Follett HCC1000ABS User manual

208264
208264
StockModule Identification Plate
StockModule Identification Plate
ServiceNo.
ServiceNo.
ModuleNo.
ModuleNo.
Product
Product
OMRESSORTHERMALLYPROTECTED
OMRESSORTHERMALLYPROTECTED
EastonPennsylvania
EastonPennsylvania
U
AMPS
AMPS
AMPS
AMPS
VOLTS
VOLTS
NSF
NSF
PHASE
PHASE
SINGLE
SINGLE
CHARGE
CHARGE
LOWSIDE
LOWSIDE
PARTNO
PARTNO
PSIG
PSIG
THEUSA
THEUSA
MADEIN
MADEIN
OZ
OZ
LL
U
R
C
R
HZ
HZ
Order parts online
www.follettice.com
self-contained
00159889R07
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com
Horizon™Ice Machine Models with RIDE™Technology
Installation Instructions for Ice Storage Bins
HCC1000ABS, HMC1000ABS, HCC1400ABS, HMC1400ABS,
HCC1000WBS, HMC1000WBS, HCC1400WBS, HMC1400WBS,
HCE1000ABS, HME1000ABS, HCE1400ABS, HME1400ABS,
HCE1000WBS, HME1000WBS, HCE1400WBS, HME1400WBS
(See model number congurator on page 2 for details.)

2self-contained BIN • RIDE Technology
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
400 up to
454 lbs
(206kg)
1000 up to
1036 lbs
(471kg)
1400 up to
1450 lbs
(658kg)
1650 up to
1580 lbs
(717kg)
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
CondenserSeriesVoltageIcemaker
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
MC Maestro™
Chewblet®
(400 Series)
HC Horizon
Chewblet
(1000, 1400,
1650 Series)
HM Horizon
Micro Chewblet
HC 1400CSVA
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
Chewblet®Ice Machine Model Number Configurations

BIN • RIDE Technology self-contained 3
87
5 6
43
21
Read and complete the following 8 installation steps
Front coverInternal connection
External connection
Louvered docking assembly
Bin preparation
Site preparationUnpack
Ice transport tube

4self-contained BIN • RIDE Technology
Carefully unpack and inspect the contents of your Follett ice machine. 1
Unpack
1/2"
1/2"
➊➋
➌➍
➎➏
Unpack ice machine
1. 1

BIN • RIDE Technology self-contained 5
Prepare the installation site. 2
NEMA
6-20
H_C1400A/W
H_C1000A/W
NEMA
6-15
H_E1000A/W‡



1' (0,3m)
1/4" (6,4mm)
H_E1400A/W‡
requires 15A circuit,
1.50 mm2wire
requires 20A circuit,
4.00 mm2wire
Site preparation
2.1
Provide drainage, water supply and electrical power to within 6 feet (2m)
of ice machine in accordance with local and national codes. Outdoor
installation is not recommended and will void warranty.
Electrical ➊
• H_C1000(A/W)BS 208-230/60/1-15 amps • H_C1400(A/W)BS 208-230/60/1-20 amps
• H_E1000(A/W)BS 230/50/1-15 amps‡• H_E1400(A/W)BS 230/50/1-20 amps‡
(H_E1000A/W requires 15A circuit, 1.50 mm2wire) (H_E1400A/W requires 20A circuit, 4.00 mm2wire)
‡ Plug must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination.
Potable water supply ➋
• 10-70 psi (69-483kpa)
• 45 to 90 F (7 to 32 C)
• Follett recommends the use of an in-line water ltration system (#00130286)
Condenser water supply for water-cooled systems ➌
• 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.)
• 45 to 90 F (7 to 32 C)
• 1.5 gallons per minute (5.68 liters per minute)
Drain ➍
• The drain line from the ice machine must have at least 1/4" per foot pitch (6,4mm/0,3m)
Installation site requirements
2.1

6self-contained BIN • RIDE Technology
Prepare the bin 3
Bin preparation
• Remove protective tape from gaskets
Bin top preparation
3.1
➋
➊
➊
➌
• Apply gaskets
➊
• Install shuttle actuator ➋ through
dispenser top and secure with locking nut
➌
Bin top preparation
3.2

BIN • RIDE Technology self-contained 7
Louvered docking assembly 4
• Mount louvered docking assembly to wall
bracket accessory
Wall bracket accessory
• Mount louvered docking assembly to
machine stand accessory
Machine stand accessory
WARNING
• Docking station must be secured in accordance with these instructions to ensure ice machine
stability.
• Ventilation openings in the louvered docking station should be clear of obstruction
4.1 4.2
Install the louvered docking assembly.

8self-contained BIN • RIDE Technology
Ice transport tube
Install the ice transport tube. 5
1' (0,3m)



¡
¢





Hot Water
160 F (71 C)
1/4˝ (6,4mm)
Ice transport tube tips
• Insulate entire length of ice transport tube ➊
• Secure ice transport tube ➋as needed to prevent dips and traps from forming. For long tube
runs see guide on page 14.
• Pitch ice transport tube at least 1/4" per foot (6,4mm/.3m) ➌
• Ice transport tube must drain towards ice machine
Ice transport tube to bin
• Be sure tube ends are square ➍
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➎
before making connection to ease assembly
• Push ice transport tube onto ice machine nipple ➏
• Install hose clamp ➐
Ice transport tube to Ice machine
• Be sure tube ends are square ➑
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➎
before making connection to ease assembly
• Push ice transport tube onto ice machine nipple ➒
• Install hose clamp ➓
Ice transport tube installation
5.1

BIN • RIDE Technology self-contained 9
Connect utilities to louvered docking assembly. 6
External connections
➊
➌
➋
➍
➋
➊
• Remove access panel if necessary
• Install drain line ➊.
The rigid drain line from the ice machine
must have at least 1/4" per foot pitch
(6,4mm/0,3m).
• Install ice machine potable water
supply ➋
• Replace access panel
Air-cooled ice machines only
• Remove access panel if necessary
• Install drain line ➊.
The rigid drain line from the ice machine
must have at least 1/4" per foot pitch.
• Connect cooling water supply ➋and
return ➌
• Install ice machine potable water
supply ➍
• Replace access panel
Water-cooled ice machines only
6.1 6.2

10 self-contained BIN • RIDE Technology
Connect louvered docking assembly to ice
machine. 7
Internal connections
Air-cooled ice machines – follow steps 7.1 through 7.4.
➊
➋
• Slide ice machine into louvered docking
assembly ➊
• Insert ice transport tube all the way into
coupling and tighten nut rmly ➋
Ice transport tube
7. 1
➊
➋
➊
➋
• Insert potable water line into valve ➊
• Push drain line over hose barb on
back of evaporator mount ➋
Potable water line
7. 2
• Position plate into opening and secure
with supplied screw
Power cord
7. 4
➊
• Remove twist tie
• Carefully pass plug thru opening and plug
into wall outlet
Power cord
7. 3
CAUTION
• Plug must be accessible after nal installation.
• H_E1400A/W 230/50/1 requires a 20A circuit (4.00 mm2wire)