120%, the step is

5%, and the default value is 100%.

CH2 servo travel can be adjusted by TH+/- button. The adjustment range is 0~120%, the step is

5%, and the default value is 100%.

Channel reverse

1. When the steering wheel is in the non-centering state, the channel 1 is reversed by pressing

the REV button, and switch once when the button is pressed.

2. When the throttle trigger is in the non-centering state and the steering wheel is in the

centering state, the channel 2 is reversed by pressing the REV button, and switch once when

the button is pressed.

3. If the CH5 four-wheel steering is in the rear-wheel-only steering mode, the reverse operation

is for CH5, not for CH1.

4. When the channel reverse takes affect by pressing the REV button, the buzzer will prompt

with 1 beep. The buzzer will prompt with 1 beep for CH1 and CH5 reverse, and with 2 beep for

CH2.

Binding

Follow the steps below to bind with the receiver:

1. Press and hold the BIIND button while turning on the transmitter,the transmitter LED will

flash fast.

2. Put the receiver into binding mode.

3. The binding process is finished when the transmitter LED stops flashing and is solid on.

4. Check to make sure the transmitter and receiver are working correctly, if there are any issues

or unexpected operation arise, follow the steps above to bind again.

Note: If the transmitter disconnects with the receiver, the transmitter LED will go into three-flash-

one-off state.

1. SW2 reset button(CH4), press and hold the SW2 button for several seconds, then CH4 takes

affect, otherwise, the CH9 takes affect.

• Press and hold SW2 button over 2S, the CH4 will reverse while the CH9 isn't changed.

• Press and hold SW2 button within 2S, the CH9 will reverse while theCH4 isn't changed.

2. SW3 reset button(CH5) is four-wheel steering switch.The four mode will switch by pressing

the button once.

3. SW4 reset button(CH6), the default output value is 1000us. When press the SW4 button

once, the output value will change to 2000us.The buzzer will prompt with 1 short beep when

switching to 1000us, and 2 short beeps for 2000us.

4. SW5 reset button(CH7), to turn on/off winch function. The winch function is enabled when

the transmitter is powered on defaultly.

• When winch function is enabled, CH7 value can be adjusted by ST+/- button.

• When winch function is enabled over 3S and the ST+ button is not operated, the winch

function is disabled automatically, then CH7 outputs neutral value prompted with 2 short

beeps on tone 1.

Channels opration description

Failsafe

Stick Calibration

Data resetting

When the transmitter is turned on, keep the channel output at the desired value, then press and

hold the BIND button for 3S, after the buzzer prompts with long beep on tone 1, the failsafe is

set successful.

The default setting of the failsafe is no setting.

When the transmitter rebinds, the failsafe is reset to default setting.

1. Turn the Steering Wheel to the Max endpoint in a clockwise direction and push the trigger

forward to its maximum endpoint while powering on the transmitter, then the transmitter

enters stick calibration mode.

2. Turn the Steering Wheel or push the trigger to the Max or Min endpoint, then return to its

neutral point.

3. After the calibration is finished, press the BIND button to exit the calibration mode. If the

calibration is failed, then the setting can not be saved by pressing the BIND button.

Follow the steps below to reset the data.

1. Press and hold the BIND button and the REV button while powering on the transmitter, the

data will be reset.

2. When the operation is successful, the buzzer will prompt with long beep on tone 2.

Follow the steps below to calibrate the transmitter.

Low voltage alarm

Idle alarm

When the transmitter voltage is lower than 4.2V, it will enter low voltage alarm mode. The

transmitter LED will be in slow flashing state for prompt.

When the transmitter is not operated over 10 minutes, it will go into idle alarm state.

In idle alarm state, the transmitter will exit idle alarm mode when any control is operated.

When the transmitter is in idle alarm state over 2 minutes,the transmitter will go into sleep

mode. Repower on the transmitter to exit the sleep mode.

Certifications

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

EU DoC Declaration

Hereby, [FlyskyTechnology co., ltd] declares that the Radio Equipment [FMS-G7] is in compliance

with RED 2014/53/EU.

The full text of the EU DoC is available at the following internet address:

www.flysky-cn.com.

FSM-G7

Digital Proportional Radio Control System

本说明书中的图片和插图仅供参考，可能与实际产品外观有所不同。产品设计和规格可能会有所更改，恕不另行通知。Figures and illustrations in this manual are provided for reference only and may differ from actual

product appearance. Product design and specificatiions may be changed without notice.

Manufacturer：ShenZhen FLYSKY Technology Co.,LtdAddress: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, ChinaRF Exposure Compliance

The device has been evaluated to meet general RF exposure requirement. The device can be used

in portable exposure condition without restriction.

Environmentally friendly disposal