Flying Industry Development 4S1PFC-AC220+CV-8-3 User manual

SHENZHENGUIYUANINDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
RF Wireless Remote Control Kit (Model 00202114S1PFC-AC220+CV-8-3)
The receiver is designed for one-transmitter-many-receivers system. You can use a 4buttons transmitter to control 2 receivers, or use a 6
buttons transmitter to control 3receivers, or use a 8buttons transmitter to control4receivers, or use a 12buttons transmitter to control 6
receivers.
Package Include:
4 X Receiver: S1PFC-AC220
1 X Transmitter: CV-8-3
1 X Use manual
Features:
Application: It can be used in rolling blinds, rolling doors, projection screens, awnings, pumps, winches, conveyors or other appliances and
equipments withACmotors, itcan remote controlACmotor rotates in the positive or reversal direction.
Wireless control, easy to install.
Waterproof: The receiver haswaterproof caseandwaterproof connector, itcan be installed outdoors.
Youcan rotate a motor in the positive or reversal directionwith the transmitter (remote control) fromany placewithin areliable distance.
The RFwireless signal can pass throughwalls,floors and doors.
High Power: Each channel canwork at maximumcurrent 30A.
With limit control terminals: You can connect limit sw itches or sensors to stop the motor.
With wired control terminals: You can connect manual switches or external devices (w ith low level output signal, such as sensors) to control the
motor.
Designwith low-power andhigh-speed CMOS technology.
Youcan turnon/ off thereceiverwith transmitter (remote control) fromany placewithin a reliable distance.
With reverse power protection andover current protection.
Reliable control: The receiver only works with the transmitter w hich usesame code.
One/several transmitters can control one/several receivers simultaneously.
Youcan use two or more units in the same place.
Receiver Parameters:
Model No: S1PFC-AC220
Control Mode: Latched or Momentary
Coding Type: Fixed code or learning code
Coding Setting: By learning
Pow er Supply (Operating Voltage): AC100~240V (110V/120V/220V/240V)
Output:AC100~240V (110V/120V/220V/240V)
Working Frequency: 315MHz / 433MHz
Channel: 1 CH, canworkwith1AC motor
Static Current: ≤6mA
MaximumWorking Current: 30A / eachchannel, so motor's maximumstarting currentcan notexceed 30A.
PCB Size: 140mmx 73mmx 18mm
Case Size: 192mmx 100mmx 45mm
Transmitter:
Model No.: CV-8-3
Shell Color: White
Channel/Button: 8
Button Symbol: Four▲, Four▼,
Operating Voltage: 12V (1x 23A -12V battery,can be usedfor 12 months)
Operating Current: 15mA
Encoding Chip: PT2262
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance: 500m/ 1500ft (theoretically)
Modulation Mode:ASK
Operating Temperature: -20 °Cto +70 °C
Unit Size: 110mmx 50mmx 18mm
Working Range:
With a transmitter (such as CV-8-3) toformacomplete set, theworking distancecanreach 500Min an open ground. The maximumworking distance
500M is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, itwill be hindered by trees,
walls or other constructions, andwill be interfered by other wireless signals. Therefore, the actual distance may or may not reach 500M.
Usage (with transmitter CV-8-3):
Connect livewire to terminal “L”and neutralwire to terminal “N”. Then connectACmotor to terminals “UP”, “COM” and “DOWN”. You can exchange
“UP” and “DOWN”wires of motor to change the rotating direction of motor.

SHENZHENGUIYUANINDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
Setting control mode Latched: Do notconnect Jumper-1(CN1) or Jumper-2 (CN2)
Press button ▲of first row: motor of receiver 1 rotates in positive direction.
Press button ▼of first row: motor of receiver 1 rotates in reversal direction.
…
Press button ▲of fourth row: motor of receiver4 rotates in positive direction;
motor of other receiver stops.
Press button ▼of fourth row: motor of receiver 4 rotates in reversal direction.
Setting control mode Momentary: Only connect Jumper-1 (CN1)
Press and hold button ▲of first row: motor of receiver 1 rotates in positive direction. Release button ▲of firstrow: Motor stops.
Press and hold button▼of firstrow: motor of receiver 1 rotates inreversal direction. Release button ▼of first row: Motor stops.
…
Press and hold button ▲of fourth row: motor of receiver 4 rotates in positive direction. Release button ▲of fourthrow: Motor stops.
Press and hold button▼of fourth row: motor of receiver 4 rotates inreversal direction. Release button ▼of fourthrow: Motor stops.
Limit controlterminals:
Limit control terminals S1 and S2 are normally open, youcanconnect limit switches or sensors (normally open type) to terminals S1 and S2, and
then youcan use limit switches orsensors tostop the motor.
When motor rotates in positive direction, if connect two terminals of S1, themotor w illstop automatically.
When motor rotates reversal direction, if connect two terminals of S2, the motor will stop automatically.
Wired control terminals:
Youcanconnect manual switches, external devices or sensors (w ith low level output signal) to control the motor.
1) The manual switches:
You can connect manual switches to terminals “Signal 1+”, “Signal 1-”, “Signal 2+”, “Signal 2-”, then you can use manual switches to control the
motor.
When connect terminals “Signal 1+”and“Signal 1-”, motorrotates in positive direction.Andwhen disconnect “Signal 1+”and “Signal 1-”, motor stops.
When connect terminals “Signal 2+”and “Signal 2-”, motor rotates in reversal direction. And when disconnect “Signal 2+”and “Signal 2-”, motor
stops.
2) Signal input:
You can connect external devices (with low level output signal) to terminals “Signal 1+”, “Signal 1-”, “Signal 2+”, “Signal 2-”, then the external
device’s outputsignal cancontrol the motor.
When the externaldevice outputs low level signal to terminal “Signal 1-”and “Signal 1+“, motor rotates in positive direction.
When the external device outputs low level signal to terminal “Signal 2-”and “Signal 2+“, motor rotates inreversal direction.
How to pair the transmitter to the receiver:
1) Press thelearning button of receiver for 1- 2seconds; signal LED on the receiver is on. The receiver enters intostatus of LEARNING.
2) Press any one button on transmitter. If signal LEDflashes quickly 15times and turns off, it means learning issuccessful.
3) When receiver is in thestatus of LEARNING, press again the button of receiver,signalLEDturns off, learning processwillbe discontinued.
4) The receiver can learn several remote controls with differentcodes.
Delete alltransmitters:
We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote
controls,whicharestored in thereceiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes havebeen deleted successfully.

SHENZHENGUIYUANINDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
S1
CN2
CN1
S2
Control AC Motor
External Device
RF module
Antenna
Signal LED
Learning Button
Limit Terminals
ACMotor
Power Supply
N
L
UP
M
DOWN
+
Relay1
Relay2
Power LED
Status LED 1
Status LED 2
Live wire
Neutralwire
COM
Signal 1+
Signal 1-
Signal 2-
Signal 2+
AC Power Supply