Forest garden SDP64 User manual

Shiplap Pent Shed
6' x 4'
Important :
Assembly of this
shed requires a
minimum of two
adults.
Issue 0215
B
SDP6BK
BACK PANEL
SDP4RHS
RIGHT SIDE
179112808
ROOF SHEET
DEF
A
SDP64 PARTS LIST
BRDFL46
FLOOR
SDRDT
DOOR
SDP6FR
FRONT PANEL
40121830PARDTR
1830mm CORNER STRIP QTY 2
G
Place the corner strips so that they cover the joins between
the panels. Fix each in place using 3 x 30mm screws
2
4
11
C
SDP4LHS
LEFT SIDE
3
REQUIRED TOOLS :
(NOT SUPPLIED)
TAPE MEASURE HAMMER
PCWIN1
WINDOW QTY 1
H
Top View
B
D
A
Must Pre drill for
each screw used.
FELT QTY 1
85008
Fixing Pack (SDP64FP)
This fixing pack is used for several products.
There may be additional fixings.
Not to Scale
Flush Hinge
Qty 2
50mm Screw Qty 22
30mm Nail Qty 42
25mm Screw Qty 19
Hasp & Staple
30mm Screw Qty 25
10mm Felt tacks
Qty 80
SHARP KNIFE
AC
Z’ bracket Qty 2
40121717PARDTR
1717mm CORNER STRIP QTY 2
37281791
1791mm BATTEN QTY 2
59121280PDT
1280mm BARGE BOARD QTY 2
37281699
1699mm BATTEN QTY 1
25120675PDT
675mm STRIP QTY 1
84996
675mm PLASTIC STRIP QTY 3
F
I
J
K
L
M
N
P
B
C
D
A
J
O59121815PDT
1815mm BARGE BOARD QTY 1
25mm Security Screws
Screws Qty 8
FLAT HEAD
SCREWDRIVER
POZI DRIVE
SCREWDRIVER
SCISSORS
Place the hinge against the inside of the door frame
and position the large section of the hinge so that it is
flush with the inside of the framing, as shown. Fix
with 25mm screws.
Open the hinge and fix the smaller section to the
door framing. Again make sure that the hinge is flush
and that the holes are positioned so that the 25mm
screws locate correctly into the batten.
Q
20121710PDT
20x1710mm STRIP QTY 1
I
Position the staple on the door end in line with the centre batten on the reverse of the door.
Make sure that the staple is in line with the framing behind. Fix in place using 2 x 25mm
screws.
Before fixing the Hasp to the door make sure that it is in line with the framing on the reverse of
the door and that it closes over the Staple. Fix this in place using 3 x 25mm screws.
Place the panels on top of the floor. Make sure that all the panels are tight and flush
before fixing them to each other using 3x50mm screws.
Before fixing each panel to the floor make sure that the panels are sitting flush and fix
them in place using 50mm screws. position each screw so that it locates into the bearers
underneath.
3x50mm screws for the front and back panels.
2x50mm screws for the side panels.
IMPORTANT, RETAIN FOR FUTURE REFERENCE; READ
CAREFULLY
This building is pre-treated with a factory base coat for
protection during storage and transit. We recommend that
you treat your new building as soon as possible after
assembly using a wood preservative treatment. Apply in
accordance with the manufacturers instructions.
- This product must be built on a solid level base.
- The roof of this building is not a load bearing structure.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Due to the nature of the material the doors may need some
trimming for a neater fit.
- Please keep all plastic bags and small parts away from
children
Technical Helpline: 0333 7777 089 8.30 am and 5.00
pm Monday to Friday.
Please check all parts prior to assembly
Assembly of damaged parts may be deemed to be
acceptance and this may affect the remedies you are entitled
to.
If the product is not constructed in accordance with the
instructions, or is altered in any way (e.g. painted), the
manufacturer cannot be held liable for any resulting damage.
Staple
Hasp
Fix the 20 x 1710mm strips to the side of the
door frame so that it is tight with the cladding
and flush with the frame. Use 3 x 30mm
screws for each.
QA

Forest Garden Ltd, Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
Biocidal Product Regulation (EU 528/2012) Article 58 Information
This article contains timber treated with Celcure AC-500, incorporating biocidal products to give protection against wood destroying insects & wood rotting fungi.
Contains: Basic copper carbonate (Copper (II) carbonate – Copper (II) hydroxide (1:1)), Boric acid, Benzalkonium chloride.
Wear gloves when handling freshly treated wood. Avoid breathing dust when cutting treated or untreated wood. Dispose of off-cuts responsibly – do not burn.
89
5
To make the roof position the battens as shown making sure that the 28mm face of each batten is
facing upwards before placing the roof sheet on top.
1.The 1791mm battens should be positioned so that they are flush on all sides of the roof sheet as
shown. When fixing these use a nail at each end first to hold the batten in place and the remaining
nails in 300mm intervals.
3.Place the 1699mm batten (M) 608mm inside from the front batten, and offset 45mm at each end.
Fix each batten in place using 30mm nails spaced in 300mm intervals.
Fix a Z’ bracket to each end of the centre batten using a 25mm screw for each.
7
Lift the roof section into place making sure that it is in line with the
sides.
Fix the roof in place using 30mm nails spaced in approximately
300mm intervals. (Make sure the nails locate into the framework of
the panels)
K
45mm Offset
M
608mm
pencil line
- Be careful when working
at height on ladders.
- The roof is not a load
bearing structure.
Attention
Take care when
cutting and
trimming the roof
felt.
Cut the roof felt into two equal lengths and place the first sheet on top of the roof at the back of the shed
making sure there is equal overhang at the sides and approximately 50mm at the back. Fix the felt in place
using the felt tacks spaced in 150mm intervals. Fold and tack the corners.
Repeat for the other sheet making sure it overlaps the first and use felt nails to fasten the seam.
Place the 1280mm barge boards against the sides of the shed so that they
are in line with the roof. Fix each in place using 3 x 30mm screws.
Position the 1815mm barge board against the front of the shed again in line
with the top if the roof and fix in place using 4x30mm screws.
pencil line
Front
6
Board
H
Lip
P
Attention:
Take care when placing
the screws. These can
not be backed out.
You may need to
cut the plastic
strips to size using
a pair of scissors
Place the window from the outside so that the lip sits on the bottom board as shown.
Place the plastic strips at the top, bottom and right hand side of the window so that one
side of the strip butts up against the cladding. Fix each strip in place using 2 x security
screws.
Place the 675mm wooden strip against the left side of the window so that it overlaps the
window on both sides and the two remaining strips either side of the windows. Again fix
each wooden strip in place using 2 x 25mm screws.
O
L
Maintenance.
We recommend that you treat your shed at the beginning of each season with wood preservative treatment. Apply in
accordance with the manufacturers instructions.
Regularly check (1) All fixings are secure (2) Roofing felt is free of holes and tears (3) Sand off any rough/sharp edges.