Flying Industry Development S1PUB-DC09 User manual

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
RF Wireless Remote Control Radio Controller / Transmitter & Receiver
Package Include:
12 x Receiver: S1PUB-DC09 / S1PUB-DC12 / S1PUB-DC24 (1 Channel / Three Control Modes)
1 x Transmitter: CV-12
1 x User manual
Feature:
Wireless control, easy to install
Control Lights, Motors, Fans, electrically operated Doors / Locks / Windows / Blinds / Cars or Other Appliances with AC110~240V or DC0~28V.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass
through walls, floors and doors.
With characteristics of reverse power protection and over current protection
Audible / visual indication
Use microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/ several transmitters can control one/ several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Transmitting Frequency: 315MHz / 433MHz
Receiver:
Model No.: S1PUB-DC09 / S1PUB-DC12 / S1PUB-DC24
Channel: 1 CH
Control Mode: Toggle, Momentary, Latched
Coding Type: Learning code
Coding Setting: By learning
Power Supply (Operating Voltage): DC12V±1V (S1PUB-DC12), DC9V±1V (S1PUB-DC09), DC24V±1V (S1PUB-DC24)
Working Voltage Range of Relay: AC110~240V or DC0~28V
PCB size: 74mm x 52mm x 24mm
Case size: 79mm x 58mm x 35mm
Maximum Working Current: 30A
Transmitter:
Model No.: CV-12
Channel: 12 CH
Remote Control Distance: 500m / 1500ft (theoretically)
Encode: Fixed code by soldering
Unit size: 110mm x 50mm x 18mm
Power Supply: 1 x 23A -12V battery (included, can be used for 12 months)
Usage:
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following operation):
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle: Press -> On; Press again -> Off.
Press button 1: Turn on Receiver 1 (connect A and B, disconnect A and C)
Press button 1 again: Turn off Receiver 1 (disconnect A and B, connect A and C)
…
Press button 12: Turn on Receiver 12 (connect A and B, disconnect A and C)
Press button 12 again: Turn off Receiver 12 (disconnect A and B, connect A and C)
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button 1: Turn on Receiver 1 (connect A and B, disconnect A and C)
Release button 1: Turn off Receiver 1 (disconnect A and B, connect A and C)
…
Press and hold button 12: Turn on Receiver 12 (connect A and B, disconnect A and C)
Release button 12: Turn off Receiver 12 (disconnect A and B, connect A and C)
Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, other relays Off; Press another button -> Off.
Press button 1: Turn on Receiver 1 (connect A and B, disconnect A and C)
Press any other button: Turn off Receiver 1 (disconnect A and B, connect A and C)
…
Press button 12: Turn on Receiver 12 (connect A and B, disconnect A and C)
Press any other button: Turn off Receiver 12 (disconnect A and B, connect A and C)

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of
remote controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all
stored codes have been deleted successfully.
LEARNING the remote control:
1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) Press any button on the transmitter; the receiver will learn the corresponding button on the transmitter.
4) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, it means learning process is
discontinued.
5) The receiver can learn several remote controls with different codes.
Application: For DC motor or lamp
Relay
Application Circuit
A, B=Normally Open; A, C=Normally Closed.
Power supply
DC0~28V / AC110~240V
Lamp
+
_
A
B
C
Relay
+
_
Power supply
Motor
M
+
_
A
B
C
Antenna
RF module
IC
Jumper-1
Jumper-2
Button
Signal LED
Power LED
Antenna
RF module
IC
Jumper-1
Jumper-2
Button
Signal LED
Power LED