Flycam Vista-II User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
Vista-II Stabilizer Arm & Vest (VSTA-II-AV)
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Assembly Manua l
Vista-II Vest back (Part-1a)
Vista-II Arm (Part-3)
Storage Bag (Part-5)
Vista-II Vest front (Part-1)
2x Heavy
Tension Springs
3/16mm,2.5mm,
1.5mm Allen Key
Hip Pad (Part-2)
2x Bush (Part-4)

2
Safety Hints
ATTENTION: PLEASE READ THIS BEFORE USING TO PREVENT SERIOUS DAMAGE TO
THE GEAR!
BE WATCHFUL OF THE HANDS
Cauously operate to avoid pinching your hand/ngers inside the arm.
ALWAYS ESTABLISH THE CORRECT BALANCE
Adjust the weight balance before telescoping the length.
NEVER LEAVE THE FIXTURES LOOSE
All the knobs/screws must be locked ghtly to avoid unbalancing of the whole
camera setup.
BE HIGHLY VIGILANT WHILE ASSEMBLING
Lack of aenon while aaching Stabilizer, Arm & Vest together can cause
substanal damage to equipment.
NEVER LEAVE THE ARM UNATTANDED
Don’t let an unloaded arm swing about as it may hit you or someone near you.
FOLLOWING THESE GUIDELINES WILL PROVIDE BETTER SHOTS AND TROUBLE-FREE
OPERATION.
SHOULD YOU NEED ADDITIONAL INFORMATION, TECHNICAL ASSISTANCE IS
AVAILABLE ‘ONLINE’ BY CONTACTING OUR SALES REPRESENTATIVE.

3
1. Aach both parts of Jacket by aaching the
top shoulder buckles (Part-1a) with
(Part-1).
2. Follow same step on other side. Then wear
the jacket/vest.
3. Aer wearing the Vest, aach the waist
buckles (Part-1a) with (Part-1) of both side.
4. Now aach the Hip Pad (Part-2) from both
sides by aaching the buckles with (Part-1)
5. Then ghten the strap properly.
Vista-II Vest Setup
8. You can also adjust the height of the Socket
Block (Part-1).
9. Adjust the Height provided with the knob.
6. Length of chest plate (Part-1) can be adjusted
according to the height of person.
7. Then Using the pin & knob (Part-1), as shown
in image.
10. You can also remove the Socket Block (Part-1)
11. Adjust to le and right posion with the pro-
vided knob as shown in the image.
1 2
3
4 5
7 6
11
10
9
8

4
12. Loosen the knobs of Socket Block on Vest
(Part-1).
13.Then Insert male connecng socket of Arm
(Part-3) into Socket Block of Vest (Part-1).
14. Aer ghtening the both knobs of Socket
Block on Vest (Part-1) to secure the secon.
15. You can adjust the tension of Arm (Part-3)
with mounted Stabilizer, by provided knob,
according to your setup requirement.
16. Adjust the li with Arm angled slightly up,
and the knob will turn easily. Both Arm
secons should track together.
17. Insert bush (Part-4) on arm mounng post
(Part-3)
18.Then insert into the handle of your stabilizer.
NOTE: 17. For aaching the Stabilizer to Arm & Vest, keep the handle of Stabilizer straight in accordance
to the pin of Arm.
18. There is a 16mm mounng post and we are giving 19 and 22mm bush, so you can easily mount the
stabilizer (Not Included) on mounng post of arm according to your requirement.
Vista-ll Arm Setup
NOTE: It can be operated eciently either right or le handed.
NOTE: Adjust the ‘forearm’ (secon nearest to Stabilizer) rst, then the ‘upper arm’ secon.
14
13
18
12
15
17
16

5
To Use As Single Arm Conguraon
19. Pull the pin from middle jointer.
20. Remove one secon of the Arm (Part-3).
23. Finally, single arm (Part-3) properly aached
as shown in the image.
21. Now, aach the single arm (Part-3)
22. Insert the pin from middle jointer to secure
with it.
19
21
20
22
23
The arm tension is adjusted for the heaviest camcorder it can hold, so it does not bottom-out when you
put the camcorder and sled on it for the first time.
Now adjust Arm for the weight of your camcorder:
 With the Vest On, attach Arm & unlock the rig.
 Move Arm to the middle of its booming (up and down) range and let go (If it stays where it is, you are
probably close to the right adjustment).
 Keep making small adjustments until the camcorder does not rise or fall when you let go of it in the
middle of its booming range.
Arm Adjustment
Posion arm
 Move the camcorder to your left so the arm crosses your body.
 Adjust the arc of your arm so the rig feels comfortable to you.
 Keep the camcorder close to your body.
For Interchanging the Spring, Follow this video
https://bit.ly/3eYzHs6

6
YOUR VISTA-II STABILIZER ARM & VEST
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Bearing Maintenance
If aer some period of me the bearings stop running smoothly as when new, you can oil it with light
lubricang oil. We recommend using only a few drops, anything more than a lile will end up dripping
from bearing and onto the rest of your Arm. Be sure to keep the oil away from your Camera, and clean up
any over-spill when done.
Cleaning
Do not use solvents or harsh cleaners of any kind on Vista-II Arm & Vest. If the unit becomes dirty, use
only a cloth or sponge with water and a very mild detergent to gently rub the unit clean. Rinse well.
Storage
If you are going to store Flycam Vista-II Arm & Vest for a long period of me, then we recommend storing
it up-right in a dry or low-to-normal humidity area.
If you are unable to nd an environment like this, then we suggest you store the unit in an airght plasc
container or bag. Keeping the unit upright helps to lessen stress on the system.
Maintenance

7
Warranty: We oer one year warranty for our products from date of purchase. Within this period of
me, we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor
does it cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to
inspecon and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.