Flying Industry Development S4PUA-AC220 User manual

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
RF Wireless Remote Control Radio Controller / Transmitter & Receiver
Package Include:
1 x Receiver: S4PUA-AC220 (4 Channel / Four Control Modes / AC100~240V)
2 x Transmitter: CWB-4
1 x User manual
Features:
Wireless control, easy to install
Control Lights, Motors, Fans, electrically operated Doors / Locks / Windows / Blinds / Cars or OtherAppliances with AC110~240V or DC0~28V.
Universal input: support voltage of AC110V (100V~120V), widely used in US, Canada... and voltage of AC220V (200V~240V), used in UK,
France...
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass
through walls, floors and doors.
With characteristics of reverse power protection and over current protection
Audible / visual indication
Use microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
Use ULN2003 to drive relay, with strong anti-interference.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/several transmitters can control one/several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Transmitting Frequency: 315MHz / 433MHz
Receiver:
Model No.: S4PUA-AC220
Control Mode: Latched, Momentary, Toggle, Momentary + Toggle
Coding Type: Fixed code
Coding Setting: By learning
Power Supply (Operating Voltage):AC100~240V
Working Voltage Range of Relay: AC110~240V or DC0~28V
PCB Size: 137mm x 80mm x 25mm
Case Size: 150mm x 90mm x 45mm
Maximum Working Current: 30A / each channel
Transmitter:
Model No.: 0021095 (CWB-4)
Waterproof
Shell Color: Black
Channel/Button: 4
Button Symbol:A, B, C, D
Operating Voltage: 6V (2 x CR2016 -3V button cell batteries,, can be used for 12 months)
Operating Current: 5mA
Operating Frequency: 315Mhz / 433Mhz
Encoding Chip: PT2260/ PT2262 / PT2264
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance: 50m / 150ft (theoretically)
The distance of 50m is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be
hindered by trees, walls or other constructions, and will be exposed to some interference by other signals. Therefore, the actual distance may or
may not reach 50m.
Modulation Mode: ASK
Operating Temperature: -20 °C to +70 °C
Unit Size: 56mm x 32mm x 12mm
Weight: 20g
Uses: garage doors, motorcycles, car alarm products, home security products, wireless remote control products, industrial control products.
How to set up the 8-bits code of the transmitter:
1. Open the transmitter shell, then you will see the circuit board. There are two rows pads and one row of chip feet on the back side.
2. The upper row of pads is “H”side, and the lower row of pads is “L”side.
3. If solder the middle row of chip feet to the “L”side, it is code 1. If solder the middle row of chip feet to the “H”side, it is code 2. Don’t solder to
any side, it is code 0.
4. The 8-bits code order is from right to left (from D1 to D8).
5. Here is an example, the 8-bits code in the picture is 00001020, solder as the following way:
6. Code 0: don’t solder any side, like D1, D2, D3, D4, D6, D8.
7. Code 1: solder to the “L”side, like D5.
8. Code 2: solder to the “H”side, like D7.
Usage:
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following operation):

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched (Channel 1~4): Press -> On, other relays Off; Press other button -> Off.
Such as:
Press button 1: Turn on relay 1 (connect A and B, disconnect A and C)
Turn off other relays (disconnect A and B, connect A and C)
Press button 2: Turn on relay 2 (connect A and B, disconnect A and C)
Turn off other relays (disconnect A and B, connect A and C)
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (Channel 1~4): Press and hold -> On; Release -> Off.
Such as:
Press and hold button 1: Turn on relay 1 (connect A and B, disconnect A and C)
Release button 1: Turn off relay 1 (disconnect Aand B, connect A and C)
Press and hold button 2: Turn on relay 2 (connect A and B, disconnect A and C)
Release button 2: Turn off relay 2 (disconnect A and B, connect A and C)
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle (Channel 1~4): Press -> On; Press again -> Off.
Such as:
Press button 1: Turn on relay 1 (connect A and B, disconnect A and C)
Press button 1 again: Turn off relay 1 (disconnect A and B, connect A and C)
Press button 2: Turn on relay 2 (connect A and B, disconnect A and C)
Press button 2 again: Turn off relay 2 (disconnect Aand B, connect A and C)
Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.
Control mode Momentary (Channel 1, 2): Press and hold -> On; Release -> Off.
Press and hold button 1: Turn on relay 1 (connect Aand B, disconnect A and C)
Release button 1: Turn off relay 1 (disconnect A and B, connect A and C)
Press and hold button 2: Turn on relay 2 (connect Aand B, disconnect A and C)
Release button 2: Turn off relay 2 (disconnect A and B, connect A and C)
Control mode Toggle (Channel 3, 4): Press -> On; Press again -> Off.
Press button 3: Turn on relay 3 (connect A and B, disconnect A and C)
Press button 3 again: Turn off relay 3 (disconnect A and B, connect A and C)
Press button 4: Turn on relay 4 (connect A and B, disconnect A and C)
Press button 4 again: Turn off relay 4 (disconnect A and B, connect A and C)
We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
Learning the button of remote control:
1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Relay 1
Relay 2
Relay 3
Relay 4
C
B
A
C
B
A
C
B
A
C
B
A
Antenna
RF module
IC
Button
Jumper-1
Jumper-2
Signal LED
Power LED
Application Circuit
DC0~28V / AC110~240V
Lamp 1
Lamp 2
Lamp 3
Lamp 4
N
L
Power Supply

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]