Follett H_C700AHS User manual

00978759R00
Order parts online
www.follettice.com
Horizon™Ice Machines with RIDE™Technology
Installation Instructions for Harmony™
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com
H_C700AHS, H_C700WHS,
H_D700AHS, H_D700WHS,
H_E700AHS, H_E700WHS
(See model number congurator on page 2 for details.)
Horizon Satellite-ll icemakers
t most countertop dispensers manufactured by
Cornelius • Lancer • SerVend
self-contained

2self-contained HARMONY • RIDE Technology
Horizon Series Ice Machine Model Number Configurations
A Air-cooled, self-contained
W Water-cooled, self-contained
A V SC 700HC
C 208-230/60/1
(self-contained only)
D 115/60/1 self-contained
E 230/50/1
(self-contained only)
Icemaker Voltage Series Condenser
V Vision™
H Harmony™
B Ice storage
bin
J Drop-in
700 up to
750 lbs
(340kg)
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
Application Configuration
HC Horizon
Chewblet®
HM Horizon
Micro Chewblet®

3
HARMONY • RIDE Technology self-contained
Front cover
8
Internal connection
7
Ice transport tube
5
External connection
6
Louvered docking assembly
4
Dispenser preparation
3
Site preparation
2
Unpack
1
Read and complete the following 8 installation steps

4self-contained HARMONY • RIDE Technology
Carefully unpack and inspect the contents of your Follett icemaker. 1
Unpack
7/16"
7/16"



Unpack icemaker
1. 1

5
HARMONY • RIDE Technology self-contained
NEMA
6-15
H_D700A/W
NEMA
5-15
H_D700A/W
1/4"
1'




Prepare the installation site. 2
Site preparation
Electrical ➊
• H_C700(A/W)HS 208-230/60/1-15 amp breaker • H_D700(A/W)HS 115/60/1-15 amp breaker
(H_C700A/W Requires a 15 amp dedicated circuit) (H_D700A/W Requires a 15 amp dedicated circuit)
• H_E700(A/W)HS 230/50/1-15 amp‡breaker
(H_E700A/W Requires 15 amp circuit 1.50 mm2wire)
‡ Plug must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination.
Potable water supply ➋
• 10-70 psi (69-483kpa)
• 45 to 90 F (7 to 32 C)
• Water supply must be treated by a scale-inhibiting lter (item# 00130286)
Condenser water supply for water-cooled systems ➌
• 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.)
• 20 to 90 F (-7 to 32 C)
• 1.5 gallons per minute (5.68 liters per minute)
Drain ➍
• The drain line from the ice machine must be vented and have at least 1/4” per foot
(6,4mm/0,3m) pitch
2.1
Provide drainage, water supply and electrical power to within 6 feet
(2m) of icemaker in accordance with local and national codes. Outdoor
installation is not recommended and will void warranty.
115V ±5%
208V -5% to 230V +5%
Installation site requirements
2.1

6self-contained HARMONY • RIDE Technology
Prepare the dispenser. 3
Dispenser preparation
5"
(127mm)
3" ∅
(76,2mm)
• Locate hole position 5" (127mm) from
back of dispenser top
• Cut 3" (77,2mm) diameter hole in
dispenser top
Top preparation
3.1
• Remove protective tape from gaskets
Top preparation
3.2
➋
➊
➌
➊
• Apply gaskets
➊
• Install shuttle actuator ➋ through
dispenser top and secure with locking nut
➌
Top preparation
3.3
➋
➊
• Screw 4" (102mm) extension ➊ into
bottom of shuttle actuator ➋
Top preparation
3.4

7
HARMONY • RIDE Technology self-contained
ON
OFF
Cornelius models ED, DB, DF, IDC and
FLAVOR FUSION
Adjust the agitation timer located on the
Cornelius PC board to 1 second on, 1 hour
off. Note: See Cornelius manual for more
information.
Agitation adjust. – CORNELIUS
3.5
PRESS IN ON
THIS SIDE TO
TURN SWITCH
ON.
SWITCH
ON
SWITCH
OFF
PRESS IN ON
THIS SIDE TO
TURN SWITCH
OFF.
ROCKER
SWITCHES
(VIEW LOOKING
DOWN)
SIDE VIEW
SIDE VIEW
12345678
OFF
SWITCH
NUMBER
AGITATION FREQUENCY
NO AGIT
ATION
10 MINUTES
20 MINUTES
30 MINUTES
40 MINUTES
50 MINUTES
60 MINUTES
70 MINUTES
80 MINUTES
90 MINUTES
100 MINUTES
110 MINUTES
120 MINUTES
130 MINUTES
140 MINUTES
150 MINUTES
5
6
7
8
O
O
O
O
O
O
O
X
O
O
X
O
O
O
X
X
O
X
O
O
O
X
O
X
O
X
X
O
O
X
X
X
X
O
O
O
X
O
O
X
X
O
X
O
X
O
X
X
X
X
O
O
X
X
O
X
X
X
X
O
X
X
X
X
SWITCH
NUMBER
AGITATION TIME
1 SECOND
2 SECONDS
3 SECONDS
4 SECONDS
3
4
O
O
O
X
X
O
X
X
X = ON
O = OFF
Lancer 4500 series only
Adjust the agitation time to 1 second, and the agitation frequency to 150 minutes. See Lancer
manual for more information.
Agitation adjustments – LANCER 4500 SERIES
3.6

8self-contained HARMONY • RIDE Technology
Major/Minor
FS-16 Setup
Config Bonus Key
Soda/Plain Water
Config Dispense Only
PC Mode
PC Time
Ice Stir Off
Ice Stir On
Sold Out
Carb Sensors
Ice Bin Sensors
Valve Code Version
Number Of Valves
Reset Defaults No Yes
Reload Defaults?
1 2 3 4
12 0.104 0.104
1000
Ice Bin Optic
Upper Lower
Sold Out #1
Selection Sold Out
05000
On Time (MSEC)
Off On
Set PC Mode Menu
V:1 B1 DLY1
Dispense Delay
V:2 1:S 2:W 3:S 4:W
V:1 T:F M:S B:W
Bonus Key Setup
Brands Per Side
V:1 L:2 R:1
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
Soda/Plain Water
OFF Time (MIN)
00150
On Time (MSEC)
01000
1000 500
34 0.104 0.104
On On On On
V:1 B:1
Sold Out #1
Off
Sold Out #1
Ver. 0.200
Lancer FS-16
Sub-CatagoryMain Menu
Initialization Screen
2nd Sub-Catagory
(Boot Up Only)
Cancel Enter
Scrolls through Main Menu
Press "Enter" to enter sub-catagory
Moves curser to right or left
Changes value (number/letter)
Press "Enter" to enter save changes
Press "Cancel" to exit menu
➊
Lancer FS series only
• Hold down “cancel” and “left button” to get to hidden menu ➊
• Type in code 6655
• Type in 150 minutes “off time” and 1000 milliseconds (1 second of time) as the preferred setting
Note: See Lancer manual for more information
Agitation adjustments – LANCER FS SERIES
3.7
Agitation adjustments – SERVEND
3.8
SerVend models only
No agitation adjustment required

9
HARMONY • RIDE Technology self-contained
10-32 nut
flat washer
ice chute
gasket
apply food-grade
silicone sealant
to this surface
to seal to bin gate
mounting plate
ice diverter
(supplied)
mounting
gate
plate
storage bin
plate
gate
restrictor
gate opening
bin through
into storage
flange extends
➋
➊
Cornelius ED, DF and DB series only
These dispensers require the installation of an ice diverter at the dispenser opening.
• Disassemble chute assembly
• Discard factory restrictor plate ➊
• Replace with alternate diverter plate, ➋(supplied)
Dispenser diverter plate installation – CORNELIUS ED, DF and DB SERIES
3.9

10 self-contained HARMONY • RIDE Technology
➊
➋
adjust restrictor
plate to fully
open position
Cornelius IDC and Flavor Fusion
These dispensers require the adjustment of the ice restrictor plate.
• Loosen four nuts on ice chute assembly ➊
• Adjust restrictor plate to fully open position ➋
• Replace four nuts and tight to 50 in lbs (max.)
Restrictor plate adjustment – CORNELIUS IDC and FLAVOR FUSION
3.10